Увод
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Hager 30S-4x16 Beveled Square Corner Push Plate. Designed for durability and functionality, this push plate protects doors from wear and tear in high-traffic areas. Please read these instructions carefully before installation to ensure proper function and longevity of the product.
Подешавање и инсталација
Потребни алати:
- Оловка или маркер
- Мерна трака
- Drill with appropriate drill bit (for pilot holes)
- Screwdriver (manual or power)
- Level (optional, for precise alignment)
Кораци инсталације:
- Prepare the Door Surface: Ensure the door surface where the push plate will be installed is clean, dry, and free from debris.
- Position the Push Plate: Carefully place the Hager 30S-4x16 push plate on the desired location on the door. Use a measuring tape to ensure it is centered or aligned as required. A level can be used to verify horizontal and vertical alignment.
- Mark Screw Hole Locations: Using a pencil or marker, carefully mark the center of each of the six pre-drilled holes on the door surface.
- Избушите пилот рупе: Remove the push plate. Using a drill with a drill bit slightly smaller than the screw diameter, drill pilot holes at each marked location. Drill only deep enough to accommodate the screw length.
- Attach the Push Plate: Reposition the push plate, aligning its holes with the newly drilled pilot holes. Insert the provided screws into each hole and tighten them securely with a screwdriver. Do not overtighten, as this may strip the screw threads or damage the door surface.
- Коначна провера: Verify that the push plate is firmly attached and does not wobble.
This image displays the Hager 30S-4x16 Beveled Square Corner Push Plate. It is a rectangular, flat metal plate with a light, possibly brushed, finish. There are six pre-drilled holes for mounting screws: two at the top, two in the middle, and two at the bottom, symmetrically placed along the vertical edges. The corners appear to be square with a slight bevel.
Операција
The Hager 30S-4x16 Beveled Square Corner Push Plate is a passive door accessory designed to protect the door surface from damage caused by repeated pushing. No specific operational steps are required beyond its proper installation. Users should push the door by applying pressure to the push plate area.
Одржавање
To maintain the appearance and integrity of your push plate, follow these simple guidelines:
- Редовно чишћење: Clean the push plate periodically with a soft, damp cloth and mild soap. Avoid abrasive cleaners, harsh chemicals, or scouring pads, as these can scratch the finish.
- Сушење: After cleaning, wipe the surface dry with a clean, soft cloth to prevent water spots.
- Прегледајте причвршћиваче: Periodically check the mounting screws to ensure they remain tight. Retighten if necessary to prevent the plate from becoming loose.
Решавање проблема
| Иссуе | Могући узрок | Решење |
|---|---|---|
| Потисна плоча је лабава или се клима. | Вијци за монтажу су олабављени. | Чврсто затегните све монтажне завртње. Немојте превише затезати. |
| Scratches or marks on the plate. | Normal wear and tear; abrasive cleaning. | Minor scratches may be polished with appropriate metal polish (test in an inconspicuous area first). Avoid abrasive cleaners for future maintenance. |
| Plate does not sit flush. | Uneven door surface; improper installation. | Ensure the door surface is flat. Re-install, ensuring screws are tightened evenly. |
Спецификације
- Модел: Hager 30S-4x16
- Димензије: 4 инча (ширина) к 16 инча (висина)
- дебљина: 0.050 инча
- Материјал: (Note: Specific material not provided in product data. Typically durable metal alloy.)
- Corner Type: Beveled Square Corner
- Монтажа: Pre-drilled holes for screw-in installation
Гаранција и подршка
Hager products are manufactured to high-quality standards. For specific warranty information regarding your 30S-4x16 Beveled Square Corner Push Plate, please refer to the documentation included with your purchase or visit the official Hager website. For technical support or further assistance, please contact Hager customer service directly.
