User Manual V1.0
SpeedyBee F7 35A BLS Mini Stack
Pat 1 -Overview
Specs Overview
| Product Name | SpeedyBee F7 35A BLS Mini Stack |
| Flight Controller | SpeedyBee F7 Mini |
| ESC | SpeedyBee 35A BLS Mini 4-in-1 ESC |
| Bluetooth | Supported. For FC & ESC parameter setting |
| Wireless FC Firmware Flashing | Not supported |
| Wireless Blackbox Download | Not supported |
| Power Input | 3-6S LiPo |
| Mounting | 20 x 20mm Ø3.5mm hole size, Compatible with M2 and M3 screws/Silicone grommets |
| Dimension | 32mm(L) x 35mm(W) x 13mm(H) |
| Weight | 12.7g |
Dimensions
Package
- SpeedyBee F7 Mini Flight Controller x 1
- SpeedyBee 35A BLHeli_S Mini 4-in-1 ESC x 1
- Manual & App Download Card x 1
- XT30 Power Cable(Length: 7cm) x 1
- 8pin JST cable(For FC & ESC Connection） x 1
- 35V 470uF Capacitor x 1
- M2 Accessories
- M2(Diameter) * 20mm(Length) Screw x 4
- M2(Diameter) * 25mm(Length) Screw x 4
- M2(Hole Diameter) * 6.6mm(Height) Anti-vibration Silicone Grommets x 9
- M2 Silicone O-Ring x 5
- M2 Nylon Hex Nut x 5
- M3 Accessories
- M3(Diameter) * 20mm(Length) Screw x 4
- M3(Diameter) * 25mm(Length) Screw x 4
- M3(Hole Diameter) * 6.6mm(Height) Anti-vibration Silicone Grommets x 9
- M3 Silicone O-Ring x 5
- M3 Nylon Hex Nut x 5
FC & ESC Connection
Use any end of the 8-pin JST cable to connect the FC to the ESC.
Part 2 – SpeedyBee F7 Mini Flight Controller
Layout
LED Indicator Definition
RED LED – Solid Red after powering up.
GREEN LED – Blinking Green indicates Bluetooth is open and waiting for connection; Solid Green indicates Bluetooth is connected.
BLUE LED – Flight controller status light which is controlled by the flight controller firmware.
BOOT Button
Only if the flight controller gets bricked and can’t power up, please follow these steps to re-flash firmware for it:
① Insert a USB A to TYPE-C cable to your PC.
② Press and hold the BOOT button, insert the USB cable into the flight controller, then release the BOOT button.
③ Open Betaflight/Emuflight/INAV configurator on the PC, go to the ‘Firmware Flashing’ page, choose the target ‘SPEEDYBEEF7MINI’ and flash.
FC’s Peripheral Connection
APP
- Get the SpeedyBee App
Search ‘SpeedyBee’ on Google Play or App Store. Or download the Android .apk file on our website: https://www.speedybee.com/download. - Connect the App
FC Firmware Update
SpeedyBee F7 Mini does not support wireless firmware flashing, so please flash firmware for it on your PC by following the steps below:
① Connect the flight controller to the PC with a USB cable
② Open Betafight/Emuflight/INAV configurator on your PC. Take the Betaflight configurator as an example, go to the ‘Firmware Flashing’ page, choose the target ‘SPEEDYBEEF7MINI’, and flash.
Parameters
| MCU | STM32F722 |
| IMU(Gyro) | BMI270 for current batches;MPU5000 for old batches before May 2022. |
| USB Port Type | Type-C |
| Barometer | N/A |
| OSD Chip | AT7456E chip |
| BLE Bluetooth | Supported. Used for Flight Controller configuration (MSP should he enabled with Baud rate 115200 on UART 6) |
| Flash FC Firmware Wirelessly | Not supported. Please update the firmware for this FC on the PC |
| Download/Analyze Blackbox | Not supported. Please download and analyze Blackbox data on the PC |
| DJI Air Unit Soldering Pads | Supported |
| Flash(for BlackBox) | 8MB |
| Current Sensor | Supported, Scale=250 Offset=-500 |
| BetaFlight Camera Control Pad | Yes(CC pad) |
| Power Input | 35 – 65 Lipo |
| 5V Output | 6 groups of 5V output, five +5V pads and 1 BZ+ pad( used for Buzzer). The total current load is 2.5A. |
| 9V Output | 2 groups of 9V output, the total current load is 2A. |
| 3.3V Output | Supported. Up to 500mA current load. |
| ESC Signal Pads | M1 – M4 |
| UART | Full UART * 3(UART1, UART2, UART3) |
| ESC Telemetry UART | R4(UART4) |
| I2C | Not supported |
| LED Pad | Used for W52812 LED |
| Buzzer | BZ+ and BZ- pad used for 5V Buzzer |
| BOOT Button | Used to enter DFU mode |
| RSSI Input | Not supported |
| SmartPort | Use any D< pad of UART for the SmartPort feature. |
| Supported Flight Controller Firmware | BetaFlight(Default), EMUFlight, INAV |
| Firmware Target Name | SPEEDYBEEF7MINIV2 for current batches(Gyro: BMI270); SPEEDYBEEF7MINI for old batches(Gyro: MPU6000) before May 2022. |
| Mounting | 20x 20mm, 3.5mm hole diameter |
| Dimension | 30x 30 x 7.5mm |
| Weight | 5.7g |
Part 3 – SpeedyBee 35A BLS 4-in-1 ESC
Layout
Connection with Motors & Power Cable
Note: In order to prevent the stack from being burnt out instantaneous voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor in the package.
ESC Configuration
ESC Firmware Update
You could flash both BLHeli_S and Blue Jay firmware for this ESC via
Bluetooth.Note: ESC Type should be set as ‘J-H-40’.
Parameters
| Firmware | BLHeli_S JH40 |
| Continuous Current | 35A * 4 |
| Burst Current | 45A(55) |
| ESC Protocol | DSHOT300/600 |
| Power Input | 3-65 LiPo |
| Power Output | VBAT |
| Current Sensor | Support (Scale=250 Offset=-500) |
| Mounting | 20 x 20mm, 3.6mm hole diameter |
| Dimension | 32(L) * 35(W) * 5.5mm(H) |
| Weight | 7g |
Documents / Resources
 |
SpeedyBee F7 35A BLS Mini Stack Flight Controller [pdf] User Manual F7 35A BLS Mini Stack Flight Controller, F7, 35A BLS Mini Stack Flight Controller, Mini Stack Flight Controller, Flight Controller, Controller |
