AliExpress ZK-KTD2 Trigger Cycle Timer Delay Controller

Tlhahisoleseding ya Sehlahiswa

Litlhaloso:

• Lebitso la Sehlahiswa: ZK-KTD2 Trigger Cycle Timer Delay Controller
• Nomoro ea Sehlahisoa: ZK-KTD2
• Sebetsa Voltage: Tlhaloso: DC 5.0V ~ 30V
• Mofuta oa ho qala: Konopo/PNP/NPN/High/Low Level Signal
• Letshwao la High Trigger: Tlhaloso: DC 3.0V ~ 24V
• Mofuta oa tlhahiso: Relay Switch Output (No voltage output)
• Mojaro (Boholo): DC 30V 10A kapa AC 250V 10A
• Mosebetsi oa Hona Joale: 50mA
• Quiscent Current: 20mA
• Hlahisa: 3Bit Red LED Display Screen
• Sebaka sa Mocheso oa Mosebetsi: -40 ~ 85°C
• Mongobo oa Mosebetsi: 5% -95%RH
• Boholo ba Mojule: 79*43*26mm

Litaelo tsa Tšebeliso ea Sehlahisoa

Nako ea Nako:
Nako ea nako ea ZK-KTD2 Trigger Cycle Timer Delay Controller e khethoa ke litlhophiso tsa nako ea ho lieha.

Tlhaloso ea Paramethara:

• OP: Ho lieha nako ea ho bulela
• CL: Ho lieha nako ea ho tima
• LOP: Palo ea lipotoloho. Nako ke makhetlo a 1-999. '—-' e bolela loop e se nang moeli.
• CLL: Bonyane bo tlase ba nako ea tieho e sa reroang. Sebaka se behiloeng ke 0.0 ~ 99.9 metsotsoana. Parameter ena ea CLL e sebelisoa feela bakeng sa mokhoa oa ho sebetsa oa P15.
• CHL: Boleng bo kaholimo ho nako ea tieho e sa reroang. Sebaka se behiloeng ke 0.0 ~ 99.9 metsotsoana. Paramethara ena ea CLH e sebelisoa feela bakeng sa mokhoa oa ho sebetsa oa P15. CLH e kholo ho feta CLL.

Mokhoa oa ho lieha ho sebelisa matla:
Mokhoeng oa ho lieha ho sebetsa ka Power-ON, ZK-KTD2 Trigger Cycle Timer Delay Controller e tla qala tieho ka mor'a hore matla a sebetse, ntle le tlhokahalo ea letšoao leha e le lefe le qalang.

• P00: Matla a BONAHALA 'me a tsoa a koalehile 'me a qale nako ea ho lieha CL. Ebe o bulela tlhahiso ka mor'a nako ea ho lieha CL. Example: Power ON -> TIMA -> Delay CL -> ON.
• P01: Bula 'me u bulele tlhahiso 'me u qale nako ea ho lieha OP. Ebe o tima tlhahiso kamora nako ea tieho OP. Example: Matla ON -> ON -> Delay OP -> TIMA.
• P02: Bula 'me u bulele tlhahiso 'me u qale nako ea ho lieha OP. Ebe o tima tlhahiso kamora nako ea tieho OP. Thibela nako ea tieho CL. Ebe o bulela tlhahiso ka mor'a nako ea ho lieha CL. 'Me joale loops ketso e ka holimo. Palo ea li-cycles (LOP) e ka behoa. Sehlahisoa se tla tima ka mor'a potoloho. Example: Power ON -> ON -> Delay OP -> OFF -> Delay CL -> cycles -> OFF.
• P03: Matla a BUA 'me tlhahiso e koetsoe' me u qale nako ea ho lieha CL. Ebe o bulela tlhahiso ka mor'a nako ea ho lieha CL. Tsoela pele ho ON bakeng sa nako ea ho lieha OP. Ebe o tima tlhahiso kamora nako ea tieho OP. 'Me joale loops ketso e ka holimo. Palo ea li-cycles (LOP) e ka behoa. Sephetho se tla tsoela pele ka mor'a potoloho. Example: Power ON -> OFF -> Delay CL -> ON -> Delay OP -> cycles -> ON.

Mokhoa oa Pulse Signal Trigger:
Ka Pulse Signal Trigger Mode, ZK-KTD2 Trigger Cycle Timer Delay Controller e tla qala ho lieha ka mor'a ho fumana letšoao la ho kenya letsoho.

• P04: Letšoao la ho kenya letsoho le phallo e BULE 'me u qale nako ea ho lieha OP. Ebe o tima tlhahiso kamora nako ea tieho OP. Ho qala hape nakong ea tieho ha hoa nepahala. Example: Trigger -> ON -> Delay OP -> TIMA.

LBH

• P: Ke eng e sebetsang voltagna mofuta oa "Trigger Cycle Timer Delay Controller" ea ZK-KTD2?
  Karolo ea ho sebetsatagsebaka sa e ke DC 5.0V ho 30V.
• P: Ke boima bofe bo boholo bo ka etsoang ke Taolo ea ho lieha ha nako ea "Trigger Cycle Cycle" ea ZK-KTD2?
  The ZK-KTD2 Trigger Cycle Timer Delay Controller e ka sebetsana le mojaro o moholo oa DC 30V 10A kapa AC 250V 10A.
• Q: Ke boholo bofe ba module ea ZK-KTD2 Trigger Cycle Timer Delay Controller?
  Boholo ba module ke 79mm x 43mm x 26mm.

Tlhaloso:
ZK-KTD2 ke Relay Switch Controller Trigger Delay Module e nang le Timer le Cycle function. E ka sebetsa ka mokhoa oa 16 oa mofuta oa mosebetsi o nang le lets'oao kapa ntle le leqhubu.

Likaroloana

1. Mefuta e 16 ea mesebetsi
2. Boemo bo Phahameng/Botlase kapa PNP/NPN seqhutsu sa letshwao
3. Motlakase oa ho kenya matla
4. Konopo switjha trigger
5. 2200W 10A Relay Driver
6. Ts'ehetso ea memori ea parameter
7. Ts'ehetsa mosebetsi oa puisano oa UART
8. Sehlahisoa se ikhethileng sa Optocoupler
9. Tšehetso e qobelloang ho emisa mosebetsi
10. Tšehetsa mokhoa oa ho boloka matla

Mekhahlelo

1. Lebitso la Sehlahiswa: ZK-KTD2 Trigger Cycle Timer Delay Controller
2. Nomoro ea Sehlahisoa: ZK-KTD2
3. Sebetsa Voltage: Tlhaloso: DC 5.0V ~ 30V
4. Mofuta oa ho qala: Konopo/PNP/NPN/High/Low Level Signal
5. Letshwao la High Trigger: Tlhaloso: DC 3.0V ~ 24V
6. Mofuta oa tlhahiso: Relay Switch Output (No voltage output)
7. Mojaro(Boholo): DC 30V 10A kapa AC 250V 10A
8. Mosebetsi oa Hona Joale: 50mA
9. Quiscent Current: 20mA
10. Hlahisa: 3Bit Red LED Display Screen
11. Boemo ba mocheso o sebetsang: -40℃~85℃
12. Mongobo oa Mosebetsi: 5% -95%RH
13. Boholo ba Mojule: 79*43*26mm

Nako ea nako

1. E lula e fetoha ho tloha metsotsoana e 0.1 ho isa ho metsotso e 999.
2. Kenya sebopeho sa li-setting ha o tobetsa konopo e khuts'oane ea 'STOP' ho sebopeho sa phetoho ea parametha(Flashing) ho khetha sebaka sa nako.
3. Ela hloko boemo boo ntlha ea decimal e tsamaeang ho eona ha konopo e tobetsoa.
4. Hlahisa 'XXX.' Ntlha ea ho qetela karolong ea ho qetela, nako ea nako ke metsotsoana e le 1 ~ 999 metsotsoana.
5. Bonts'a 'XX.X' Boemo ba decimal ho penultimate, sebaka sa nako ke metsotsoana e 0.1 ho isa ho metsotsoana e 99.9.
6. Hlahisa 'XXX' Sebaka sa decimal se bonesitsoe ka botlalo, nako ke motsotso o le mong ho isa ho metsotso e 1.
7. Bakeng sa mohlalaample, haeba u batla ho seta OP ho metsotsoana e 3.2, tsamaisa ntlha ea decimal ho ea sebakeng sa penultimate, Screen e tla bonts'a '03.2'
8. Liparamente tsa OP le CL lia tšoana ka mokhoa o fapaneng oa mosebetsi.
9. E tla bonts'a OP(CL, LOP) le nako ea ho lieha e tsamaellanang ka konopo e khuts'oane ea SET sebopehong se seholo sa ponts'o.
10. E mpa e bonts'a OP le nako e tsamaellanang ea ho lieha ka mokhoa oa P1 ka konopo e khuts'oane ea SET sebopehong se seholo sa ponts'o.
11. Tobetsa hakhutšoanyane konopo ea 'SET' ho ponts'o e tloaelehileng ho botsa OP, CL, LOP boleng ka ho fapanyetsana.

Tlhaloso ea Paramethara:

1. OP: Ho lieha nako ea ho bulela;
2. CL: Ho lieha nako ea ho tima;
3. LOP: Palo ea lipotoloho. Range ke 1-999tims. '—-' e bolela loop e se nang moeli.
4. CLL: Bonyane bo tlase ba nako ea tieho e sa reroang. Sebaka se behiloeng ke 0.0 ~ 99.9 metsotsoana. Paramethara ena ea CLL e tla sebelisoa feela bakeng sa mokhoa oa ho sebetsa oa P15.
5. CHL: Boleng bo kaholimo ho nako ea tieho e sa reroang. Sebaka se behiloeng ke 0.0 ~ 99.9 metsotsoana. Paramethara ena ea CLH e tla sebelisoa feela bakeng sa mokhoa oa ho sebetsa oa P15. CLH e kholo ho feta CLL.

MOSOTHO

Mokhoa oa ho lieha ho sebetsa:

1. ZK-KTD2 e tla qala ho lieha ka mor'a hore motlakase o bulehe. Mokhoa ona ha o hloke ho kenya lets'oao le leng la ho qala. Phepelo ea matla ke letšoao la ho qala.
2. P00: Matla a BONAHALA 'me a tsoa a koalehile 'me a qale nako ea ho lieha CL. Ebe o bulela tlhahiso ka mor'a nako ea ho lieha CL. Mohlala: Matla HO ON-> Off->Delay CL-> ON.
3. P01: Bula 'me u bulele tlhahiso 'me u qale nako ea ho lieha OP. Ebe o tima tlhahiso kamora nako ea tieho OP. Mohl. Matla HO ON-> ON->Delay OP-> Off.
4. P02: Bula 'me u bulele tlhahiso 'me u qale nako ea ho lieha OP. Ebe o tima tlhahiso kamora nako ea tieho OP. Thibela nako ea tieho CL. Ebe o bulela tlhahiso ka mor'a nako ea ho lieha CL. 'Me joale loops ketso e ka holimo. Palo ea li-cycles (LOP) e ka behoa. Sehlahisoa se tla tima ka mor'a potoloho. Mohl. Matla HO ON->ON->Delay OP->OFF->Delay CL->cycles->OFF.
5. P03: Matla a BUA 'me tlhahiso e koetsoe' me u qale nako ea ho lieha CL. Ebe o bulela tlhahiso ka mor'a nako ea ho lieha CL. Tsoela pele ho ON bakeng sa nako ea ho lieha OP. Ebe o tima tlhahiso kamora nako ea tieho OP. 'Me joale loops ketso e ka holimo. Palo ea li-cycles (LOP) e ka behoa. Sephetho se tla tsoela pele ka mor'a potoloho. Mohl. Power ON-> Off->Delay CL->ON->Delay OP->cycles->ON.

Mokhoa oa Pulse Signal Trigger:

1. ZK-KTD2 e tla qala ho lieha ka mor'a ho kenya letsoho. Mokhoa ona o hloka lets'oao la ho kenya letsoho ka mor'a ho fana ka matla a ho sebetsa.
2. P04: Letšoao la ho kenya letsoho le phallo e BULE 'me u qale nako ea ho lieha OP. Ebe o tima tlhahiso kamora nako ea tieho OP. Trigger hape ha e sebetse nakong ea ho lieha. Mohlala: Trigger-> ON-> Liehe OP-> TIMA.
3. P05: Letšoao la ho kenya letsoho le phallo e BULE 'me u qale nako ea ho lieha OP. Ebe o tima tlhahiso kamora nako ea tieho OP. Qala ho lieha ha OP haeba e ka qala hape nakong ea ho lieha. Mohlala: Trigger-> ON-> Liehe OP-> TIMA.
4. P06: Letšoao la ho kenya letsoho le phallo e BULE 'me u qale nako ea ho lieha OP. Ebe o tima tlhahiso kamora nako ea tieho OP. Emisa tieho 'me u koale tlhahiso ha e ka qala hape nakong ea tieho. Mohlala: Trigger-> ON-> Liehe OP-> TIMA.
5. P07: Letšoao la ho kenya letsoho le phallo li koale 'me u qale nako ea ho lieha CL. Ebe o bulela tlhahiso ka mor'a nako ea ho lieha CL. Mohlala: Trigger-> Off->Delay CL-> ON.
6. P08: Lets'oao la ho kenya letsoho le phallo, TLOA 'me u qale nako ea ho lieha CL. Ebe o bulela tlhahiso ka mor'a nako ea ho lieha CL. Tsoela pele ho ON bakeng sa nako ea ho lieha OP. Ebe o tima tlhahiso kamora nako ea tieho OP. Trigger hape ha e sebetse nakong ea ho lieha. Mohlala: Trigger-> Off->Delay CL->ON->Delay OP-> Off.
7. P09: Lets'oao la ho kenya letsoho le phallo, TLOA 'me u qale nako ea ho lieha CL. Ebe o bulela tlhahiso ka mor'a nako ea ho lieha CL. Tsoela pele ho ON bakeng sa nako ea ho lieha OP. Ebe o tima tlhahiso kamora nako ea tieho OP. Qala ho lieha ha OP haeba e ka qala hape nakong ea ho lieha. Mohlala: Trigger-> Off->Delay CL->ON->Delay OP-> Off.
8. P10: Lets'oao la ho kenya letsoho le phallo, TLOA 'me u qale nako ea ho lieha CL. Ebe o bulela tlhahiso ka mor'a nako ea ho lieha CL. Tsoela pele ho ON bakeng sa nako ea ho lieha OP. Ebe o tima tlhahiso kamora nako ea tieho OP. 'Me joale loops ketso e ka holimo. Palo ea li-cycles (LOP) e ka behoa. Sephetho se tla tsoela pele ka mor'a potoloho. Emisa tieho 'me u bulele tlhahiso haeba u ka qala hape nakong ea lipotoloho. Mohlala: Trigger-> Off->Delay CL->ON->Delay OP-> cycles-> ON.
9. P11: Letšoao la ho kenya letsoho le phallo e BULE 'me u qale nako ea ho lieha OP. Ebe o tima tlhahiso kamora nako ea tieho OP. Thibela nako ea tieho CL. Ebe o bulela tlhahiso ka mor'a nako ea ho lieha CL. 'Me joale loops ketso e ka holimo. Palo ea li-cycles (LOP) e ka behoa. Sehlahisoa se tla tima ka mor'a potoloho. Emisa tieho 'me u koale tlhahiso ha u ka qala hape nakong ea lipotoloho. Mohlala: Trigger->ON->Delay OP->OFF->Delay CL->cycles->OFF.
10. P12: Letšoao la ho kenya letsoho le phallo e BULE 'me u qale nako ea ho lieha OP. Ebe o tima tlhahiso kamora nako ea tieho OP. Thibela nako ea tieho CL. Ebe o bulela tlhahiso ka mor'a nako ea ho lieha CL. 'Me joale loops ketso e ka holimo. Palo ea li-cycles (LOP) e ka behoa. Sehlahisoa se tla tima ka mor'a potoloho. Trigger hape ha e sebetse nakong ea lipotoloho. Mohlala: Trigger->ON->Delay OP->OFF->Delay CL->cycles->OFF.

Boloka Mokhoa oa ho Qala oa Letšoao:

1. Mokhoa ona o hloka ho boloka lets'oao la ho kenya letsoho. Boemo ba tlhahiso le bona bo tla fetoha ha lets'oao la ho kenya letsoho le tlosoa,.
2. P13: Boloka lets'oao la ho kenya letsoho 'me u bulele tlhahiso. Ebe o qala nako ea ho lieha OP haeba o tlosa sehlomathisi sa ho kenya. Ebe o tima tlhahiso kamora nako ea tieho OP. Emisa tieho ebe o bulela tlhahiso ha e ka qala hape nakong ea tieho.
3. P14: Boloka lets'oao la ho kenya letsoho 'me u koale tlhahiso. Ebe o qala nako ea ho lieha CL haeba o tlosa sebatli sa ho kenya. Ebe o bulela tlhahiso ka mor'a nako ea ho lieha CL. Emisa tieho 'me u koale tlhahiso ha e ka qala hape nakong ea tieho.

Mokhoa oa ho lieha ho sa feleng:

1. P15: Letšoao la ho kenya letsoho le sephetho li koale 'me u qale nako ea ho lieha. Nako ea ho lieha pakeng tsa CLL le CLH. Ebe o bulela tlhahiso kamora nako ea ho lieha CLL~CLH. Mokhoa ona o ka boela oa beha potoloho ea mosebetsi oa PWM ho tloha 20%,25%,30%,35% ho 100% ho 600Hz ka parameter SP. (Nako ea tieho ke boleng bo sa reroang pakeng tsa CLL le CLH. Boemo ba bona ba ho seta ke 0.0~99.9mtsotsoana 'me CLH e feta CLL.) Mohl. Trigger->OFF->Delay->ON.

Beha mehato

1. Netefatsa mokhoa oa ho sebetsa pele o qala ho seta mokhoa le liparamente.
2. 'Ne u tobetse SET Konopo hoo e ka bang metsotsoana e 2 kenya ho khetha mokhoa oa ho sebetsa.
3. Tobetsa konopo ea Holimo le Tlase ho fetola mokhoa oa ho sebetsa P00~P015.
4. Tobetsa konopo ea SET ho beha boleng ba paramethara bakeng sa mokhoa o khethiloeng oa mosebetsi joalo ka mokhoa oa mosebetsi oa P03.
5. Paramethara ea pele ea OP e tla benya hoo e ka bang 2second ebe e bonts'a boleng ba parametha.
6. Tobetsa konopo ea STOP ho tsamaisa ntlha ea decimal le ho seta nako ea ho lieha.
7. Tobetsa konopo ea UP le Down ho seta boleng ba paramethara ea OP.
8. Tobetsa konopo ea SET ho beha boleng ba paramethara ea bobeli CL. Ebe u beha moeli oa nako le boleng ba parameter joalo ka mokhoa o ts'oanang.
9. Tobetsa konopo ea SET ho beha boleng ba paramethara ea boraro LOP. Ebe u beha parameter joalo ka mokhoa o ts'oanang.
   Hlokomela: '—-' e bolela loop e se nang moeli.
10. Bakeng sa mokhoa oa mosebetsi oa P15 mokhoa o behiloeng o tšoana le oa CLL, CLH le SP.
    Hlokomela: Nako ea ho lieha ke metsotsoana e 0.0~99.9 ka mokhoa ona.
11. Tobetsa SET Konopo hoo e ka bang 2second ho boloka paramethara le ho tsoa ka mokhoa oa sete ho qala mosebetsi o tloaelehileng.

Likarolo tse Eketsehileng:

1. Mosebetsi oa ho robala oa Auto: boloka konopo ea 'STOP' hoo e ka bang 2second ka har'a sehokelo se tloaelehileng sa ho bulela kapa ho tima ts'ebetso ea boroko ea auto.
   1. CL: BUA auto sleep function.Skrine se tla itima ka ho iketsa haeba ho se na opereishene nakong ea metsotso e 3. E ka tsosoa ka likonopo life kapa life.
   2. Od: TLOA tšebetso ea ho robala ka boits'oaro.
2. E nolofalitsoe/e holofalitsoe ka konopo ea tobetsa STOP:
   1. BULELA: Tlhahiso e nolofalitsoeng nakong ea tieho OP.
   2. TIMA: Sephetho se koetsoeng. Module ha e khone ho hlahisa lets'oao lefe kapa lefe ka mokhoa ona.
3. Ha e sebetse ke ponts'o '000' eo ho seng ntlha ea decimal e bonts'itsoeng. mohlala ho felisa boemo ba ho sebetsa ba cyclic.

Sebelisa Mehato:

1. Connect right work voltage ho tsoa ho terminal ea ho kenya.
2. Beha mokhoa oa ho sebetsa le boleng ba parameter.
3. Tlosa phepelo ea motlakase mosebetsing.
4. Kopanya mojaro le mojaro voltage, lets'oao la ho qala ha ho hlokahala.
5. Hokela hape phepelo ea motlakase.
6. Qala mosebetsi o tloaelehileng ka lets'oao la ho qala kapa ntle le lona ka mokhoa o khethiloeng oa ho sebetsa.

UART Control Protocol

Litlhophiso tsa Lipuisano tsa UART le Parameter
Che.	Paramethara		Boleng
1	Sekhahla sa Baud		9600bps
2	Lintlha tsa data		8 bit
3	Emisa hanyane		1 bit
4	Sheba hanyane		ha ho letho
5	Taolo ea phallo		ha ho letho
6	Protocol		MODBUS-RTU
7	Khoutu ea tšebetso		0x03,0x06,0x10 (Tsehetsa khoutu ea ts'ebetso e meraro feela)
8	Aterese ea sesebelisoa		0x01~0xFF(Aterese ea kamehla ke 0x01)
Che.	Taelo	Mosebetsi	Beha Range	Ea kamehla	Li-byte	Bala/Ngola	Ngolisa Aterese
1	Addr	Beha aterese ea sesebelisoa	0x01 ~ 0xFF	0x01	2	R/W	0000H
2	Matha	Boemo ba Mosebetsi	0: ea sebetsa	—-	2	R/W	0001H
			1: Emisa Mosebetsi
3	ROBALA	Noble/Thibela boemo ba ho robala	0: Tlosa	—-	2	R/W	0002H
			1: nolofalletsa
4	MOKHOA	Seta mokhoa oa ho sebetsa	0x00~0x0F	—-	2	R/W	0003H
5	OP	Ho lieha nako bakeng sa OP	0-999	—-	2	R/W	0004H
6	OP UNITI	Beha yuniti ea nako ea ho lieha bakeng sa OP	0:ea bobeli	—-	2	R/W	0005H
			1:0.1 Ea bobeli
			2:Motsotso
7	CL	Ho lieha nako bakeng sa OL	0x00~0x0F	—-	2	R/W	0006H
8	TLHOKOMELISO	Beha nako ea ho lieha	0:ea bobeli	—-	2	R/W	0007H

		unit bakeng sa OL	1:0.1 Ea bobeli
			2:Motsotso
9	LP	Beha linako tsa loop	1 ~ 999: Linako tse lekanyelitsoeng	—-	2	R/W	0008H
			—:Linako tse sa feleng
10	CLL	Beha boleng ba Min ea tieho e sa reroang.	0-99.9s	—-	2	R/W	0009H
11	CLH	Beha Boleng bo phahameng ba tieho e sa reroang.	0-99.9s	—-	2	R/W	000AH
12	SP	Beha potoloho ea mosebetsi oa PWM	20%~100%	—-	2	R/W	EA-000BH
13	TRGI-GER	Letšoao la ho kenya letsoho	Bakeng sa P04~P15	—-	2	W	000CH

Hlokomela:

1. Ke sehlahisoa sa relay switch, ka hona ha se khone ho hlahisa voltage. Mojaro o boetse o hloka ho hokahanngoa le boima ba moroalotage.
2. E tla bonts'a '000' haeba mosebetsi o emisa. E bonts'a ntlha ea decimal ha e sebetsa.
3. Ka kopo bala tšebeliso ea libuka le tlhaloso pele u sebelisa.

Kopo

1. Ho lieha ho fetoha
2. Counter
3. Sistimi ea taolo ea phihlello
4. Phetoho ea potoloho ea koloi
5. Motor
6. The valve electromagnetic
7. Letlapa le khanyang

Sephutheloana:

1. 1pcs ZK-KTD2 Trigger Cycle Timer Delay Controller

Rea u amohela ho www.amazon.com/shops/icstation | Ikopanye le rona ho icstation@hotmail.com

Litokomane / Lisebelisoa

AliExpress ZK-KTD2 Trigger Cycle Timer Delay Controller [pdf] Litaelo ZK-KTD2 Trigger Cycle Timer Delay Controller, ZK-KTD2, Trigger Cycle Timer Delay Controller, Cycle Timer Delay Controller, Timer Delay Controller, Delay Controller, Controller

Litšupiso

• Bukana ea Mosebelisi