SONOFF-logo

SONOFF ZBM5-80W Zigbee Smart Wall Switch

SONOFF-ZBM5-80W-Zigbee-Smart-Wall-product

Power off

SONOFF-ZBM5-80W-Zigbee-Smart-Wall-FIG-1

AWARNING
Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector while the device is powered on!

Wiring instruction

  1. Choose no neutral required mode or neutral required mode according toyour home’s wiring.
  2. In no neutral required mode: the minimum supported load is 3W, and this device does not support other types of inductive loads such as fans.
  3. Make sure all wires are connected correctly.

No neutral required mode wiring

SONOFF-ZBM5-80W-Zigbee-Smart-Wall-FIG-2

Neutral required mode wiring

SONOFF-ZBM5-80W-Zigbee-Smart-Wall-FIG-3

Download the eWeLink App & Add SONOFF Zigbee gateway.

Scan QR Code to Add Device

SONOFF-ZBM5-80W-Zigbee-Smart-Wall-FIG-4

Open the eWeLink App and scan the QR code on the device, then follow the instructions given by the app to proceed.

SONOFF-ZBM5-80W-Zigbee-Smart-Wall-FIG-5

  • Tighten the power module to the mounting box with screws.
  • Hook the switch module’s latch into the upper groove of the met.
  • Press downward to fix the switch module in place, it will automat with the pin positions.

The equipment is only suitable for mounting at heights 2 m

Protective cover

SONOFF-ZBM5-80W-Zigbee-Smart-Wall-FIG-6

When the wall-mounting box is made of plastic and the size is small, the protective cover can be omitted.
This device can be used with the SONOFF switch frame.

Power on

SONOFF-ZBM5-80W-Zigbee-Smart-Wall-FIG-7

After powering on, the device will enter the pairing mode by default during the first use and the LED signal indicator will “flash slowly”.

The device will exit the Pairing Mode if not paired within 3 minutes. When you nant to enter the pairing mode again, long-press the button on the device for 5 seconds until the signal light “flashes slowly/’ and release.

User Manual
https://sonoff.tech/usermanuals

To ensure the safety of your electrical installation, it’s essential that either a Miniature Circuit Breaker (MCB) or a Residual Current operated Circuit-breaker Nith Integral Overcurrent protection(RCBO) with an electrical rating of 1 OA has been installed before the ZBM5-1 C-80W, ZBM5-2C-80W, ZBM5-3C-80W.

For CE frequency
EU Operating Frequency Range
Zigbee: 2405-2480 MHz
EU Output Power
ZigbeeQ0dBm

WEEE Disposal and Recycling Information+

SONOFF-ZBM5-80W-Zigbee-Smart-Wall-FIG-9
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

Warning
Under normal use of conditions, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.

ZBM5-1C-80W:
Rating: 100-240V- 50/60Hz 1 OA Max Resistive load –SONOFF-ZBM5-80W-Zigbee-Smart-Wall-FIG-10
LED: OOV
Min.load: 3W (No Neutral Required)
Net weight: 132.8g
Product dimension: 86×71 x40.3mm

ZBM5-2C-80W:
Rating: 100-240V- 50/60Hz 1 OA/gang, Total I OA Max Resistive load SONOFF-ZBM5-80W-Zigbee-Smart-Wall-FIG-10
LED: 400W@240V/gang, 200W@1 OOV/gang, Total 400W@240V, 200W@1 OOV
Min.load: 3W (No Neutral Required)
Net weight: 141.6g
Product dimension: 86×71 x40.3mm

ZBM5-3C-80W:
Rating: 100-240V- 50/60Hz 1 OA/gang, Total 1 OA Max Resistive load SONOFF-ZBM5-80W-Zigbee-Smart-Wall-FIG-10
LED: 400W@240V/gang, 200W@1 OOV/gang, Total 400W@240V, 200W@1 OOV
Min.load: 3W (No Neutral Required)
Net weight: 150.3g
Product dimension: 86×71 x40.3mm

It is suitable for safe use only when the altitude is below 2000m. Security risks may arise when the altitude is above 2000m.

Shenzhen Sonoff Technologies Co., Ltd.
3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China
ZIP code: 518000
Website: sonoff.tech
Service email: support@itead.cc MADE IN CHINA

SONOFF-ZBM5-80W-Zigbee-Smart-Wall-FIG-8

Documents / Resources

SONOFF ZBM5-80W Zigbee Smart Wall Switch [pdf] User Guide
80 Type, ZBM5-80W Zigbee Smart Wall Switch, ZBM5-80W, Zigbee Smart Wall Switch, Smart Wall Switch, Switch

References

Leave a comment

Your email address will not be published. Required fields are marked *