JET 13R Drill Press Operator's and Parts Manual

Увод

This manual provides essential information for the safe and efficient operation, maintenance, and parts identification of the JET 13R Drill Press. It includes detailed instructions for initial setup, operational procedures, and an exploded view diagram for component identification. Adhering to the guidelines within this manual will ensure optimal performance and longevity of your drill press.

The image displays the front cover of the JET 13R Drill Press Operator's and Parts Manual. The cover features the title 'JET-13R Drill Press Operators Manual and Parts List' and an illustration of the JET 13R drill press. The bottom left corner shows 'JET Equipment & Tools' logo.

Сетуп

Proper setup is crucial for the safe and accurate operation of your JET 13R Drill Press. Follow these general steps for initial assembly and placement:

1. Распакивање: Пажљиво извадите све компоненте из паковања. Проверите да ли су сви делови наведени у листи паковања присутни и да ли су неоштећени.
2. Склоп базе: Securely attach the column to the base using the provided fasteners. Ensure the base is placed on a stable, level surface capable of supporting the drill press's weight.
3. Главна скупштина: Mount the drill press head onto the column. Tighten all securing bolts firmly.
4. Склоп стола: Install the work table onto the column. Adjust its height and angle as needed, ensuring it can be locked securely in position.
5. Уградња стезне главе: Clean the tapered spindle and chuck bore thoroughly. Install the chuck onto the spindle by firmly pressing it into place. Refer to the 'Chuck Removal' section for detailed instructions on proper installation.
6. Прикључак за напајање: Connect the drill press to a grounded power outlet of the correct voltage as specified on the motor label.

Упутство за употребу

Before operating the JET 13R Drill Press, ensure you have read and understood all safety warnings. Always wear appropriate personal protective equipment, including eye protection.

1. Припрема материјала: Сигурно цлamp the workpiece to the drill press table. Never hold the workpiece by hand during drilling operations.
2. Инсталација бита: Insert the drill bit into the chuck, ensuring it is centered and tightened securely with the chuck key. Remove the chuck key before starting the machine.
3. Подешавање брзине: Adjust the pulley and motor speeds according to the material being drilled and the drill bit size. Refer to the speed chart (if available on the machine or in the full manual) for recommended settings. To change speeds, open the belt cover, loosen the motor lock, and adjust the belt position on the pulleys. Re-tension the belt and close the cover before operation.
4. Стопа дубине: Set the depth stop to control the drilling depth.
5. Операција: Turn on the drill press. Allow the motor to reach full speed before engaging the drill bit with the workpiece. Apply steady, even pressure to the feed handle.
6. Хлађење: Use appropriate cutting fluid for certain materials to reduce heat and extend bit life.
7. Завршетак: Once drilling is complete, retract the drill bit from the workpiece, turn off the machine, and wait for the spindle to stop completely before removing the workpiece.

Одржавање

Regular maintenance ensures the longevity and safe operation of your JET 13R Drill Press.

• Чишћење: Keep the drill press clean and free of chips and dust. Use a brush or vacuum; never use compressed air directly on the machine as it can force debris into moving parts.
• подмазивање: Periodically lubricate moving parts as specified in the full manual.
• Chuck Removal and Maintenance: To remove the chuck, lower the spindle to its lowest position. Insert a chuck wedge into the slot between the chuck and the spindle collar, then tap lightly with a mallet to dislodge the chuck. Clean the tapered surfaces before reinstallation.
• Преглед појасева: Regularly inspect the drive belts for wear, cracks, or damage. Replace worn belts promptly. Ensure proper belt tension.
• Провера причвршћивача: Периодично проверавајте затегнутост свих навртки, вијка и завртња. Затегните све лабаве причвршћиваче.

Решавање проблема

This section addresses common issues that may arise during the operation of your JET 13R Drill Press.

• Motor Does Not Start:
  • Проверите прикључак за напајање и прекидач.
  • Уверите се да је прекидач за напајање у положају „УКЉУЧЕНО“.
  • Verify that the belt cover is closed, as some models have a safety interlock.
• Претерана вибрација или бука:
  • Check for loose fasteners on the base, column, or head.
  • Inspect drive belts for wear or improper tension.
  • Ensure the chuck and drill bit are properly installed and tightened.
• Drill Bit Wobbles:
  • Re-seat the drill bit in the chuck, ensuring it is fully inserted and tightened.
  • Inspect the drill bit for damage or bending.
  • Check the chuck for damage or runout.
• Inaccurate Drilling:
  • Уверите се да је радни предмет безбедно цлampед за сто.
  • Verify the drill press table is square to the spindle.
  • Check for excessive play in the spindle or quill.

For issues not covered here, consult a qualified service technician.

Спецификације

The JET 13R Drill Press is designed for precision drilling tasks. While specific technical specifications may vary slightly by manufacturing year, common features and operational parameters include:

• Капацитет бушења: Typically around 1/2 inch in steel, larger in softer materials.
• Путовање вретеном: Standard travel for accurate depth control.
• Мотор: Induction motor, typically 1/2 HP or similar, designed for continuous operation.
• Брзине: Multiple speed settings, often 4 or 5, adjustable via belt and pulley system to accommodate various materials and bit sizes.
• Табела: Cast iron work table, adjustable for height and angle, with slots for clampобрађивање радних предмета.
• Цхуцк: Keyed chuck for secure bit retention.

Листа делова и експлозија View Дијаграми

This manual includes detailed exploded view diagrams of the JET 13R Drill Press, accompanied by descriptions of individual parts. These diagrams are invaluable for identifying components during assembly, disassembly, or when ordering replacement parts. Each part is typically numbered on the diagram, corresponding to a list that provides its name and function.

Refer to these diagrams for:

• Identifying specific components of the drill press.
• Understanding the assembly order of various sections (e.g., head, column, base, table).
• Locating parts for maintenance or repair procedures.

Note: Specific part numbers may not be included in this reproduction manual. For precise part numbers, please consult an official JET Tools parts catalog or authorized dealer.