Tataiso ea mosebelisi ea AiM
Solo 2/Solo 2 DL, EVO4S
and ECULog kit for Suzuki
GSX-R 600 (2004-2023)
GSX-R 750 (2004-2017)
GSX-R1000 ho tloha 2005
GSX-R 1300 (2008-2016)
Lokolla 1.01
Mehlala le lilemo
Bukana ena e hlalosa mokhoa oa ho hokahanya Solo 2 DL, EVO4S le ECULog ho yuniti ea taolo ea libaesekele (ECU).
Mefuta e lumellanang le lilemo ke:
| • GSX-R 600 | 2004-2023 |
| • GSX-R 750 | 2004-2017 |
| • GSX-R 1000 | ho tloha ka 2005 |
| • GSX-R 1300 Hayabusa Gen. 2 | 2008-2016 |
Tlhokomeliso: bakeng sa mehlala / lilemo tsena AiM e khothalletsa hore u se ke ua tlosa dash ea stock. Ho etsa joalo ho tla tima tse ling tsa mesebetsi ea libaesekele kapa taolo ea polokeho. AiM Tech Srl e ke ke ea jara boikarabello bakeng sa litlamorao life kapa life tse ka hlahisoang ke ho nkeloa sebaka ha sehlopha sa mantlha sa lisebelisoa.
Likahare tsa Kit le linomoro tsa karolo
AiM developed a specific installation bracket for Solo 2/Solo 2 DL that fits some bike models only – specified in the following paragraph – and a CAN connection cable to the ECU for Solo 2 DL, EVO4S and ECULog.
2.1 Bracket bakeng sa Solo 2/Solo 2 DL
Part number of Solo 2/Solo 2 DL installation bracket for Suzuki GSX-R – shown below – is: X46KSSGSXR.
Setsi sa ho kenya se na le:
- 1 bracket (1)
- 1 Allen screw with rounded head M8x45mm (2)
- 2 Allen screws with flat head M4x10mm (3)
- 1 toothed washer (4)
- 1 rubber dowel (5)
Lemoha ka kopo: insta lation bracket does not fit Suzuki GSX-R 1000 bikes from 2005 to 2008 nor Suzuki GSX-R 1300 Hayabusa Gen. 2 from 2008 to 2016 included.
2.2 AiM cable for Solo 2 DL, EVO4S and ECULog
Part number of connection cable for Suzuki GSX-R– shown below – is: V02569140.
Setšoantšo se latelang se bontša leano la ho haha cable.
2.3 Solo 2 DL kit (thapo ea AiM + bracket)
Bracket ea ho kenya Solo 2 DL le thapo ea khokahano bakeng sa Suzuki GSX-R le eona e ka rekoa hammoho le karolo ea nomoro: V0256914CS. Ka kopo hopola hore borakete ha e lekane Suzuki GSX-R 1000 ho tloha 2005 ho isa 2008 kapa Suzuki GSX-R 1300 Hayabusa Gen. 2 ho tloha 2008 ho isa 2016.
Khokahano ea Solo 2 DL, EVO4S le ECULog
To connect Solo 2 DL, EVO4S and ECULog to the bike ECU use the white diagnostic connector placed under the bike seat and shown here below.
Lifting the bike seat the ECU diagnostic connector shows a black rubber cap (shown bottom in the image here on the right): remove it and connect AiM cable to Suzuki connector.
Configuring with RaceStudio 3
Before connecting AiM device to the bike ECU set all functions using AiM RaceStudio 3 software. The parameters to set in the device configuration section (“ECU Stream” tab) are:
- ECU Manufacturer: “Suzuki”
- ECU Model: (RaceStudio 3 only)
o “SDS_protocol” for all models except for Suzuki GSX-R 1000 from 2017
o “SDS 2 Protocol” for Suzuki GSX-R 1000 from 2017
Suzuki protocols
Liteishene tse amoheloang ke lisebelisoa tsa AiM tse hlophisitsoeng ka liprothokholo tsa Suzuki li fetoha ho latela protocol e khethiloeng.
5.1 “Suzuki – SDS_Protocol”
Channels received by AiM devices configured with “Suzuki – SDS_Protocol” protocol are:
| LEBITSO LA KHALE | MOSEBETSI |
| SDS RPM | RPM |
| SDS TPS | Boemo ba mantlha ba throttle |
| SDS MOKHALE | Lisebelisoa tse kopanetsoeng |
| SDS BATT VOLT | Phepelo ea betri |
| SDS CLT | Mocheso oa mocheso oa enjene |
| SDS IAT | Batla mocheso oa moea |
| SDS MAP | Khatello ea moea e mengata |
| SDS BAROMA | Khatello ea barometric |
| SDS BOOST | Matlafatsa khatello |
| SDS AFR | Air/Fuel ratio |
| SDS NEUT | Phetoho e sa nke lehlakore |
| SDS CLUT | Khaba ea li-clutch |
| SDS FUEL1 pw | Ente ea mafura 1 |
| SDS FUEL2 pw | Ente ea mafura 2 |
| SDS FUEL3 pw | Ente ea mafura 3 |
| SDS FUEL4 pw | Ente ea mafura 4 |
| SDS MS | Mokhethi oa mokhoa |
| SDS XON ON | XON switch |
| SDS PAIR | PAIR ventilation system |
| SDS IGN ANG | Tsela ea ho khantša |
| SDS STP | Boemo ba bobeli ba throttle |
Tekanyetso ea tekheniki: ha se liteishene tsohle tsa data tse boletsoeng ho template ea ECU tse netefalitsoeng bakeng sa mofuta o mong le o mong oa moetsi kapa mofuta o mong; tse ling tsa likanale tse boletsoeng ke tsa mohlala le tsa selemo, ka hona li kanna tsa se sebetse.
5.2 “Suzuki – SDS 2 Protocol”
Channels received by AiM devices configured with “Suzuki – SDS 2 Protocol” protocol are:
| LEBITSO LA KHALE | MOSEBETSI |
| SDS RPM | RPM |
| SDS LEbelo R | Lebelo le ka morao |
| SDS LEbelo F | Lebelo la lebili le ka pele |
| SDS MOKHALE | Lisebelisoa tse kopanetsoeng |
| SDS BATT VOLT | Matla a betritage |
| SDS CLT | Mocheso oa mocheso oa enjene |
| SDS IAT | Batla mocheso oa moea |
| SDS MAP | Khatello ea moea e mengata |
| SDS BAROMA | Khatello ea barometric |
| SDS FUEL1 msx10 | Ente ea mafura 1 |
| SDS FUEL2 msx10 | Ente ea mafura 2 |
| SDS FUEL3 msx10 | Ente ea mafura 3 |
| SDS FUEL4 msx10 | Ente ea mafura 4 |
| SDS IGN AN 1 | Ignition Angle 1 |
| SDS IGN AN 2 | Ignition Angle 2 |
| SDS IGN AN 3 | Ignition Angle 3 |
| SDS IGN AN 4 | Ignition Angle 4 |
| SDS TPS1 V | TPS1 voltage |
| SDS TPS2 V | TPS2 voltage |
| SDS GRIP1 V | Grip1 voltage |
| SDS GRIP2 V | Grip2 voltage |
| SDS SHIFT SENSELE | Shift sensor |
| SDS TPS1 | Boemo ba mantlha ba throttle |
| SDS TPS2 | Boemo ba bobeli ba throttle |
| SDS GRIP1 | Grip1 boemo |
| SDS GRIP2 | Grip2 boemo |
| SDS SPIN RATE | Wheel spin rate (TC: off) |
| SDS SPIN RT TC | Wheel spin rate (TC: on) |
| SDS DH COR AN | Dashspot correction angle |
Tlhokomeliso ea tekheniki: ha se liteishene tsohle tsa data tse boletsoeng ho template ea ECU tse netefalitsoeng bakeng sa mofuta o mong le o mong oa moetsi kapa mofuta o mong; tse ling tsa likanale tse thathamisitsoeng ke tsa mohlala le tsa selemo, ka hona li kanna tsa se sebetse.
The following channels work only if the system is connected to a Yoshimura ECU:
- SDS LEbelo F
- SDS SPIN RATE
- SDS SPIN RT TCC
- SDS DH COR AN
Litokomane / Lisebelisoa
 |
AiM Solo 2 DL GPS Lap Timer With ECU Input [pdf] Bukana ea Mosebelisi Suzuki GSX-R 600 2004-2023, GSX-R 750 2004-2017, GSX-R1000 from 2005, GSX-R 1300 2008-2016, Solo 2 DL GPS Lap Timer With ECU Input, Solo 2 DL, GPS Lap Timer With ECU Input, ECU Input |