SonoFF Mini DIM Zigbee Dimmer Switch User Guide
Zigbee Dimmer Switch
WARNING
- Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector while the device is powered on!
- For single-phase use only (220-240V~). Connecting to multiple phases may result in damage to the device.
- To ensure the safety of your electrical installation, it’s essential either a Miniature Circuit Breaker (MCB) or a Residual Current operated Circuit-breaker with Integral Overcurrent protection (RCBO) with an electrical rating of 2A has been installed before the MINI-ZBDIM.
- It is prohibited to connect S1 and S2 terminals to the neutral or ground wire, in order to avoid damaging the equipment and causing danger.
- Make sure all wires are connected correctly.
- Supported switches are rocker switch and push button and factory default by supporting rocker switch.
Method of change the switch type:
short press the button 3 times until the LED signal indicator flashes 3 times quickly, now you change the switch type successfully.
After powering on, the device will enter the pairing mode defaulted during the first use and the LED signal indicator will “flash slowly”.
The device will exit the Pairing Mode if not paired within 3mins. When you want to enter the pairing mode again, long press the button on the device for 5 seconds until the signal light “flashes slowly” and release.
Download the eWeLink App
Add SONOFF Zigbee gateway
Add device
Open the eWeLink App and scan the QR code on the device, then follow the instructions given by the app to proceed.
If the page cannot be displayed after scanning the QR code, please click on the Zigbee gateway to which you want to add the device in the eWeLink app and select “Add”.
User Manual
https://sonoff.tech/usermanuals
Enter the website provided above to view the User Manual for the device.
EU Declaration of Conformity
Hereby, Shenzhen Sonoff Technologies Co., Ltd declares that the radio equipment type MINI-ZBDIM is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
https://sonoff.tech/compliance/
Rating: 220-240V~50Hz 400W Max Resistive load 
ε
Dimension: 45×39.4×16.8mm
WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.
| Scatola | Manuale |
| PAP 21 | PAP 22 |
| Carta | Carta |
| RACCOLTA DIFFERENZIAΤΑ | |
| Verifica le disposizioni del tuo Comune.Separa le componenti e conferiscile in modo corretto | |
For CE frequency
EU Operating Frequency Range
Zigbee: 2405-2480 MHz
BLE: 2402-2480 MHz
EU Output Power
Zigbee≤10dBm
BLE≤10dBm
Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.
Manufacturer:
Shenzhen Sonoff Technologies Co., Ltd.
Address: 3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, 518000, China
Website: sonoff.tech
Service email: support@itead.cc
00.00.07.0474 V1.0
Documents / Resources
 |
SonoFF Mini DIM Zigbee Dimmer Switch [pdf] User Guide Mini DIM Zigbee Dimmer Switch, DIM Zigbee Dimmer Switch, Zigbee Dimmer Switch, Dimmer Switch |