EMPAKKT0 mpower Arrow Kit
“
Specifications:
- Input Voltage Range: 10-32Vdc
- Operating Temperature: Standard
- Electrical Protection: Reverse Polarity, Transient Voltage
Over-Voltage, High-Temperature Thermal Fold-back - Material: Brackets – Powder coated steel, LED Modules – Dow
Corning Silicone Lens - Wiring: Power Cable – 15ft, 16AWG Wires, (+) RED, (-) BLACK,
Data Line – 20AWG GREEN - Standby Current (Per Module): IGNITION ON – 0.20 Amps, IGNITION
OFF – (Not specified)
Product Usage Instructions:
Installation:
- Ensure that the SoundOff Central Lightbar is installed in the
lower left-hand corner of the approved vehicle. - Connect the 15′ Y-Harness with weatherproof connectors to the
mpower Arrow Kit based on configured specifications. - Optionally, connect the Breakout Box according to your
vehicle’s LIN or CAN system.
Power Supply:
Make sure to connect the Power Cable properly with the red wire
to the positive terminal and the black wire to the negative
terminal. Ensure proper wiring to avoid electrical issues.
Maintenance:
Regularly inspect the brackets and LED modules for any damage.
Clean the lenses with a soft cloth to maintain visibility.
FAQ:
Q: Can I use this product on any vehicle?
A: No, this product is designed to be used ONLY on approved
vehicles. It is essential to ensure compliance with vehicle
regulations.
Q: What should I do if there is an airbag deployment zone in
the installation area?
A: Avoid installing the SoundOff Central Lightbar in areas with
airbag deployment zones to prevent interference with safety
systems.
“`
INSTALLATION INSTRUCTIONS mpower® ARROW KIT
EMPAKKT0(X)*
EMPAKXXXXX
*mpower modules sold separately
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
IMPORTANT NOTICE TO INSTALLER: · Make sure to read and understand all instructions and warnings before proceeding with the installation of this product.
Ensure that the manual and any warning cards are delivered to the end user of this equipment. Proper installation of the Arrow Kit requires the installer to have a thorough knowledge of automotive electronics, systems, and procedures. · Arrow Kits provide an essential function of an effective visual warning system. The use of the Arrow Kit does not insure that all drivers can or will abide by or react to an emergency warning signal, especially at high rates of speeds or long distances. The operator of the vehicle must never take the right of way for granted and it is the operator’s responsibility to proceed safely. · The effectiveness of the Arrow Kit is highly dependent on the correct mounting and wiring. The installer must read and follow the manufacturer’s installation instructions and warnings in the manual. The vehicle operator should verify daily that the Arrow Kit is securely fastened to the vehicle and properly functioning before operating vehicle. · The Arrow Kit is intended for use by authorized personnel only. It is the user’s responsibility to ensure they understand and operate the emergency warning devices in compliance with the applicable city, state and federal laws and regulations. SoundOff Signal assumes no liability for any loss resulting from the use of this warning device.
! WARNING
· This product contains high intensity LED devices to prevent eye damage, DO NOT stare into the light beam at close range.
IMPORTANT INFORMATION:
· To view the full Software Revision History click the
in the lower left hand corner of the SoundOff Central Lightbar
application.
· Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be
used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.
· DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to your vehicle Owner’s Manual for
the location of any air bag deployment zones.
· DO NOT connect this device to a strobe power supply. This product is self-contained and does not require an external
power supply.
! WARNING
· Route wires only in locations that are not subject to potential wear. Make sure to avoid routing wires in the deployment area of your airbag. Refer to your vehicle’s owner’s manual for airbag deployment zone.
· All customer supplied power wires connecting to the positive (+) or negative (-) battery terminal or local chassis ground (-) must be sized to supply at least 125% of the maximum current and properly fused at the power source with appropriately rated fuse.
NOTICE: · Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning
devices. · Improper use or installation may void warranty coverage. · To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at
www.soundoffsignal.com/tech-services/returns/. · If you have questions regarding this product, contact Technical Services, Monday – Friday, 8 a.m. to 5 p.m. ET at
1.800.338.7337 (press #4). · Questions or comments that do not require immediate attention may be emailed to techgroup@soundoffsignal.com.
2
800-338-7337 | soundoffsignal.com
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
Table of Contents
Components/Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Module, Technical & Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Light Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Light Mounting Templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 – 7 Electrical Installation / Control Harness / Break out Box (BOB) . . . . . . . . . . . . . . . 8 – 11 Function Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Electrical Installation Flash Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 – 17 Default Siren Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Connection of Breakout Box to SoundOff Signal Sirens . . . . . . . . . . . . . . . . . . . . . . 18 mpower Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Replacement Parts & Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Warranty & Return Goods Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3
800-338-7337 | soundoffsignal.com
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
CONTENTS
QTY
COMPONENT
1
mpower Arrow Kit built to configured specifications*
1
15′ Y-Harness with weatherproof connectors
*Will vary based on configured product.
OPTIONAL CONTROL EQUIPMENT
COMPONENTS
Breakout Box Breakout Box
LIN (Standard) CAN System
Qty.
Qty.
Universal BOB (LIN)
1
0
Universal BOB (CAN)
0
1
24 Pin Harness
1
1
4 Pin Harness
1
1
5 Pin Harness
0
1
INPUT VOLTAGE RANGE OPERATING TEMPERATURE
ELECTRICAL PROTECTION
TECHNICAL SPECIFICATIONS
10-32Vdc
-40°C to +65°C (-40°F to +149°F)
Reverse Polarity, Transient Voltage Over-Voltage, High-Temperature Thermal Fold-back
MATERIAL
Brackets: Powder coated steel LED Modules: Dow Corning Silicone Lens
WIRING
Power Cable: 15ft, 16AWG Wires, (+) RED, (-) BLACK Data Line: 20AWG GREEN
STANDBY CURRENT(Per Module)
IGNITION ON: 0.20 Amps IGNITION OFF: <8.5 mA
STANDBY POWER(Per Module)
IGNITION ON: 2.560 Watts IGNITION OFF: 0.108 Watts
3″: 4 LED Single Color, 8 LED Single Color, 8 LED Dual Color, 12 LED Tri Color
INPUT VOLTAGE RANGE: 10-32Vdc CURRENT DRAW: 0.26A mps @ 12.8 Vdc (Flashing Red)
0.62 Amps @ 12.8 Vdc (Peak Red) 0.38Amps @ 12.8 Vdc (Flashing Amber, Blue, Green, White) 0.90 Amps @ 12.8 Vdc (Peak Amber, Blue, Green, White) WATTAGE: 3.3W @ 12.8 Vdc (Flashing Red) 4.9W @ 12.8 Vdc (Flashing Amber, Blue, Green, White)
4″: 6 & 8 LED Single Color, 12 LED Dual & 18 LED Tri Color Module INPUT VOLTAGE RANGE: 10-32Vdc CURRENT DRAW: 0.36 Amps @ 12.8 Vdc (Flashing Red)
0.62 Amps @ 12.8 Vdc (Peak Red) 0.60 Amps @ 12.8 Vdc (Flashing Amber, Blue, Green, White) 0.90 Amps @ 12.8 Vdc (Peak Amber, Blue, Green, White)
WATTAGE: 4.6W (Red) 7.7W (Amber, Blue, Green, White)
CERTIFICATION SAEJ595
CALIFORNIA TITLE 13 NFPA 1901-2009
KKK-A-1822F (JULY 2021)
APPLICABLE COLORS
Red, Amber, Blue, White, Green
Red, Amber, Blue
Red, Amber, Blue, White
Red, Amber, Blue, White, Green
Tools Required for Installation · 7/16″ Socket with ratchet · Phillips Head Screwdriver · Drill bit #30 ·5/32 Hex Drive or Allen Wrench
FLASHING = AVERAGE STEADY ON (100%) = PEAK
Unpack Arrow Kit 1. Remove Arrow Kit from box and packaging. 2. Save packaging for later shipping. 3. Check components/contents. 4. Please reference these instructions for proper wiring and installation.
4
800-338-7337 | soundoffsignal.com
FLASHING = AVERAGE STEADY ON (100%) = PEAK
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
MPOWER 3-WIRE LIGHTS – 3″ & 4″ INSTALLATION:
Stud Mount (Figure 1) 1. Pre-Drill per stud mount pattern indicated on
page 4, 5 per the supplied mounting template. 2. Clean the surface as required. 3. Deburr hole as required. 4. Feed wire through the drilled wire hole and make
mating plug connection. 5. Install light, inserting 2 studs into the 2 drilled holes. 6. Install 2 lock nuts onto studs behind mount surface.
Hand tighten only until mount surface and light are flush.
Screw Mount (Figure 3) 1. Pre-Drill per screw mount pattern indicated on
page 4, 5. 2. Deburr and clean the surface as required. 3. Feed wire through the drilled wire hole and make
mating plug connection. 4. Install light with 2x Torx drive screws and hand
tighten only until mount surface and light are flush.
FIG. 2
Quick Mount (Figure 2) 1. Pre-Drill per quick mount pattern indicated on
page 4, 5 (wire hole only.) 2. Deburr hole as required. 3. Clean surface with supplied alcohol wipe. 4. Feed wire through the drilled wire hole and make
mating plug connection. 5. Remove adhesive backer and align light into desired
position. Apply to surface and hold firmly for 30
seconds. CAUTION! APPLY UNIFORM PRESSURE
ACROSS FULL FACE OF LIGHT.
QUICK MOUNT
ADHESIVE SURFACE
FIG. 1
FIG. 3
WIRE HOLE LOCKNUT x2
THREADED STUD x2 MOUNT SURFACE
STUD MOUNT – THREADED (SHOWN)
SCREW MOUNT
TORX DRIVE SCREWS x2
5
800-338-7337 | soundoffsignal.com
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
MPOWER 3-WIRE LIGHTS 3″ TEMPLATE
3″ QUICK MOUNT
WIRE THRU-HOLE
7/16″ DRILL 11.00
3″ STUD MOUNT
0.875±0.01 22.23±0.25
0.875±0.01 22.23±0.25
6
2X DRILL INSERT HOLES
0.16±0.01 4±0
WIRE THRU-HOLE
7/16″
3″ SCREW MOUNT
1.56±0.01 39.50±0.25
1.56±0.01 39.50±0.25
2X DRILL INSERT HOLES
0.04±0.01 1.00±0.15
WIRE THRU-HOLE
7/16″ DRILL 11.00
IMPORTANT NOTE:
Due to variations in the printing process and environmental factors, the sizes shown may not be accurate. If this document is used as a cutting template, it is the installers responsibility to confirm the accuracy of the dimensions shown and adjust accordingly.
800-338-7337 | soundoffsignal.com
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
MPOWER 3-WIRE LIGHTS 4″ TEMPLATE
4″ QUICK MOUNT
WIRE THRU-HOLE
7/16″ DRILL 11.00
4″ STUD MOUNT
0.98±0.01 25±0
0.98±0.01 25±0
7
2X DRILL INSERT HOLES
0.16±0.01 4±0
WIRE THRU-HOLE
7/16 DRILL 11.00
4″ SCREW MOUNT
2.15±0.01 54.50±0.25
2.15±0.01 54.50±0.25
2X DRILL INSERT HOLES
0.04±0.01 1.00±0.15
WIRE THRU-HOLE
7/16 DRILL 11.00
IMPORTANT NOTE:
Due to variations in the printing process and environmental factors, the sizes shown may not be accurate. If this document is used as a cutting template, it is the installers responsibility to confirm the accuracy of the dimensions shown and adjust accordingly.
800-338-7337 | soundoffsignal.com
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
ELECTRICAL INSTALLATION
Arrow Kit 1. Find a good location to drill a hole to pass the 15″ Y-harness into the vehicle. If the vehicle manufacturer
has specific instructions please follow them for proper installation. 2. Secure wires from the mpower® 3-Wire Lights and the Y-harness. The wires are shipped without constraints
of zip-ties or wire ties, you may tuck and fasten the wires as desired to secure them in your installation. Cut off the unused connector(s) and tape the exposed wires, or seal the unused connectors to prevent electrical shorting. 3. Connect the ends of the distribution harness to the Y-Harness, as shown on the left. The harness plugs are not specific. You may use either weatherproof connector. 4. Connect the RED, BLACK, and GREEN wires as outlined in the electrical section of the installation instructions.
! WARNING
ALL CUSTOMER SUPPLIED POWER WIRES CONNECTING TO THE POSITIVE (+) OR NEGA TIVE (-) BA TTERY TERMINAL OR LOCAL CHASIS GROUND (-) MUST BE SIZED TO SUPP LY AT LEAST 125% OF THE MAXIMUM
CURRENT AND PROPERLY FUSED AT THE POWER SOURCE WITH APPROPI ATELY RATED FUSE.
Arrow Kit Power Cable: 1. Route arrow kit power cable as close to vehicles
power source (battery) as possible. 2. Install a maximum of 10 Amp Fuse (customer
supplied) to the end of the RED wire of the Arrow Kit Power Cable. a. Remove the fuse before connecting any wires to
the POSITIVE (+) terminal of the battery. b. DO NOT USE CIRCUIT BREAKER OR FUSIBLE
LINK. c. Do NOT use any more than 2ft of wire between
the power source and the fuse and ensure the wire is protected and secured from being cut into; this is non-fused wire. 3. Connect the BLACK wire to the factory chassis ground right next to the battery or other ground location capable of handling high current.
Arrow Kit Control (Data) Cable: 1. Connect the Green wire from the Arrow Kit to the
Solid Green (PIN 3) on the 4 PIN Harness.
Breakout Box Power Wiring: 1. Connect the Pink/White wire (Pin 12 of the 24 pin
wire harness) to a switched 12-32V power source. Breakout Box needs constant power 12-32V to the Red wire (PIN 4 on 4 pin harness) & Ground to Black, PIN 1 on 4 pin harness) in order to operate. 2. Insert Fuse(s) into Fuse Holder(s). 3. Observe the GREEN Data Link indicator LED on the Breakout Box; the LED will turn ON. 4. The Red indicator LED on the breakout box will be steady ON whenever any of the input wires are active.
Low Power (Standby) Mode (reduced standby current) If there is no input to the breakout box the arrow kit will go into a “standby” mode. The standby mode is a low power mode that is used to extend the life of your battery. The Arrow Kit will awaken from the standby mode when the ignition input is activated on the breakout box.
IMPORTANT
WHEN PASSING CABLES THROUGH FIREWALL OR OTHER SHEETMETAL, INSERT GROMMET TO PROTECT THE CABLE!
8
800-338-7337 | soundoffsignal.com
! WARNING
Route wires only in locations that are not subjected to potential wear. Ma ke sure to avoid routing wires in the deployment area of your air bga. Refer to your vehicle’s
owner’s manual for airbag deployment zone.
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
ELECTRICAL INSTALLATION
* Switch #1 and #2 on the Breakout Box can be used when configuring the bar with the bluePrint Control system
7.5 Amp Fuse – 6 Mod Assembly
10 Amp Fuse – 8 Mod Assembly
Red
Black Green
Universal B.O.B. – Connectivity Side
Switch #1* Switch #2*
Red LED Green LED
–
(Ground)
+
3 Amp Fuse
(Ground)
Red Black
Universal B.O.B. – Activation Side
USB Programming Connector
Green Green/White (Not used)
(Ground)
Pink/White
ID 1
1 – 8S2 2 – 8S2
ID 2
1 – 8S2 2 – Down/On
3 Amp Fuse
+10-32 VDC Switched Ignition Source
Universal Breakout Box Setting I.D.
*Onnllyy uusseeddwwitihthbbluleuPeRPIRNITNT aapppplilcicaattiioons wiitthhmmoorreeththaann 11UUnniviveerrssaall BBrreeaalkoouut tBoBxo.x
1 – Down/On ID 3 2 – 8S2
ID 4
1 – Down/On 2 – Down/On
Functional Inputs
Functional Inputs connect to your control head or switching unit. Applying +10-32Vdc to any functional Input will activate it’s function (default-active high).
9
800-338-7337 | soundoffsignal.com
Pink/ White – PIN#12 Purple/ White – PIN#11
Gray/ White – PIN#10 Black/ White – PIN#9
White – PIN#8 Purple – PIN#7 Brown/ White – PIN#6 Light Green – PIN#5 Black – PIN#4
Gray – PIN#3 Green White – PIN#2 Blue/ White – PIN#1
PIN#24 – Light Green/ White PIN#23 – Red Black PIN#22 – Orange/ White PIN#21 – Yellow/ White PIN#20 – Brown PIN#19 – Red/ White PIN#18 – Pink PIN#17 – Red PIN#16 – Orange PIN#15 – Yellow PIN#14 – Green PIN#13 – Blue
USB Type Mini B Connector For Software Programming.
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
Wire Pin#
Wire Color
1 BLUE/WHT
2 GRN/WHT
3
GRY
4
BLK
5
LTGRN
6 BRN/WHT
7
PUR
8
WHT
9
BLK/WHT
10 GRY/WHT
11 PUR/WHT
12 PNK/WHT
13
BLU
14
GRN
15
YEL
16
ORG
17
RED
18
PNK
19 RED/WHT
20
BRN
21 YEL/WHT
22 ORG/WHT
23 RED/BLK
24 LTGRN/WHT
WIRE FUNCTION DEFAULTS
Wire Function
Cruise 1 Warning Selected at Bar Creation Selected at Bar Creation Selected at Bar Creation Unassigned Unassigned Unassigned Low Power 1 Left Arrow Right Arrow IGNITION Warning Warning Warning Warning Warning Warning with Cruise 1 behind Flashing Unassigned Unassigned Work Light Scene 1 VSS Input for Speed 1 and 2
Mods Affected
Entire Bar Entire Bar Selected at Bar Creation Selected at Bar Creation Selected at Bar Creation Unassigned Unassigned
Entire Bar Entire Bar Entire Bar
Entire Bar Entire Bar Entire Bar Entire Bar Entire Bar Entire Bar Work Light Unassigned Unassigned Selected at Bar Creation Selected at Bar Creation
–
Color ( : If the color is not populated, it would be
the next color listed)
Color 1, not White Color 1
Selected at Bar Creation Selected at Bar Creation
Red nothing –
Amber Color 1 Amber Color 1
Color 1 Color 1 Color 1 Color 1 Color 1 Color 1 White nothing White nothing White nothing White White
–
Flash
Mode 2
Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Mode 6 –
Table 1 Cert Chosen SAE / None
Pattern –
Slow Runner –
Flicker Cruise Slow Runner
Quint Intercycle
Warp Super Slow Runner
–
BREAKOUT BOX INSTRUCTIONS: (LIN COMMUNICATION)
a) Securely snap in the 4-pin and 24-pin connectors b)Connect5the Pink/White wire (Pin 12 of th4e 24 pin wire
harness) to a switched 12-32V power source. Breakout Box needs constant power 12-32V to the Red wire (PIN 4 on 4 pin E harness) & Ground to Black, PIN 1 on 4 pin harness) in order to operate. (Table 2) c) Refer to Table 1 for the input wire’s default function d) Follow the label for the wire color to connect to a +10-32Vdc source, which turns on that given light or lights e) Make sure your wire connections are secured and isolated from any other wire
4-PIN CONNECTOR HARNESS
D
Wire Pin 1 2 3 4
Color Black Green/White Green Red
Table 2 Function Ground LIN 2 – not used with this Arrow Kit LIN 1 – mpower Arrow Kit Operation Power
C
CAN BREAKOUT BOX INSTRUCTIONS: (CAN COMMUNICATION)
a) Securely snap in the 4-pin, 5-pin and 24-pin connectors b) RT3aebfeler t3ofToarbthlee1CfAoNr twheireinfpuuntctwioirnes2default functions and to c) Connect the Pink/White wire (Pin 12 of the 24 pin wire
harness) to a switched 12-32V power source.RBEVreISaIOkNouLOt GBox needs constant power 12-R3E2VV to the DREeSdCRwIPiTrIeON(PIN 4 onIN4ITIALS pin harness) & Ground to B1lack, PIN 1 on 4 pin harness) in order to operate. (Table 2) d) Follow the label for the wire color to connect to a 10-32 Vdc source, which turns on that given light or lights e) Make sure your wire connections are secured and isolated from any other wire f) If extending the 5-pin connector harness, a shielding wire
running the length of the entire harness may be necessary
CONNECTOR PRESENT WITH CAN BOB
1
ECN D
01/
Wire Pin 3 5
Color Green Yellow
Table 3 Function CAN Low CAN High
CAN CONNECTOR
10
B
CHARACTERISTIC NUMBERS
TO CHANGE WIRE FUNCTIONS FOR CUSTOM APPLICATIONS PLEASE SCANLAQSTRUSCEODDE FOR LINDKELETED
K
FOR SOUNDOFF CENTRAL LIGHTBAR SOFTWARE GUIDES.
800-338-7337 | soundoffsignal.com
NOTES: 1. CAD DATA IS MASTER 2. VOLUME = $PRPSHEET:{VOLUME MM} mm³ 3. BREAK ALL SHARP EDGES, NO BURRS ALLOWED 4. GATE & EJECTOR LOCATIONS TO BE APPROVED
BY SOUNDOFF SIGNAL PRIOR TO TOOL BUILD 5. NO SUBSTITUTION OF MATERIAL ALLOWED WITHOUT
mpower®
Arrow
Kit
no
bracketPTHREEOnIPNgRFlIOEisTRAhMRYATAIONND
CONFID CONTAI
00KPJL 042TPH5RIOSRPDEERVRATWYCOINFGSOISUTHNEDSOOFLFES
®
ANY REPRODUCTION IN PA
AS A WHOLE WITHOUT THE
TOLERANCES
WRITTEN PERMISSION OF
EXCEPT AS NOTED
SOUNDOFF SIGNAL IS PROH
.X ± .020
mpower® Arrow Kit
REAR DRIVER’S SIDE 6 MOD
LIGHT MODULE LOCATION
REAR PASSENGER’S SIDE
ID31
RINB1
8 MOD
ID32 RINB2
ID33 RINB3
ID34 RINB3
ID35 RINB2
ID36 RINB1
ID31 RINB1
ID32 RINB2
ID33 RINB3
ID34 RINB4
ID35 RINB4
ID36 RINB3
ID37 RINB2
ID38 RINB1
Modules Replacement: 1. Disconnect main power. 2. Locate module and remove mounting nuts. 3. Disconnect module power cable from harness. 4. Route wire from new light through hole and connect to harness. 5. Replace module and secure with previous mounting method. 6. Restore power to bar and test new module to ensure functionality. 7. Configure the ID of the replacement module through the PC app.*
FOR MORE HELP WITH SOFTWARE PROGRAMMING, MODULE ID SETTING AND REPLACEMENT PLEASE SCAN QR CODE FOR SOUNDOFF CENTRAL LIGHTBAR GUIDES.
FUNCTION DEFINITIONS
Mode Select: The mpower Arrow Kit is equipped with 8 selectable pattern configuration modes. The default input wire configuration allows for 6 modes and an additional 2 modes may be configured with the PC Application using any available input wires. Default is Mode 1 where the Mode select input is floating. Mode 2 is in use when the input is activated. This feature allows up to 8 completely different sets of patterns to be programmed into the Light-bar’s non-volatile memory. Once programming configuration is complete, the Mode can be changed “on-the-fly” by an activation switch which applies voltage to the Mode input wire(s).
Cruise Mode: Allows the user to program any light group(s) to “Glow” when this feature is activated. The LED intensity is selectable between 1 and 10% duty cycle. For dual / tri color bars, the color for each light group is selectable.
Takedown Mode: Allows the user to program any Light Head Group(s) to turn on steady when this feature is activated to provide steady ON takedown lighting.
Directional Arrow Built-in: The directional controller is built-in with 11 arrow patterns for each of the 3 modes (left arrow, right arrow, and center out arrow) and the color is selectable for dual / tri color bars
Steady On Mode: Accessible with PC App only and allows the user to program any light module to turn on steady at 100% duty cycle.
Stop / Tail / Turn Mode: Allows the user to program any Light Head Group(s) to operate in 2 levels of intensity for tail and stop/turn functions.
Low Power Mode: Operates lighting at reduced intensity. Selectable between 20 and 90% duty cycle.
Scene Lighting Mode: Allows the user to program any Light Head Group(s) to turn on steady when this feature is activated to provide additional scene lighting. The activation of this input also activates the Takedown function
Speed Sense Input: The breakout box has a speed sense input that is capable of sensing vehicle speed when connected to the Vehicle Speed Sense (VSS) trigger wire which is supplied in the police upfitter wire harness for some vehicles. This feature is configured using the PC configuration software utility.
Matrix Input: Matrix inputs are virtual inputs which can be triggered based on combinations of up to four physical wires or siren input signals. This feature also allows the installer to invert the state of inputs, latch momentary inputs and adjust trigger timing through on and off delay timer settings. This feature is configured using the PC configuration software utility.
11
800-338-7337 | soundoffsignal.com
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
FLASH PATTERNS
*fpm=Flashes per Minute **fps=Flashes per Second
#
SC1 SN2 SC3 SC4 SC5 SC6 SC7 SC8 SC9 SN10 SN11 SN12 SC13 SC14 SC15 SC16 SC17 SN18 SC19 SC20 SC21 SC22 SC23 SN24 SN25 SN26 SN27 SN28 SN29 SN30 SN31 SN32
Name
Random 1 Random 2
Quint Quad 2 Q-Switch Double Power Pulse Road Runner Slow Runner Warp Inter-Cycle Warp 1-2-3 E-Single E-Double E-Triple E-Single Sim E-Double Sim Super Slow Runner Quint Simultaneous Road Runner Simultaneous Quint Pass/Steady Driver Road Runner Pass/Steady Driver Quint 2 Warp 2 Inter-Cycle 2 Flicker Brake Flicker Cruise Steady Manifesto Power Evert Dazzle Quiver
SAE
ECE
Compliant Compliant
Timing
Timing
California Title 13 Compliant
Timing
Color
Sequence
fpm
fps
Yes
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
#1
Variable
–
–
No
#1
Variable
–
–
No
#1
Alternating
70
1.2
No
#1
Variable
–
–
No
#1
Variable
–
–
No
#1
Alternating
115
1.9
No
#1
Alternating
180
3
Yes
#1
Alternating
115
1.9
Yes
#1
Alternating
70
1.2
No
#1
Alternating
350
5.8
No
#1
Alternating
–
–
No
#1
Alternating
–
–
No
#1
Alternating
125
2.1
No
#1
Alternating
125
2.1
No
#1
Alternating
125
2.1
No
#1
Simultaneous
125
2.1
No
#1
Simultaneous
125
2.1
No
#1
Alternating
55
0.9
No
#1
Simultaneous
70
1.2
No
#1
Simultaneous
114
1.9
No
#1
–
70
1.2
No
#1
–
114
1.9
No
#1
–
70
1.2
No
#1
–
350
5.8
No
#1
–
–
–
No
#1
–
–
–
No
#1
–
–
–
No
#1
–
–
–
No
#1
–
–
–
No
#1
–
–
–
No
#1
–
–
–
No
#1
–
–
–
NOTE: Takedown light patterns are limited to pattern #1 25
12
800-338-7337 | soundoffsignal.com
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
FLASH PATTERNS CONT.
#
SN33 SN34 SN35 SN36 SN37 SN38 SN39 SN40 SN41 SN42 SN43 SN44 SN45 SN46 SN47 SN48 SN49 SN50 SN51 SN52 SN53 SN54 SN55 SN56 SN57 DC1 DN2 DC3 DC4 DC5 DC6 DC7 DC8 DC9 DN10 DN11 DN12 DN13 DN14
Name
Power Sway Evert
Alternating Rapid Flash Swift Impact Tango Tremble Shake Evolver Corner Sweep
Corner Sweep Slow Full/Sweep
Full/Sweep Slow Center Sweep
Center Sweep Slow Orbit
Orbit Slow Double Orbit Slow Double Orbit Retrograde Orbit Slow Retrograde Orbit Progressive Alternate
Recurrent E-Scroll ECE-Single – Aura ECE-Single – Aura II Random Dual #1 Random Dual #2 Quint Dual Quad 2 Dual Q-Switch Dual Double Dual Power Pulse Dual Road Runner Dual Slow Runner Dual Warp Dual Inter-Cycle Dual Warp 1-2-3 Dual Pattern #1 Dual Pattern #2 Dual
SAE Compliant
Timing
No No No No No No No No No No No No No No No No No No No No No No No No No Yes No Yes Yes Yes Yes Yes Yes Yes No No No No No
ECE Compliant
Timing
No No No No No No No No No No No No No No No No No No No No No No Yes No No No No No No No No No No No No No No No No
California Title 13 Compliant Timing
No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No Yes Yes No No No No No
Color
#1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2
*fpm=Flashes per Minute **fps=Flashes per Second
Sequence
fpm fps
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Simultaneous
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Simultaneous
–
–
Alternating
–
–
Alternating
–
–
Alternating
–
–
Variable
–
–
Variable
–
–
Alternating
70 1.2
Variable
–
–
Variable
–
–
Alternating
115 1.9
Alternating
180
3
Alternating
115 1.9
Alternating
70 1.2
Alternating
350 5.8
Alternating
–
–
Alternating
–
–
Variable
–
–
Variable
–
–
13
800-338-7337 | soundoffsignal.com
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
FLASH PATTERNS CONT.
#
Name
DN15 DN16 DC17 DC18 DC19 DN20 DN21 DN22 DN23 DN24 DN25 DN26 DN27 DN28 DN29 DN30 DN31 DN32 DN33 DN34 DN35 DN36 DN37 DN38 DN39 DN40 DN41 DN42 DN43 DN44 DN45 DN46 DN47 DN48 DN49 DN50 DN51 DN52 DN53
Impact Dual Explosion Dual Quint Simultaneous Dual Road Runner Sim. Dual Quint 2 Dual
Warp 2 Dual Inter-Cycle 2 Dual Super Slow Runner Dual Flicker Cruise Dual
Manifesto Dual Power Evert Dual
Dazzle Dual Quiver Dual Power Sway Dual Evert Dual Alternating Rapid Flash Dual Swift Impact Dual Tango Dual Tremble Dual Shake Dual Evolver Dual Corner Sweep Dual Corner Sweep Slow Dual Full/Sweep Dual Full/Sweep Slow Dual Center Sweep Dual Center Sweep Slow Dual Orbit Dual Orbit Slow Dual Double Orbit Dual Slow Double Orbit Dual Retrograde Orbit Dual Slow Retrograde Orbit Dual Progressive Alternate Dual Recurrent Dual E-Scroll Dual Road Runner Dual – Aura Road Runner Dual – Aura II Slow Runner Dual – Aura
SAE Compliant
Timing
No No Yes Yes Yes No No No No No No No No No No No No No No No No No No No No No No No No No No No No No
No No No No
ECE Compliant
Timing
No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No Yes No No No
California Title 13 Compliant
Timing
No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No
Color
#1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2 #1/2
*fpm=Flashes per Minute **fps=Flashes per Second
Sequence
Variable Variable Simultaneous Simultaneous
Simultaneous Simultaneous Alternating Alternating Alternating Alternating
fpm fps
–
–
–
–
70 1.2
114 1.9
70 1.2
350 5.8
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
14
800-338-7337 | soundoffsignal.com
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
FLASH PATTERNS CONT.
#
DN54 DN55 DN56 DN57 DN58 DN59 DN60 DN61 DN62 DN63 TN1 TN2 TC3 TC4 TN5 TC6 TC7 TC8 TC9 TN10 TN11 TN12 TN13 TC14 TC15 TC16 TN17 TN18 TN19 TN20 TN21 TN22 TN23 TN24 TN25 TN26 TN27 TN28 TN29
Name
Slow Runner Dual – Aura II Super Slow Runner Dual – Aura Super Slow Runner Dual – Aura II Corner Sweep Slow Dual – Aura
Full Sweep Slow Dual – Aura Center Sweep Slow Dual – Aura
Orbit Slow Dual – Aura Double Orbit Slow Dual – Aura Retrograde Orbit Slow Dual – Aura Flicker Cruise alternate Dual – Aura
Pattern 1 Tri Random Tri
Quint Tri Quad 2 Tri Pattern 2 Tri Double Tri Power Pulse Tri Road Runner Tri Slow Runner Tri Warp Tri Inter-Cycle Tri Warp 1-2-3 Tri Super Slow Runner Tri Quint Simultaneous Tri Road Runner Sim. Tri Quint 2 Tri Warp 2 Tri Inter-Cycle 2 Tri Pattern 3 Tri Flicker Cruise Tri Manifesto Tri Power Evert Tri Dazzle Tri Quiver Tri Power Sway Tri
Evert Tri Alternating Rapid Flash Tri
Swift Impact Tri Tango Tri
*fpm=Flashes per Minute **fps=Flashes per Second
SAE
ECE
California Title 13
Compliant Compliant
Compliant
Timing
Timing
Timing
Color
Sequence fpm fps
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
#1/2 Alternating
–
–
No
#1/2 Alternating
–
–
No
#1/2 Alternating
–
–
No
#1/2
–
–
–
No
#1/2
–
–
–
No
#1/2
–
–
–
No
#1/2
–
–
–
No
#1/2
–
–
–
No
#1/2
–
–
–
No
#1/2
–
–
–
No
#1/2/3 Alternating
–
–
No
#1/2/3 Alternating
–
–
No
#1/2/3 Alternating 70 1.2
No
#1/2/3 Alternating
–
–
No
#1/2/3
–
–
–
No
#1/2/3 Alternating 115 1.9
No
#1/2/3 Alternating 180 3
Yes
#1/2/3 Alternating 115 1.9
Yes
#1/2/3 Alternating 70 1.2
No
#1/2/3 Alternating 350 5.8
No
#1/2/3 Alternating
–
–
No
#1/2/3 Alternating
–
–
No
#1/2/3 Alternating 55 0.9
No
#1/2/3 Simultaneous 70 1.2
No
#1/2/3 Simultaneous 114 1.9
No
#1/2/3 Alternating 70 1.2
No
#1/2/3 Alternating 350 5.8
No
#1/2/3 Alternating
–
–
No
#1/2/3
–
–
–
No
#1/2/3
–
–
–
No
#1/2/3
–
–
–
No
#1/2/3
–
–
–
No
#1/2/3
–
–
–
No
#1/2/3
–
–
–
No
#1/2/3
–
–
–
No
#1/2/3
–
–
–
No
#1/2/3
–
–
–
No
#1/2/3
–
–
–
No
#1/2/3
–
–
–
15
800-338-7337 | soundoffsignal.com
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
FLASH PATTERNS CONT.
#
TN30 TN31 TN32 TN33 TN34 TN35 TN36 TN37 TN38 TN39 TN40 TN41 TN42 TN43 TN44 TN45 TN46 TN47 TN48 TN49 TN50 TN51 TN52 TN53 TN54 TN55 TN56 TN57 TN58 TN59
Name
Tremble Tri Shake Tri Evolver Tri Corner Sweep Tri Corner Sweep Slow Tri Full/Sweep Tri Full/Sweep Slow Tri Center Sweep Tri Center Sweep Slow Tri Orbit Tri Orbit Slow Tri Double Orbit Tri Double Orbit Slow Tri Retrograde Orbit Tri Retrograde Orbit Slow Tri Progressive Alternate Tri Recurrent Tri E-Scroll Tri Road Runner Tri – Aura Road Runner Tri – Aura II Slow Runner Tri – Aura Slow Runner Tri – Aura II Super Slow Runner Tri – Aura Super Slow Runner Tri – Aura II Corner Sweep Slow Tri – Aura Full Sweep Slow Tri – Aura Center Sweep Slow Tri – Aura Orbit Slow Tri – Aura Double Orbit Slow Tri – Aura Retrograde Orbit Slow Tri – Aura
SAE Compliant
Timing
No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No
ECE Compliant
Timing
No No No No No No No No No No No No No No No No No Yes No No No No No No No No No No No No
California Title 13 Compliant Timing
No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No
Color
#1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3 #1/2/3
*fpm=Flashes per Minute **fps=Flashes per Second
Sequence fpm fps
–
–
–
–
–
–
Simultaneous –
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Simultaneous –
–
Alternating
–
–
Alternating
–
–
Alternating
–
–
Alternating
–
–
Alternating
–
–
Alternating
–
–
Alternating
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
16
800-338-7337 | soundoffsignal.com
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
#
Name
1
Single Fast
2
Single Slow
3
Chaser Fast
4
Chaser Slow
5
Fill Fast
6
Fill Slow
7
Grow/Shrink
8
Warning w/Arrow
9
Warning w/Arrow Fill
10
Arrow Random 1
11
Arrow Random 2
12
Grow/Shrink 2
13
Single Slow – Aura III
14
Fill Slow – Aura III
FLASH PATTERNS CONT.
ARROW PATTERNS
SAE Compliant
Timing
No No No No No No No No No No No No No No
ECE Compliant
Timing
No No No No No No No No No No No No No No
California Title 13 Compliant Timing
No No No No No No No No No No No No No No
Color
#1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1 #1
Sequence fpm fps
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
SIREN FUNCTIONS
#
Button
S1
Pushbutton 1
S2
Pushbutton 2
S3
Pushbutton 3
S4
Pushbutton 4
S5
Pushbutton 5
S6
Pushbutton 6
S7
Pushbutton 7
S8
Pushbutton 8
S9 Single Button Arrow
S10
Slide Switch 1
S11
Slide Switch 2
S12
Slide Switch 3
Function
Left Arrow –
Takedown Cruise 1 Low Power 1 Scene 1
Right Arrow
Warning Warning Warning
Mods affected
Entire Bar –
Selected at Bar Creation Entire Bar Entire Bar
Selected at Bar Creation
Entire Bar Entire Bar Entire Bar Entire Bar
Color ( : if the color is not populated, it would be the next color listed)
Amber Color 1 –
White Color 1
White
No Amber Color 1
Color 1 Color 1 Color 1
Flash
Mode 2 Mode 3 Mode 4
CERT chosen
SAE/NONE
Pattern –
Slow Runner Quint
Intercycle
17
800-338-7337 | soundoffsignal.com
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
CONNECTION OF LIGHTBAR BREAKOUT BOX TO SOUNDOFF SIGNAL SIREN:
Note: Requires PC configuration app to map siren control switches to lightbar functions. Plug 1 end of RJ-45 cable to available jack on siren amplifier.
ETSA481CSR or ETSA482CSR
CN6 CN2
ETSA481RSP, ETSA482RSP, ETSA461HPP, ETSA462HPP
CN8
CN5
CN3
ETSA5100/5200
Breakout Box Lightbar
RJ-45 Splitter
Siren Controller
Breakout Box Lightbar
UNIVERSAL BREAKOUT BOX – BACK
Lightbar
SoundOff Central® Software Universal Breakout Box ID Settings
When using more than one lightbar universal breakout box (UBOB) with SoundOff Central Software, set the ID number for each UBOB using the dip switches and then configure the light bars accordingly in the Software.
1. Select Lightbars Tab on the main SETUP Page.
18
2. Under Lightbars tab, select the EXTERNAL tab 3. Hover cursor over the to open up to see UBOB list. The number after the UBOB is Universal Breakout Box ID Information. the ID needed.
800-338-7337 | soundoffsignal.com
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
mpower ARROW KIT TROUBLESHOOTING
Normal Operation
Under Normal operation with ignition input powered, the breakout box will have the Green LED ON and the Red LED light
will be ON.
GENERAL TROUBLESHOOTING
Before further troubleshooting steps, start here:
· Check power source to the Arrow Kit and breakout box (10AWG red and 22AWG red wires). · Check the ground source to the Arrow Kit and breakout box (10AWG black and 22AWG black wires). · Check ignition source to the Arrow Kit and breakout box (pink/white wire). · Check any splice and butt connections for proper crimp integrity. · Check connectors for positive engagement.
NO OPERATION
The green LED is not illuminated
· Check Power (Pin #4) and Ground (Pin #1) on the 4-pin connector. · If not connected to a 400 Series Siren or bluePRINT Controller, check Ignition (pin #12) on the 24-pin connector.
The red LED is not illuminated while inputs are active
· Verify there is proper voltage on the input wire. Many inputs are positive or negative selectable (through SoundOff Central Lightbar). · Check Arrow Kit program configuration using SoundOff Central Lightbar. Verify any active inputs are mapped to activate Arrow Kit functions.
Green and red LEDs are illuminated properly
· Verify the Arrow Kit data wires on the 4-pin connector (pin #3) is correctly connected to the Arrow Kit data wire. · Verify the data wire circuit (from the breakout box into the Arrow Kit) is not damaged or shorted to power or ground.
NO LIGHT OPERATION IN ONE ARROW KIT QUADRANT
Breakout box LED’s operating correctly; Remove top cover and follow the non-working modules wires to fuse location. If fuse is blown, check for shorts in cabling and LED module. Replace any damaged cables or modules and replace fuse. If fuse blows again, replace defective power distribution assembly.
No Steady Red LED on breakout box; Check 24-pin connector at breakout box (ensure it is snapped in correctly), check appropriate input to breakout box for output lights which should be on.
NO TAKEDOWNS LIGHTS
Breakout box LED’s operating correctly; Verify configuration and make sure light modules are configured for takedown function.
No steady Red LED on breakout box; Check 24-pin connector at breakout box (insure it is snapped in correctly), check appropriate input to breakout box for output lights which should be on.
NO OR INCORRECT WARNING LIGHTS
· Verify the configuration for proper Arrow Kit operation. · Verify the Arrow Kit data wires on the 4-pin connector (pin #3) is correctly connected to the Arrow Kit data wire. · Verify light module ID/positions.
INCORRECT OR NO ARROW OPERATION
Breakout box LED’s operating correctly; · Verify configuration and make sure light modules are configured for arrow function.
No steady Red LED on breakout box;
· Check 24-pin connector at breakout box (ensure it is snapped into position correctly), check appropriate input to breakout box for output lights which should be on.
19
800-338-7337 | soundoffsignal.com
FOR MORE HELP WITH SOFTWARE PROGRAMMING, MODULE ID SETTING AND REPLACEMENT PLEASE SCAN QR CODE FOR SOUNDOFF CENTRAL LIGHTBAR GUIDES.
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
REPLACEMENT PARTS & ACCESSORIES
2 1
3
ITEM #
1 2
3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
20
REPLACEMENT PARTS & ACCESSORIES
PART #
PMPAKHNPW1 PMPAKHNDS1
PUVBBJ00 PUVBBJC1 PEPL9BBHNS PEPL9BBHNL PEPL9BBHNXL PMPAKLMTS204(x)C PMPAKLMTS208(x)C PMPAKLMTD208(x)C PMPAKLMTT212(xxx)C PMPAKLMMS204(x)C PMPAKLMMS208(x)C PMPAKLMMD208(x)C PMPAKLMMT212(xxx)C PMPAKLMQS204(x)C PMPAKLMQS208(x)C PMPAKLMQD208(x)C PMPAKLMQT212(xxx)C PMPAKLSTS206(x)C PMPAKLSTS208(x)C PMPAKLSTD212(x)C PMPAKLSTT218(xxx)WC PMPAKLSMS206(x)C PMPAKLSMS208(x)C PMPAKLSMD212(x)C PMPAKLSMT218(xxx)C PMPAKLSQS206(x)C PMPAKLSQS208(x)C PMPAKLSQD212(x)C PMPAKLSQT218(xxx)C PMPAKLHTS206(x)C PMPAKLHTS208(x)C PMPAKLHTD212(x)C PMPAKLHTT218(xxx)WC PMPAKLHMS206(x)C PMPAKLHMS208(x)C PMPAKLHMD212(x)C PMPAKLHMT218(xxx)C PMPAKLHQS206(x)C PMPAKLHQS208(x)C PMPAKLHQD212(x)C PMPAKLHQT218(xxx)C
STEALTH PART #
PMPAKLSTS206(x)S PMPAKLSTS208(x)S PMPAKLSTD212(x)S PMPAKLSTT218(xxx)S PMPAKLSMS206(x)S PMPAKLSMS208(x)S PMPAKLSMD212(x)S PMPAKLSMT218(xxx)S PMPAKLSQS206(x)S PMPAKLSQS208(x)S PMPAKLSQD212(x)S PMPAKLSQT218(xxx)S
DESCRIPTION
VEHICLE POWER HARNESS DISTRIBUTION HARNESS UNIVERSAL BREAKOUT BOX (LIN) UNIVERSAL BREAKOUT BOX (CAN) 12″ BREAKOUT BOX HARNESS 36″ BREAKOUT BOX HARNESS 120″ BREAKOUT BOX HARNESS MPOWER 3″ 3-WIRE LIGHT w/ STUD MOUNT 4 LED SINGLE COLOR MPOWER 3″ 3-WIRE LIGHT w/ STUD MOUNT 8 LED SINGLE COLOR MPOWER 3″ 3-WIRE LIGHT w/ STUD MOUNT 8 LED DUAL COLOR MPOWER 3″ 3-WIRE LIGHT w/ STUD MOUNT 12 LED TRI COLOR MPOWER 3″ 3-WIRE LIGHT w/ SCREW MOUNT 4 LED SINGLE COLOR MPOWER 3″ 3-WIRE LIGHT w/ SCREW MOUNT 8 LED SINGLE COLOR MPOWER 3″ 3-WIRE LIGHT w/ SCREW MOUNT 8 LED DUAL COLOR MPOWER 3″ 3-WIRE LIGHT w/ SCREW MOUNT 12 LED TRI COLOR MPOWER 3″ 3-WIRE LIGHT w/ QUICK MOUNT 4 LED SINGLE COLOR MPOWER 3″ 3-WIRE LIGHT w/ QUICK MOUNT 8 LED SINGLE COLOR MPOWER 3″ 3-WIRE LIGHT w/ QUICK MOUNT 8 LED DUAL COLOR MPOWER 3″ 3-WIRE LIGHT w/ QUICK MOUNT 12 LED TRI COLOR MPOWER 4″ 3-WIRE LIGHT w/ STUD MOUNT 6 LED SINGLE COLOR MPOWER 4″ 3-WIRE LIGHT w/ STUD MOUNT 8 LED SINGLE COLOR MPOWER 4″ 3-WIRE LIGHT w/ STUD MOUNT 12 LED DUAL COLOR MPOWER 4″ 3-WIRE LIGHT w/ STUD MOUNT 18 LED TRI COLOR MPOWER 4″ 3-WIRE LIGHT w/ SCREW MOUNT 6 LED SINGLE COLOR MPOWER 4″ 3-WIRE LIGHT w/ SCREW MOUNT 8 LED SINGLE COLOR MPOWER 4″ 3-WIRE LIGHT w/ SCREW MOUNT 12 LED DUAL COLOR MPOWER 4″ 3-WIRE LIGHT w/ SCREW MOUNT 18 LED TRI COLOR MPOWER 4″ 3-WIRE LIGHT w/ QUICK MOUNT 6 LED SINGLE COLOR MPOWER 4″ 3-WIRE LIGHT w/ QUICK MOUNT 8 LED SINGLE COLOR MPOWER 4″ 3-WIRE LIGHT w/ QUICK MOUNT 12 LED DUAL COLOR MPOWER 4″ 3-WIRE LIGHT w/ QUICK MOUNT 18 LED TRI COLOR MPOWER 4″ HD 3-WIRE LIGHT w/ STUD MOUNT 6 LED SINGLE COLOR MPOWER 4″ HD 3-WIRE LIGHT w/ STUD MOUNT 8 LED SINGLE COLOR MPOWER 4″ HD 3-WIRE LIGHT w/ STUD MOUNT 12 LED DUAL COLOR MPOWER 4″ HD 3-WIRE LIGHT w/ STUD MOUNT 18 LED TRI COLOR MPOWER 4″ HD 3-WIRE LIGHT w/ SCREW MOUNT 6 LED SINGLE COLOR MPOWER 4″ HD 3-WIRE LIGHT w/ SCREW MOUNT 8 LED SINGLE COLOR MPOWER 4″ HD 3-WIRE LIGHT w/ SCREW MOUNT 12 LED DUAL COLOR MPOWER 4″ HD 3-WIRE LIGHT w/ SCREW MOUNT 18 LED TRI COLOR MPOWER 4″ HD 3-WIRE LIGHT w/ QUICK MOUNT 6 LED SINGLE COLOR MPOWER 4″ HD 3-WIRE LIGHT w/ QUICK MOUNT 8 LED SINGLE COLOR MPOWER 4″ HD 3-WIRE LIGHT w/ QUICK MOUNT 12 LED DUAL COLOR MPOWER 4″ HD 3-WIRE LIGHT w/ QUICK MOUNT 18 LED TRI COLOR
800-338-7337 | soundoffsignal.com
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
mpower® Arrow Kit
WARRANTY & RETURN GOODS PROCEDURE
MOUNTING INTEGRITY: A review of bolt/hardware/mounting bracket integrity should be performed at the beginning and end of each shift.
WARNING MESSAGES – PLEASE READ:
WARNING – CARE MUST BE TAKEN WHEN DRILLING THROUGH THE VEHICLE NOT TO DAMAGE ANY EXISTING WIRING. CHECK BOTH SIDES OF THE MOUNTING SERVICE PRIOR TO DRILLING. DE-BURR ANY HOLES AND REMOVE ANY METAL SHARDS OR REMNANTS. INSTALL GROMMETS INTO ALL WIRE PASSAGE HOLES.
WARNING – ROUTE WIRES ONLY IN LOCATIONS THAT ARE NOT SUBJECTED TO POTENTIAL WEAR. MAKE SURE TO AVOID ROUTING WIRES IN THE DEPLOYMENT AREA OF YOUR AIR BAG. REFER TO YOUR VEHICLE OWNER’S MANUAL FOR AIR BAG DEPLOYMENT ZONES.
WARRANTY RETURN PROCESS: Please scan QR code or visit https://soundoffsignal.com/support-page/returns/.
Alternatively contact your SoundOff Signal Sales Representative, Customer Services staff or our Technical Department (800.338.7337) for a RMA #, Return Merchandise Authorization Number.
The following information is required for issuance of the RMA #:
· Reason for returning the product* · Address where replacement product is to be shipped* · Telephone number where you may be reached* · SoundOff Signal invoice number on which product was
purchased** · SoundOff Signal part number and serial number** · E-mail address where RMA # should be e-mailed** · Fax number where RMA # should be faxed**
WARNING – ALL CUSTOMER SUPPLIED POWER WIRES CONNECTING TO THE POSITIVE (+) OR NEGATIVE (-) BATTERY TERMINAL OR LOCAL CHASSIS GROUND (-) MUST BE SIZED TO SUPPLY AT LEAST 125% OF THE MAXIMUM CURRENT AND PROPERLY FUSED AT THE POWER SOURCE WITH APPROPRIATELY RATED FUSE.
* RMA # will not be given without this information. ** If available, please provide this information.
SoundOff Signal will NOT accept returns without an RMA #. Each RMA # is good for only one (1) return and will expire (30) days after the date it was issued. Products must be shipped back to SoundOff Signal and the RMA # clearly marked on the outside of the package near the shipping label. Please use the following address on your shipping label:
SoundOff Signal ATTN: RMA # / Technical Services 3900 Central Parkway Hudsonville, MI 49426
WARRANTY EXCLUSIONS:
Shipping & Handling, labor and service fees are non-refundable. SoundOff Signal is not liable for any damage due to installation or personal injury as a result of using SoundOff Signal product.
WARRANTY FORFEITURE:
Warranty will not be granted if the Warranty Return Policy & Procedure rules are not strictly followed. Physical damage resulting from customer abuse will void warranty. Warranty will also be voided if any SoundOff Signal and/or manufacturer serial tags, product stickers, seals, or the like, are removed, altered or tampered with. Returned product that is damaged by shipping via the RMA # procedure is not the responsibility of SoundOff Signal.
Document effective date on cover and below supersedes previously dated policies and statements.
There are no other warranties, expressed or implied, including, but not limited to, any implied merchantability or fitness for a particular use. SoundOff Signal reserves the right to modify this warranty statement at any time; or to discontinue, modify, or upgrade any products of its manufacture with design improvements without prior notice.
21
800-338-7337 | soundoffsignal.com
mpower® Arrow Kit no bracket English 00KPJL 0425 REV C
Documents / Resources
 |
Sound off Signal EMPAKKT0 mpower Arrow Kit [pdf] Installation Guide EMPAKKT0 X, EMPAKXXXXX, EMPAKKT0 mpower Arrow Kit, EMPAKKT0, mpower Arrow Kit, Arrow Kit |