Altronix ACM Series Access Power Controllers ka Lisebelisoa tsa Matla

Fetileview

Litsi tsa Altronix ACM Series li aba le ho fetola matla ho fihlella litsamaiso tsa taolo le lisebelisoa. Ba fetola tlhahiso ea 115VAC 60Hz ho tse robeli (8) tse laoloang ka boithaopo tsa 12VDC kapa 24VDC tse sirelelitsoeng ka fuse. Lisebelisoa tsena tsa motlakase li ka fetoleloa ho likhokahano tsa "C" tsa mofuta o omileng. Lintho tse hlahisoang li hlahisoa ke sink e bulehileng ea pokello kapa ka tloaelo e bulehileng (NO) e kenya letsoho e omileng ho tloha ho Access Control System, Card Reader, Keypad, Push Button, PIR, joalo-joalo Li-Units li tla tsamaisa matla ho lisebelisoa tse fapaneng tsa ho laola lisebelisoa tsa lisebelisoa tse kenyeletsang Mag Locks. , Ho Otloa ha Motlakase, Lits'oants'o tsa Menyako ea Magnetic, joalo-joalo Lintho tse hlahisoang li tla sebetsa ka mekhoa e 'meli ea Fail-Safe le/kapa Fail-Secure. FACP Interface e nolofalletsa Emergency Egress, le Alarm Monitoring, kapa e ka sebelisoa ho kenya lisebelisoa tse ling tse thusang. Karolo ea ho khaola alamo ea mollo e ka khethoa ka bonngoe bakeng sa liphetho tse robeli kapa tse robeli (8).

ACM Series Configuration Reference Chart

Altronix Nomoro ea Mohlala

Kenyeletso ea 115VAC 60Hz (mokhoa oa hajoale)

Tekanyetso ea Motlakase oa Boto ea Phepelo ea Matla

Boto ea Phepelo ea Matla Battery Fuse Rating

Teko e Phahameng ea Battery ea Hona Joale

12VDC Kakaretso ea Sephetho sa Hona Joale

24VDC Kakaretso ea Sephetho sa Hona Joale

Liphello Tse Kopanetsoeng

Motho ka Mong oa Sephetho

Sehlopha sa 2 se Lekanyelitsoe Matla-A lekanyelitsoeng

Lintlha tsa Setsi

UL Lists le File Lipalo

Tlhaloso: AL400ULACM

3.5A

5A/

15A/

0.7A

4A

3A

8

3.5A

P

THABISENG

140 58th St. Brooklyn, NY         Lefapha la NYC la California Buildings State Fire Marshal

UL File # BP6714 UL 294* UL e thathamisitsoe bakeng sa Litsi tsa Sistimi ea Taolo ea Phihlelo. "Thepa ea Matšoao" E Ekantsoe ho CSA Standard C22.2 No.205-M1983

250V

32V

Tlhaloso: AL600ULACM

3.5A

5A/

–

0.7A

6A

6A

8

3.5A

–

250V

Tlhaloso: AL1012ULACM

2.6A

5A/

15A/

0.7A

10A

–

8

3.5A

–

250V

32V

Tlhaloso: AL1024ULACM

4.2A

5A/

15A/

3.6A

–

10A

8

3.5A

–

250V

32V

Altronix Nomoro ea Mohlala	* ANSI/UL 294 7th Ed. Maemo a Tshebetso a ho Finyella
	Tlhaselo e Senyang	Teko ea Mamello	Line Security	Ema ka matla
Tlhaloso: AL400ULACM	I	IV	I	I
Tlhaloso: AL600ULACM	I	IV	I	I
Tlhaloso: AL1012ULACM	I	IV	I	I
Tlhaloso: AL1024ULACM	I	IV	I	12AH - II, 40AH - III, 65AH - IV

Khumo Voltage le Chate ea Litlhaloso tsa Stand-by

Tlhaloso: AL400ULACM

Moqtage	Fetola Boemo	Battery e emeng	4 hora. Ema-hang / 5 mets. Alamo	24 hora. Ema-hang / 5 mets. Alamo
12VDC	SW1 – ON	40AH	3.5A / 3.5A	0.5A / 3.5A
24VDC	SW1 - TLOA	40AH	2.75A / 2.75A	0.75A / 2.75A

Tlhaloso: AL600ULACM

Moqtage	Fetola Boemo	Battery e emeng	4 hora. Ema-hang / 5 mets. Alamo	24 hora. Ema-hang / 5 mets. Alamo
12VDC	SW1 – ON	40AH	5.5A / 5.5A	0.5A / 5.5A
24VDC	SW1 - TLOA	40AH	5.75A / 5.75A	0.75A / 5.75A

Tlhaloso: AL1012ULACM

Moqtage	Fetola Boemo	Battery e emeng	4 hora. Ema-hang / 5 mets. Alamo	24 hora. Ema-hang / 5 mets. Alamo
12VDC	N/A	40AH	9.5A / 9.5A	0.5A / 9.5A

Tlhaloso: AL1024ULACM (sheba ho AL1024ULACM Leqephe la Tshebetso la Battery size

Moqtage	Battery e emeng	15 mets. Ema-hang / 5 mets. Alamo	4 hora. Ema-hang / 5 mets. Alamo	24 hora. Ema-hang / 5 mets. Alamo	60 hora. Ema-hang / 5 mets. Alamo
24VDC	12AH	7.7A / 9.7A	1.2A / 9.7A	–	–
24VDC	65AH	–	7.7A / 9.7A	1.2A / 9.7A	200mA / 9.7A

Litlhaloso

Kenyeletso

• Kenyelletso ea matla 115VAC, 60Hz (bona ACM Series Power Supply Configuration Reference Chart, pg. 2).

Likhetho tsa ho Kenya Matla a ACM8:
a) Motlakase o le mong (1) o tloaelehileng bakeng sa ACM8 le matla a ho notlela (fektheri e kentsoe).
b) Lisebelisoa tsa motlakase tse peli (2) tse arohaneng (ho hlokahala matla a kantle). Hona joale ho khethoa ke phepelo ea motlakase e hoketsoeng, e se ke ea feta palo e kholo ea 10A.

• Tse robeli (8) Sistimi ea Taolo ea Phihlello e kenya lintho tse kenang. Likhetho tsa ho kenya:

a) Tse robeli (8) tse atisang ho buloa (NO).
b) Tse robeli (8) tse bulehileng tsa pokello.
c) Motsoako ofe kapa ofe oa tse ka holimo.

Litholoana

• Liphetho tse robeli (8) tse laoloang ka boikemelo. Likhetho tse hlahisoang:

a) Lits'oants'o tse robeli (8) tsa Fail-Safe le/kapa Fail-Sireletseha liphetho tsa motlakase.
b) Liphetho tse robeli (8) tsa "C" 5A tse lekantsoeng ka phetiso.
c) Motsoako ofe kapa ofe oa tse ka holimo.

• Liphello tse robeli (8) tse thusang (tse sa fetoheng).
• Li-fuse tse hlahisoang ke ACM8 li fuoe lintlha tse 3.5A.
• Fuse e kholo ea boto ea ACM8 e lekantsoe ho 10A.
• Ho khaoha ha Alarm ea Mollo (ho latching kapa ho se lache) ho ka khethoa ka bonngoe bakeng sa liphetho tse robeli (8).
• Likhetho tsa ho kenya Alarm ea Mollo:
  a) Ka tloaelo ho buloa (NO) kapa ka tloaelo ho koetsoe (NC) ho omella ho kopanya.
  b) Kenyelletso ea ho khutlisa polarity ho tsoa ho potoloho ea matšoao a FACP.

Litholoana
Phatlalatso ea li-alarm e bonts'a hore tlhahiso ea FACP e qalile (foromo "C" ea ho ikopanya e rated @ 1A 28VDC, ha e hlahlojoe ke UL).

• Litholoana tse tlhotliloeng le tse laoloang ka elektroniki.
• Tšireletso ea mocheso le e khutšoanyane ea potoloho e nang le auto reset.

Matšoao a bonoang:

• LED e tala e bonts'a ha FACP e khaotsoe.
• Li-LED tse khubelu li bonts'a hore lihlahisoa li hlahisoa (li-relays li matlafalitsoe).
• Lipontšo tsa LED tsa AC le tse hlahisoang ke DC.

Boloka Battery:

• Chaja e hahelletsoeng ka hare bakeng sa asiti ea lead e tiisitsoeng kapa libeteri tsa mofuta oa gel.
• Jarolla ka ho iketsa ho ea stand-by betri ha AC hloleha.
• Leqhubu la Zerotage theoha ha o fetohela ho backup ea betri.

Tlhokomelo:

• AC e hloleha ho laola (foromo "C" lebitso).
• Tlhokomelo e tlase ea betri (ho ikopanya le "C").
• Tlhokomelo ea boteng ba betri (foromo "C").
• Power fail supervision relay (foromo "C" contact rated 1A @ 28VDC).

Litekanyo kampetsoeng:

• 15.5" x 12" x 4.5"
• (393.7mm x 304.8mm x 114.3mm).
• Sebaka sena se na le libeteri tse fihlang ho tse peli (2) tsa 12AH.

Litaelo tsa ho Hloma

Mekhoa ea likhoele e tla tsamaellana le Khoutu ea Naha ea Motlakase/NFPA 70/NFPA 72/ANSI, le likhoutu tsohle tsa lehae le ba boholong ba nang le matla a ho laola. Sehlahisoa se reretsoe ho sebelisoa ka tlung feela.

1. Beha yuniti sebakeng se lakatsehang. Tšoaea le ho phunya masoba leboteng ho tsamaisana le likoti tse peli tse ka holimo sebakeng se kampetsoeng. Kenya li-fasteners le li-screws tse peli leboteng 'me lihlooho tsa screw li hlahelle. Beha likoti tse ka holimo tsa sekoahelo holim'a likurufu tse peli tse ka holimo; boemo le ho sireletseha. Tšoaea boemo ba likoti tse peli tse tlase. Tlosa sebaka se kampetsoeng. Cheka likoti tse ka tlase ebe u kenya li-fasteners tse tharo. Beha masoba a ka holimo a kokelo holim'a likurufu tse peli tse ka holimo. Kenya li-screw tse peli tse tlase 'me u tiise hore u tiisa li-screw tsohle (Enclosure Dimensions, pg. 12). Sireletsa sebaka se kampetsoeng fatše. E kgothaletswa ho qala review litafole tse latelang ho thusa ho kenya:
   Khumo Voltage le Chate ea Litlhaloso tsa Boemo ba Boemo (leq. 2)
   Setšoantšo se Tloaelehileng sa Tšebeliso (leq. 7)
   Tlhahlobo ea LED (leq. 7)
   Litafole tsa Boitsebiso ba Terminal (leq. 6)
   Litšoantšo tsa ho kopanya (leq. 9-10)
2. Seta tlhahiso voltage
   AL400ULACM le AL600ULACM: beha sephetho se lakatsehang sa DCtage ka ho beha switjha SW1 sebakeng se loketseng botong ea phepelo ea motlakase. AL1012ULACM ke feme e behiloeng ho 12VDC mme AL1024ULACM ke feme e behiloeng ho 24VDC (Output Vol.tage le Chate ea Litlhaloso tsa Stand-by, leq. 2).
3. Kopanya AC
   Hokela matla a AC a sa fetoheng (115VAC 60Hz) ho litheminale tse tšoailoeng [L, N]. Sebelisa 14 AWG kapa e kholoanyane bakeng sa likhokahano tsohle tsa matla. Sireletsehile terata e tala lebisa fatše fatše. Tala ea "AC" LED botong ea phepelo ea motlakase e tla bulela. Leseli lena le ka bonoa ka lense ea LED e monyako oa sebaka se kampetsoeng. Boloka likhoele tse lekanyelitsoeng matla li arohane le lithapo tse se nang matla (115VAC 60Hz Input, Battery Wires). Bonyane sebaka sa sebaka sa 0.25" se tlameha ho fanoa.
   TLHOKOMELISO: U se ke ua tšoara likarolo tsa tšepe tse pepenene. Koala matla a potoloho ea lekala pele u kenya kapa u sebeletsa lisebelisoa. Ha ho na likarolo tse ka sebelisoang ke mosebelisi kahare. Fetisetsa ho kenya le ho fana ka litšebeletso ho basebeletsi ba nang le tsebo.
4. Lekanya voltage pele o kopanya lisebelisoa. Sena se thusa ho qoba tšenyo e ka bang teng.
5. Dikgetho tsa tlhahiso
   Yuniti e tla fana ka liphetho tse robeli (8) tsa matla a fetotsoeng, tse robeli (8) tse omeletseng tsa "C", kapa motsoako ofe kapa ofe oa matla a fetotsoeng le liphetho tsa "C", hammoho le lisebelisoa tse robeli (8) tse sa fetoheng.
   (a) Lits'oants'o tsa Matla a fetotsoeng:
   Hokela molaetsa o fosahetseng (–) oa sesebelisoa se tsamaisoang ho terminal e tšoailoeng [COM]. Bakeng sa ts'ebetso ea Fail-Safe, hokela molaetsa o nepahetseng (+) oa sesebelisoa se tsamaisoang ho theminale e tšoailoeng [NC]. Bakeng sa ts'ebetso ea Fail-Sireletsehile, hokela ho kenya letsoho (+) ho sesebelisoa se tsamaisoang ho terminal e tšoailoeng [NO].
   (b) Liphetho tsa Foromo ea "C":
   Ha foromo ea "C" e lakatseha, fuse e tsamaisanang le eona (1-8) e tlameha ho tlosoa. Hokela negative (–) ea phepelo ea motlakase ka kotloloho ho sesebelisoa sa ho notlela. Hokela positi (+) ea phepelo ea motlakase ho theminale e tšoailoeng [C]. Bakeng sa ts'ebetso ea Fail-Safe, hokela positi (+) ea sesebelisoa se tsamaisoang ho theminale e tšoailoeng NC]. Bakeng sa ts'ebetso ea Fail-Sireletsehile hokela positi (+) ea sesebelisoa se tsamaisoang ho theminale e tšoailoeng [NO].
   (c) Lisebelisoa tsa Matla a Tlatsetso (tse sa fetoloang):
   Hokela molaetsa o nepahetseng (+) oa sesebelisoa se tsamaisoang ho theminale e tšoailoeng [C] le negative (–) ea sesebelisoa se tsamaisoang ho theminale e tšoailoeng [COM]. Sephetho se ka sebelisoa ho fana ka matla bakeng sa babali ba likarete, li-keypad, joalo-joalo.
6. Likhetho tsa ho kenya letsoho
   (a) Hangata Bula [NO] trigger ea ho kenya: Litlhahiso tsa 1-8 li kentsoe tšebetsong ka mokhoa o tloaelehileng oa ho kenya sekontiri se bulehileng kapa se bulehileng. Hokela lisebelisoa (libali tsa likarete, li-keypad, kopo ea ho tsoa likonopo, joalo-joalo) ho litheminale tse tšoailoeng [IN] le [GND].
   (b) Open Collector Sink inputs: Hokela setsi sa taolo ea phihlello se bulehileng se bokellang positive (+) ho theminale e tšoailoeng [IN] le negative (–) ho theminale e tšoailoeng [GND].
   
7. Likhetho tsa Sehokelo sa Alarm ea Mollo (Setšoantšo sa 4 ho isa ho sa 8, leqephe la 8): [NC] eo hangata e koetsoeng, eo hangata e bulang [NO] kapa keno e khutlisang polarity ho tsoa ho potoloho ea matšoao ea FACP e tla hlahisa likhetho tse khethiloeng. Ho nolofalletsa FACP Disconnect bakeng sa tlhahiso, tima switch e tsamaellanang [SW1-SW8] TIMA. Ho tima FACP hakoa bakeng sa tlhahiso, bulela switch e tsamaellanang le eona [SW1-SW8].
   (a) Ka tloaelo Bula [NO] ho kenya: Bakeng sa li-hook-ups tse se nang latching (setšoantšo sa 5, leqephe la 9). Bakeng sa ho latching hook-ups bona
   (b) Hangata ho koetsoe [NC]: Bakeng sa li-hook-ups tse se nang latching (setšoantšo sa 7, leqephe la 10). Bakeng sa ho latching hook-ups bona
   (c) Sehlomathisi se kenyang Potoloho ea Letšoao la FACP: Hokela positive (+) le negative (–) ho tloha ho FACP signaling circuit output ho litheminale tse tšoailoeng [+ INP –]. Hokela FACP EOL ho li-terminals tse tšoailoeng [+ RET –] (polarity e hlalositsoe boemong ba alamo). Jumper e haufi le TRG LED e tlameha ho khaoloa
8. FACP Dry form "C" tlhahiso: Hokela sesebelisoa se lakatsehang se ka hlahisoang ke khokahanyo e ommeng ea yuniti ho liteminale tse tšoailoeng [NO] le [C] FACP bakeng sa tlhahiso e tloaelehileng e bulehileng kapa litheminale tse tšoailoeng [NC] le [C] FACP bakeng sa tlhahiso e tloaelehileng e koetsoeng.
9. Likhokahano tsa Battery: Bakeng sa lits'ebetso tsa Access Control, libeteri ke boikhethelo. Haeba libeteri li sa sebelisoe, tahlehelo ea AC e tla fella ka tahlehelo ea matla a tlhahisotage. Libetri li tlameha ho ba le asiti ea lead kapa mofuta oa gel. Hokela betri e le 'ngoe (1) 12VDC ho litheminale tse tšoailoeng [+ BAT -] bakeng sa ts'ebetso ea 12VDC. Sebelisa libeteri tse peli (2) tsa 12VDC tse kentsoeng ka mehala bakeng sa ts'ebetso ea 24VDC.
10. Sephetho sa Battery le AC Supervision: Hoa hlokahala ho hokela lisebelisoa tsa bolebedi tse tlalehang mathata ho dipoelo tse ngotsweng [AC Fail, BAT FAIL] diphetho tsa phepelo ya taolo tse ngotsweng [NC, C, NO] ho lisebelisoa tse loketseng tsa tsebiso. Sebelisa 22 AWG ho isa ho 18 AWG bakeng sa tlaleho ea AC Fail & Low/No Bettery. Khaola "AC delay" jumper ho lieha ho tlaleha ka lihora tse 6.
    Hlokomela: Tamper switch e tlameha ho kengoa le ho hokela sesebelisoa se nepahetseng sa tsebiso ho tlaleha boemo ba bothata ha lemati le koetsoeng le bulehile.
11. Lisebelisoa tse ngata tsa motlakase: Ha u sebelisa li-jumper tse peli (2) tsa lisebelisoa tsa motlakase J1 le J2 (tse ka letsohong le letšehali la li-terminals tsa matla / taolo) li tlameha ho khaoloa Hokela matla a ACM8 ho li-terminals tse tšoailoeng [- Control +] 'me u kopanye matla a lisebelisoa tsa ho notlela liteishene tse tšoailoeng [- Matla +]. Ha u sebelisa lisebelisoa tsa motlakase tsa DC polarity e tlameha ho hlokomeloa. Ha o sebelisa lisebelisoa tsa motlakase tsa AC polarity ha ea lokela ho bonoa
    Hlokomela: Bakeng sa ho latela melao ea UL, phepelo e eketsehileng ea motlakase e tlameha ho se be le matla a fokolang, UL Listed for Access Control Systems le lisebelisoa.

Tlhokomelo

Yuniti e lokela ho lekoa bonyane hang ka selemo bakeng sa ts'ebetso e nepahetseng ka tsela e latelang:
Khumo Voltage Teko: Tlas'a maemo a tloaelehileng a mojaro, molumo oa DC oa voltage lokela ho hlahlojwa bakeng sa vol e nepahetsengtage level (Output Voltage le Chate ea Litlhaloso tsa Stand-by, maq. 2).
Teko ea Betri: Tlas'a mojaro o tloaelehileng, maemo a lekola hore na betri e tjhajiloe ka botlalo, hlahloba molumo o boletsoengtage liteisheneng tsa betri le liteisheneng tsa boto tse tšoailoeng [+ BAT –] ho netefatsa hore ha ho na ho khaoha lithapong tsa ho hokela betri.
Hlokomela: AL400ULXB2, AL600ULXB, AL1012ULXB (Boto ea Phepelo ea Matla) boholo ba tefiso ea hajoale ke 0.7A. AL1024ULXB2 (Boto ea Phepelo ea Matla) boholo ba tefiso ea hajoale ke 3.6A. Bophelo ba betri bo lebelletsoeng ke lilemo tse 5, leha ho le joalo, ho khothalletsoa ho fetola libeteri nakong ea lilemo tse 4 kapa ka tlase ha ho hlokahala.

Litafole tsa Boitsebiso ba Terminal

Boto ea Phepelo ea Matla

Terminal Taba	Mosebetsi/Tlhaloso
L, G, N	Hokela 115VAC 60Hz ho li-terminals tsena: L ho ea ho chesa, N ho se nke lehlakore. Se ke oa sebelisa G terminal botong ea phepelo ea motlakase (bona Hokela AC, leq. 3).
+ DC -	AL400ULACM - 12VDC @ 4A kapa 24VDC @ 3A ho ACM8 board (matla a fokolang). AL600ULACM - 12VDC/24VDC @ 6A ho ACM8 board (e se nang matla a fokolang). AL1012ULACM - 12VDC @ 10A ho ACM8 board (e se nang matla a fokolang). AL1024ULACM - 24VDC @ 10A ho ACM8 board (e se nang matla a fokolang).
AC FAIL NC, C, NO	E sebedisetswa ho tsebisa tahlehelo ya matla a AC, mohlala, hokela sesebedisweng se utlwahalang kapa phanele ya alamo. Relay hangata e matlafatsoa ha matla a AC a le teng. Contact rating 1A @ 28VDC. AC kapa brownout failure e tlalehoa nakong ea motsotso o le mong oa ketsahalo. Ho lieha ho tlaleha ho fihlela lihora tse 6. seha "AC delay" jumper ebe o seta matla ho yuniti.
BAT FAIL NC, C, NO	E sebedisetswa ho bontsha boemo ba betri e tlase, mohlala, hokela phanele ya alamo. Relay hangata e matlafatsoa ha matla a DC a le teng. Contact rating 1A @ 28VDC. Betri e tlositsoeng e tlalehoa nakong ea metsotso e 5. Khokahano ea betri e tlaleheloa nakong ea motsotso o le mong. Tekanyetso e tlase ea betri: 12VDC output threshold set @ hoo e ka bang 10.5VDC (N/A bakeng sa AL1024ULACM), 24VDC output threshold set @ hoo e ka bang 21VDC (N/A bakeng sa AL1012ULACM).
+ BAT -	Lihokelo tsa betri tse emeng. AL400ULXB2, AL600ULXB le AL1012ULXB (Boto ea Phepelo ea Matla) boholo ba tefiso ea hajoale ke 0.7A. AL1024ULXB2 (Boto ea Phepelo ea Matla) boholo ba tefiso ea hajoale ke 3.6A.

ACM8 Access Power Controller

Terminal Taba	Mosebetsi/Tlhaloso
– Matla +	12VDC kapa 24VDC keno e tsoang botong ea phepelo ea motlakase.
– Taolo +	Li-terminals tsena li ka hokeloa phepelong ea motlakase e lekantsoeng ea UL e lekantsoeng ka thoko ho fana ka matla a ts'ebetso a ikhethileng bakeng sa ACM8 (li-jumpers J1 le J2 Li tlameha ho tlosoa).
KENYA YA TRIGGER 1 – INNPUT 8 IN, GND	Ho tsoa ho lisebelisoa tse tloaelehileng tse bulehileng le / kapa tse bulehileng tsa mokelli (kopo ea ho tsoa likonopo, ho tsoa li-PIR, joalo-joalo).
SEHLAHLWA 1 - PHELETSO 8 NC, C, NO, COM	Li-volts tse 12 ho isa ho tse 24 tsa AC/DC li baka liphetho tse laoloang: Fail-Safe [NC positive (+) & COM Negative (-)], E hlolehile-Sireletsehile [HA HO positi (+) & COM Negative (-)], Sephetho sa tlatsetso [C positive (+) & COM Negative (-)] (Ha u sebelisa polarity ea matla a AC ha ea lokela ho bonoa), NC, C, NO fetoha foromo "C" 5A 24VAC/VDC e fane ka lintlha tse omileng ha li-fuse li tlosoa. Mabitso a bonts'itsoeng a sa qalelle.
FACP INTERFACE T, + INNPUT –	Sehokelo sa Alarm ea Mollo se kenya letsoho ho tsoa ho FACP. Lisebelisoa tsa trigger li ka buloa ka tloaelo, hangata li koaloa ho tsoa ho potoloho ea FACP (Setšoantšo sa 4 ho isa ho 8, maqephe 9-10).
FACP INTERFACE NC, C, NO	Foromo "C" relay contact rated @ 1A 28VDC bakeng sa tlaleho ea alamo. (Sephetho sena ha se so hlahlojoe ke UL).

Setšoantšo se Tloaelehileng sa Kopo

Lisebelisoa tsa LED

Boto ea Phepelo ea Matla

LED		Boemo ba Phepelo ea Matla
Khubelu (DC)	Botala (AC)
ON	ON	Boemo bo tloaelehileng ba ts'ebetso.
ON	TLOA	Tahlehelo ea AC. Matla a ho fana ka betri e emeng.
TLOA	ON	Ha ho tlhahiso ea DC. Potoloho e khuts'oane kapa boemo ba ho tlala mocheso.
TLOA	TLOA	Ha ho tlhahiso ea DC.

Khubelu (Bat)	Boemo ba Battery
ON	Boemo bo tloaelehileng ba ts'ebetso.
TLOA	Betri e hlolehile/betri e tlase.

ACM8 Access Power Controller

LED	ON	TLOA
LED 1 – LED 8 (Khubelu)	Li-relay tse hlahisoang li matlafalitsoe.	Li-relay li feletsoe ke matla.
Trg (Tala)	Ho kenya FACP (boemo ba alamo).	FACP e tloaelehileng (boemo boo e seng alamo).

Setšoantšo sa 2 - ACM Series Configuration

TLHOKOMELISO: Fokotsa yuniti e matla pele u sebeletsa. Bakeng sa tšireletso e tsoelang pele khahlanong le mollo, likotsi li nkela fuse sebaka ka mofuta o tšoanang le litekanyetso.
TLHOKOMELISO: Libetri tse emang ka boikhethelo tse ka tjhajwang li tlameha ho ts'oana le matla a phano ea motlakasetage beha. Boloka lithapo tse lekanyelitsoeng matla li arohane le tse se nang matla. Sebelisa sebaka sa bonyane 0.25 ″.

• Ha ho hlokahala lintlha tsa Sehlopha sa 2 ho reka linomoro tsa mohlala: AL400ULACMCB, AL600ULACMCB, AL1012ULACMCB le AL1024ULACMCB

Hook-Up Diagrams

Setšoantšo sa 3 Ho hokahana ha boikhethelo ho sebelisa lisebelisoa tse peli (2) tse ikhethileng tsa phepelo ea motlakase

Setšoantšo sa 4 Polarity reversal input ho tloha FACP signaling circuit output (polarity e hlalosoa ka boemo ba alamo)

Setšoantšo sa 5 Ka tloaelo Bulehile: Non-Latching FACP kenya letsoho

Setšoantšo sa 6 Ka tloaelo Bula FACP Latching trigger input with reset (Sephetho sena ha se eso hlahlojoe ke UL)

Setšoantšo sa 7 Ho Koetsoe Ka tloaelo: Ho Kena ha FACP e sa Lateng

Setšoantšo sa 8 Hangata se Koetsoe: Latching FACP trigger input with reset (Sephetho sena ha se so hlahlojoe ke UL)

Leqephe la tšebetso la ho bala boholo ba betri ea AL1024ULACM

• A. AL1024ULACM tshebediso ya ka hare ya jwale (e emeng) ________ 0.35A
• B. Laola tšebeliso ea hona joale (e eme) __________ A
• C. Ho hlokahala nako ea ho ema (Lihora) ________ H
• D. Bokhoni ba betri bo hlokahalang bakeng sa ho ema (A+B)*C __________ AH
• E. AL1024ULACM tšebeliso ea matla ka hare (Alamo) __________ 0.35A
• F. Laola tšebeliso ea hona joale (Alamo) __________ A
• G. Nako ea alamo (Lihora, mohlalaample: 15 mets. = 0.25 Hora) (Alamo) __________ H
• H. Bokhoni ba betri bo hlokahalang bakeng sa Alamo (E+F)*G __________ AH
• I. Kakaretso e lekantsoeng ea matla a betri D+H __________ AH
• J. Bokhoni ba betri bo hlokahala I*1.8 (safety factor) __________ AH

Hlokomela: Sesebelisoa sa motlakase sa AL1024ULACM se etselitsoe ho sebetsa ka libeteri ho fihla ho 65AH. Ka kopo hlokomela, mola [I] ha oa tlameha ho feta 36AH. U tlameha ho fokotsa tšebeliso ea hona joale kapa nako ea ho ema e le hore u ikamahanye le litlhoko. Ho fumana boholo ba betri ka kopo, pota mohala [J] ho isa ho saese e tloaelehileng e haufi ea betri.

Kakaretso Dimensions

15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm)

• Altronix ha e ikarabelle bakeng sa liphoso leha e le life tsa typographical.
• 140 58th Street, Brooklyn, New York 11220 USA
• mohala: 718-567-8181
• fekse: 718-567-9056
• websebaka: www.altelengx.com
• lengolo-tsoibila: info@altronix.com
• Warranty ea bophelo bohle

Litokomane / Lisebelisoa

Altronix ACM Series Access Power Controllers ka Lisebelisoa tsa Matla [pdf] Tlhophiso Tataiso ACM Series Access Power Controllers with Power Supplies, ACM Series, Access Power Controllers with Power Suppliers, Power Controllers with Power Suppliers, Access Power Controllers, Power Controllers, Power Supplies Controllers, AL400ULACM, AL1012ULACM, AL600ULACM, AL1024ULACM

Litšupiso

• Bukana ea Mosebelisi