Specification: UHF RFID Reader
Model Name : ASR-X3XD
Project Name : UHF RFID Reader
Revision : Rev.0
Supplier Approval
|
Made by |
Checked by | Approved by |
|
YB Kim |
||
|
2022-08-19 |
Customer Approval
|
Checked by |
Checked by |
Approved by |
Smart Power Solutions, Inc.
|
Products |
Dongle RFID | Reversion | Rev.0 |
| Document No | SQP-0621-xx | Released |
2022-08-19 |
|
Created By |
Youngbeom Kim |
Revised By |
|
|
Page |
2/6 page |
Revision Date |
Revision Descriptions
|
Rev |
ECN | Description | Approved by | Date |
| A101 | Initial draft |
2022.08.19 |
1. Scope
1.1. Introduction
Mobile UHF RFID reader allow you to read RFID tags and transmit the data to any Bluetooth Low Energy(BLE) enabled device. It complies RFID standard (Air Protocol: EPC Gen2 V2 / ISO 180006C). It uses Li-ion battery (700mAh) as internal power. Also, it can charge RFID’s battery by using Magconn cable.
1.2. Product Views
|
Case Materials |
PC (Poly Carbonate) |
| Charging |
Magconn |
|
Trigger TAGGING button |
2 EA |
< ASR-030D >
2. Mechanical Specifications
5.1. Dimensions (mm)
5.1.1. Width x Vertical x Height (64 x 119.6 x 9.7mm)
5.2. Lead-free/RoHS
Materials and process compliant with 2002/95/EC RoHS Directive
5.3. Weight
Less than 68g
Certification and Safety Approvals FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antennae
-Increase the separation between the equipment and the receiver
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. The antenna used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures.
FCC Caution
Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment.
Industry Canada(IC) Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Contains transmitter module IC: MBN52832 (FCC ID: HSW2832 / IC: 4492A-2832)
SQP-0621(Rev.0) Smart Power Solutions
Documents / Resources
 |
SPS ASR-X3XD UHF RFID Reader [pdf] Owner's Manual 2AJXE-ASR-X3XX, 2AJXEASRX3XX, ASR-X3XD UHF RFID Reader, ASR-X3XD, ASR-X3XD RFID Reader, UHF RFID Reader, RFID Reader, UHF Reader, Reader |
