Motsamaisi oa Monyako oa Aeotec Garage.
Aeotec Garage Door Controller e entsoe ka matla ho sebelisa mabone a hoketsoeng ka motlakase Z-Wave Hape. E tsamaisoa ke Aeotec's Gen5 theknoloji. U ka fumana ho eketsehileng ka Motsamaisi oa Monyako oa Garage ka ho latela sehokelo seo.
Ho bona hore na molaoli oa Garage Door o tsejoa hore o tsamaellana le sistimi ea hau ea Z-Wave kapa che, ka kopo sheba ea rona Papiso ea heke ea Z-Wave lethathamo. The litlhaloso tsa tekheniki ea Garage Door Controller e ka ba viewed ho sehokelo seo.
.
Tseba Molaoli oa Hao oa Garage.
Likahare tsa sephutheloana:
1. Molaoli oa Monyako oa Garage. 2. Sensor.
3. Adapter ea 5V DC.
4. Thapo ea USB.
5. Fetola Cable (× 2).
6. Sekhahla (× 6).
7. Back Plate Plate.
8. Fast Wiring Clip (× 2). 9. Theipi e mahlakore a mabeli.
Lintlha tsa bohlokoa tsa polokeho.
Ka kopo bala sena le litataiso tse ling tsa lisebelisoa ka hloko. Ho hloleha ho latela likhothaletso tse boletsoeng ke Aeotec Limited ho ka ba kotsi kapa ha baka tlolo ea molao. Moetsi, morekisi, morekisi, le / kapa morekisi a ke ke a jara boikarabello bakeng sa tahlehelo kapa tšenyo e bakiloeng ke ho se latele litaelo tse bukeng ena kapa lisebelisoa tse ling.
Garage Door Controller e etselitsoe ts'ebeliso ea ka tlung libakeng tse ommeng feela. Se ke oa sebelisa ho damp, mongobo, le / kapa libaka tse metsi.
E na le likarolo tse nyane; suthela hole le bana.
Ho qala ka potlako.
1. Matla ho molaoli oa monyako oa Garage.
Matlafatsa molaoli oa monyako oa Garage ka ho hokela Adapter ea 5V DC ho kenyelletso.
Hona joale kaha Garage Door Controller ea hau e sebelisoa, o tla bona Network LED e panya butle. Ha marang-rang a LED a ntse a panya, sena se supa hore Garage Door Controller e ikemiselitse ho kenyelletsoa marang-rang a Z-Wave.
2. Kenya / kenyelletsa / hokahanya molaoli oa hau oa Garage Door ho netweke ea Z-Wave.
Haeba u sebelisa heke e teng (ke hore. Vera, Smartthings, ISY994i ZW, Fibaro, jj):
U kanna ua hloka ho sheba mokhoa oa heke ea hau ea ho kenyelletsa lisebelisoa haeba u sa tsebe ho kopanya sesebelisoa sa Z-Wave.
1.Kenya heke ea hau ea mantlha ea Z-Wave ho li-mode tse peli, heke ea hau ea Z-Wave e lokela ho netefatsa hore e emetse ho kenya sesebelisoa se secha
2. Tobetsa konopo ea Z-Wave ho Molaoli oa Monyako oa Garage. LED ho Garage Door Controller e tla hadima kapele, e lateloe ke LED e tiileng bakeng sa metsotsoana e 1-2 bakeng sa kenyelletso e atlehileng.
Haeba u sebelisa Z-Stick:
1. Hokela 5V DC Adapter ho Garage Door Controller. Network ea eona ea LED e tla qala ho panya.
2. Haeba Z-Stick ya hao e hoketswe keiting kapa khomphuteng, e lokolle.
3. Nka Z-Stick ea hao ho Garage Door Controller ea hau.
4. Tobetsa konopo ea khato ho Z-Stick ea hau.
5. Tobetsa konopo ea Z-Wave ho Garage Door Controller.
6. Haeba Garage Door Controller e hokahane ka katleho le netweke ea hau ea Z-Wave, Network ea eona ea LED ha e sa tla hlola e panya.
7. Haeba khokahano e ne e sa atleha 'me Network LED e ntse e tsoela pele ho panya, pheta mehato e kaholimo.
8. Tobetsa konopo ea ketso ho Z-Stick ho e ntša ka mokhoa oa ho kenyelletsa.
Haeba u sebelisa Minimote:
1. Hokela 5V DC Adapter ho Garage Door Controller. Network ea eona ea LED e tla qala ho panya.
2. Nka Minimote ea hau ho Garage Door Controller ea hau.
3. Tobetsa konopo e kenyelletsang ho Minimote ea hau.
4. Tobetsa konopo ea leqhubu la Z ho Garage Door Controller ea hao.
5. Haeba Garage Door Controller e hokahane ka katleho le netweke ea hau ea Z-Wave, Network ea eona ea LED ha e sa tla hlola e panya. Haeba khokahanyo e sa atleha 'me Network LED e ntse e tsoela pele ho panya, pheta mehato e kaholimo.
Ka Garage Door Controller ea hau e se e sebetsa e le karolo ea lehae la hau le bohlale, o tla khona ho e hlophisa ho tsoa ho software ea taolo ea lapeng kapa ts'ebeliso ea mohala. Ka kopo sheba tataiso ea hau ea software bakeng sa litaelo tse nepahetseng mabapi le ho lokisa Garage Door Controller litlhoko tsa hau.
Teko ea Alamo (kamora ho parola marang-rang a hau)
Sistimi ea sebui ke 105dB, o ka lekola melumo ea eona le li-setting tsa molumo ka ho tobetsa "Button-" kapa "Button +" ka nako e telele ho qala liteko tsa molumo, moo ho tobetsa le ho ts'oara "Button +" ho tla fetohela molumo o latelang ebe o tobetsa le ho ts'oara "Button - ”e tla fetohela modumong o fetileng. Ha molumo o ntse o letsa, o ka tlanya "Button-" ho fokotsa molumo ha "Button +" e tla eketsa molumo. Sena se tla u thusa ho lekanya mohopolo oa hore na u ka rata ho hlophisa li-setting tsa hau joang bakeng sa ho bula / ho koala / ho sa tsejoe / ho koaloa maemo a alamo.
Kenya 'mele oa hau Garage Door Controller.
TEMOSO - HO Fokotsa Likotsi Tsa Kotsi Kapa Lefu:
FUMANA LITLHAKU TSA TAOLO
a) KA NTLE HO PONO EA MONYAKO;
b) BOPHELONG BO Bonyane ba 1.53 M (5 FT) BANA BA BANYANE HA BA KA FIHLELA; LE
c) TSOA MABAPI LE LINTHO TSOHLE TSE SENANG TSA Monyako.
Taolo ea Monyako oa Garage e tlameha ho kengoa ka tlung ea hau le pela monyako oa karache. E ke ke ea kenngoa kantle lintlheng tse kang pula le lehloa.
1. Sebelisa lisurufu tse 20mm tse fanoeng ho e khokhothela holim'a bokahare boo u bo batlang.
2. Hokela likhoele tse 2 tsa switch switch ho switch switcher 1 le 2 ho Garage Door Controller, ebe u sebelisa Fast Wiring Clip ho hokela li-switch switch tsa 2 ho li-motor switch cable, bona setšoantšo se ka tlase:
Hlokomela: Fast Wiring Clip e hloka ho sebelisoa ka lisebelisoa. Ha Cable switch le Motor switch Cable li hoketsoe ka Fast Wiring Clip, o tla hloka ho sebelisa lisebelisoa ho koalaamp Fast Wiring Clip, bona setšoantšo se kaholimo.
3. Joale notlela molaoli oa Garage monyako oa Back Mount Plate ka ho sotha Garage Door Controller.
Ho kenya Sensor monyakong oa Garage ea hau.
1. Tobetsa o tšoare konopo ea Latch ho notlolla poleiti:
2. Hula lakane e sireletsang lintho tse sireletsang, joale o tla bona Sensor LED blink hang ho bontša hore e bonesitsoe.
3. Lokisa poleiti ea hau ea ho kenya lisebelisoa ho monyako oa garage.
Lepolesa la sensor le lokela ho kenngoa kaholimo ho monyako oa karache (ka letsohong le letšehali, le bohareng kapa ka ho le letona). Joale khokhothela poleiti ea hau ea kutlo holimo. Poleiti ea hau e hokeloang e ka hokelloa ho sebelisoa lisurufu kapa theipi e nang le mahlakore a mabeli.
Haeba u sebelisa li-screws, hokela poleiti e hokeloang ka holim'a eona ka li-screws tse peli tsa 20mm tse fanoeng.
Haeba u sebelisa tepi e nang le mahlakore a mabeli, hlakola bokaholimo bo hloekileng ka oli kapa lerōle le nang le papatsoamp thaole. Ha bokaholimo bo omme ka ho felletseng, ebola lehlakore le leng la theipi hape ebe oe hokela karolong e tsamaellanang le eona ka lehlakoreng le ka morao la poleiti e ntseng e hola.
U ka khetha tsela e 'ngoe le e' ngoe ho tsoa mehahong ena e 2 e kaholimo. Re hloka feela ho hlokomela hore na mocheso oa tikoloho oa lemati la garage o ka tlase ho -5 C, re khothaletsa ho khetha tsela ea pele (re sebelisa lisurufu ho maneha poleiti e ntseng e hola) e ka tsitsang haholoanyane.
4. Notlela Sensor ea hau poleiting e ntseng e eketseha.
Tobetsa o tšoare konopo ea Latch, ebe o sutumelletsa Sensor poleiting e ntseng e hola.
Motsamaisi oa Teko ea Garage ea Teko.
Kamora ho qeta methati eohle ea ho kenya, o ka hloka ho leka Garage Door Controller ea hau ho bona hore na e kentsoe ka katleho. O ka kenya ts'ebetsong sena ka ho tobetsa konopo e khuts'oane ho switch ea Door ea Garage. Ha o tobetsa konopo ea switch, o tla bona alamo ea LED e panya ebe o letsetsa alamo molumo. Kamora metsotsoana e ka bang 5, monyako oa karache o tla ea boemong bo bulehileng kapa bo koetsoeng ka botlalo. Haeba o tobetsa konopo ea switch switch hape, monyako oa garage o tla emisa hanghang. Haeba ho se joalo, ka kopo sheba kapa u phete mehato e kaholimo.
Sensor e sekametseng ka bobeli ho Garage Door Controller ea hau.
Ka nako e sa lekanyetsoang, Sensor ea Tilt e se e ntse e lokela ho hokahanngoa le Garage Door Controller ea hau, haeba u fumana hore ha li kopane hammoho 'me boemo ba sensor bo sekametseng ha bo fetole boemo ba Garage Door Controller ea hau holima sebopeho sa hau, ka kopo latela mehato e ka tlase.
- Tobetsa o tšoare konopo ea mantlha ea GDC (e ka pele ho yuniti) metsotsoana e 5 ebe o lokolla.
- Etsa bonnete ba hore e kentse mochini oa ho kopanya lipalara, sheba ka morao ho GDC ebe u bua ka LED, e lokela ho panya butle butle ka sekhahla sa motsotsoana.
- Tlanya ho Shebella Sensor tampsw switch once.
- LED ea yuniti ea mantlha ea GDC e lokela ho emisa ho panya e lokelang ho supa hore ba babeli ba atlehile.
Mehato ea Calibration ka Parameter 34.
Haeba u netefalitse hore ho hlongoa ho atlehile, o hloka ho lekanya Sensor hang. Bakeng sa mehato e qaqileng ea ho lekanya, ka kopo sheba ho "Parameter 34 ea phetolo" ka tlase: Parameter 34 [1 byte dec] e ka hlophisoa ka tsela ea heke kapa molaoli oa hau.
1. Lumella monyako oa karache ho ea sebakeng se haufi ka ho romella litaelo tsa taolo kapa ho tobetsa switch switch.
2. Romella paramethara ena (34) e nang le “value = 1” ho Garage Door Controller ka heke / molaoli oa hau.
3. Lumella monyako oa karache ho ea boemong bo bulehileng ka ho romella litaelo tsa taolo kapa ho tobetsa switch switch.
4. Lumella monyako oa karache ho ea sebakeng se haufi ka ho fetisa ka ho romella litaelo tsa taolo kapa ho tobetsa ka letsoho ka mor'a hore mohato oa 3 o qete.
Ho lekanya molaoli oa monyako oa Garage ka letsoho.
U ka lekanya Garage Door Controller ka letsoho u sebelisa mehato ena, ha ua tlameha ho sebelisa li-setting tsa tlhophiso ho beha lemati la karache, 'me e kanna ea ba tse ratehang le ho ba bonolo ho li etsa ka letsoho.
- Netefatsa hore lemati la karache le koetsoe, 'me senotlolo sa ho sekama se maemong a koetsoeng, ha GDC e bonts'a boemo bo KWETSITSOENG bohokelong ba heke ea hau.
- U sebelisa konopo e kholo e ka pele ho yuniti (switch Button), tobetsa 'me u tšoare konopo ea eona fatše metsotsoana e 10, ebe u e tlohella. Haeba e atlehile, marang-rang a LED ka morao a tla panya ka lebelo ho bontša hore e maemong a calibration.
- Bula monyako oa karache u sebelisa Button ea GDC, kapa ka litaelo tsa Z-Wave. E ke e bulehe hohle.
- Joale koala lemati la karache u sebelisa Button ea switch ho GDC, kapa ka litaelo tsa Z-Wave. E ke e koale tsela eohle.
- Litlhaku li se li felile.
Litaelo tse tsoetseng pele.
BOHLOKOA TŠIRELETSO LITAELO.
TEMOSO - HO Fokotsa Likotsi Tsa Kotsi Kapa Lefu:
1. BALA 'Me U LATELLE LITAELO TSOHLE.
2. Le ka mohla u se lumelle bana ho sebetsa kapa ho bapala ka mamati a mamati. TSOELA TAOLE Hōle le bana.
3. KAMEHLA KAMOO U TSAMAEA MONYAKO O TSOANG PELE LE BATHO LE LITLHAKISO HO FIHLELA HO KOOA KA HO FELE. HA HO MOTHO EA LOKELANG HO TSELA TSELENG EA MONYAKO O TSAMAEA.
4. BOLOKA DITAELO TSE.
Ho tlosa molaoli oa monyako oa Garage marang-rang a Z-Wave.
Litaelo tse latelang li tla u joetsa mokhoa oa ho tlosa Garage Door Controller ea hau marang-rang a hau a Z-Wave.
Haeba u sebelisa heke e teng (ke hore. Vera, Smartthings, ISY994i ZW, Fibaro, jj):
U kanna ua hloka ho sheba mokhoa oa heke ea hau ea ho khetholla kapa ho sa sebetse lisebelisoa haeba u sa tsebe ho hlakola sesebelisoa sa Z-Wave.
1. Kenya tsela ea hau ea mantlha ea Z-Wave molemong oa ho se hlophise kapa ho khetholla, tsela ea hau ea Z-Wave e lokela ho netefatsa hore e emetse ho kenya sesebelisoa se secha
2. Tobetsa konopo ea Z-Wave ho Molaoli oa Monyako oa Garage. LED ho Garage Door Controller e tla panya ka potlako, e lateloe ke LED e tiileng bakeng sa motsotsoana o le mong le motso o mong bakeng sa ho qheleloa ka thoko.
3. Marang-rang a marang-rang a Taolo ea Monyako oa Garage joale a se a ntse a panya butle ho bontša hore e se e loketse ho hokahanngoa le marang-rang a macha.
Haeba u sebelisa Z-Stick:
1. Haeba Z-Stick ya hao e hoketswe keiting kapa khomphuteng, e lokolle.
2. Nka Z-Stick ea hao ho Garage Door Controller ea hau.
3. Tobetsa konopo ea khato ho Z-Stick ea hau.
4. Tobetsa konopo ea Z-Wave ho Garage Door Controller ea hau.
5. Haeba Garage Door Controller ea hau e tlositsoe ka katleho marang-rang a hau, marang-rang a eona a LED a tla panya. Haeba ho tlosoa ho sa atleha, Network LED ha e na ho panya.
6. Tobetsa Konopo ea Ts'ebetso ho Z-Stick ho e ntša mokhoeng oa ho tlosa.
Haeba u sebelisa Minimote:
1. Nka Minimote ea hau ho Garage Door Controller ea hau.
2. Tobetsa konopo ea Tlosa ho Minimote ea hau.
3. Tobetsa konopo ea Z-Wave ho Garage Door Controller ea hau.
4. Haeba Garage Door Controller ea hau e tlositsoe ka katleho marang-rang a hau, marang-rang a eona a LED a tla panya. Haeba ho tlosoa ho sa atleha, Network LED ha e na ho panya.
5. Tobetsa konopo efe kapa efe ho Minimote ea hau ho e ntša mokhoeng oa ho tlosa.
Khutlisa molaoli oa monyako oa Garage.
Haeba molaoli oa hau ea mantlha a le sieo kapa a sa sebetse, o kanna oa lakatsa ho seta Garage Door Controller ea hau ho li-setting tsa eona tsa feme. Ho etsa sena:
- Tobetsa o tšoare konopo ea Z-Wave metsotsoana e 20 ebe oa e lokolla.
Motsamaisi oa hau oa Garage Door o se a tla hlophisetsoa bocha maemong a eona a mantlha, 'me Network LED e tla tiea metsotsoana e 2 ebe o qala ho panya butle ho netefatsa katleho.
Khoasolla melumo e mecha ho Garage Door Controller ea hau ho tsoa ho PC.
1. Sebelisa thapo ea Micro USB ho hokela Garage Door Controller ho PC ea hau. Moamoheli oa PC o tla bona polokelo e tlosoang kamora metsotsoana e seng mekae ebe o tla e fumana karolong ea "Sesebelisoa se nang le polokelo e tlosoang".
2. Tobetsa habeli ho "Removable Disk (G :)" ho e bula.
3. Joale o ka kopitsa / hula melumo e mecha ea alamo ho tsoa ho hard disk ea PC ho ea memori ea Molaoli oa Garage Door.
4. Ema metsotso e seng mekae ho qeta ho kopitsa.
Hlokomela: Ka kopo o seke oa hakolla boema-kepe ba USB ho fihlela ho kopitsa ho phethetsoe.
Lokisa molumo oa alamo ea Garage Door Controller.
O ka hlophisa molaoli oa hau oa Garage Door hore o be le melumo e fapaneng bakeng sa alamo ea ho bula, Alamo ea ho koala, Alamo e sa Tsejoeng ea Open, le Alamo ea ho koala e sa tsejoeng. Ho etsa joalo, sheba sehokela sena:
Thibela alamo ea hau ea Taolo ea Monyako oa Garage.
U ka tima ka botlalo li-alamo tsa hau tsa Garage Door Controller haeba u sa batle ho ba le melumo kapa mabone a otlang. Ho u etsa, ka kopo latela sehokelo sa thjs mona:
Liphetoho tse ling.
U kanna ua batla ho laola ka botlalo li-setting tsa Taolo ea Garage ea hau, u tla khona ho li fumana sehokelong se ka tlase bakeng sa lihlopha tsohle tsa litaelo tse tšehelitsoeng, le maemo a tlhophiso a parameter.
