SonoFF APN5-BASICZB1GSP Basic Din Rail Zigbee Smart Switch User Guide

SonoFF APN5-BASICZB1GSP Basic Din Rail Zigbee Smart Switch

Scan the QR code or visit the website to learn

https://help.sonoff.tech/docs/BASIC-ZB1GSP

Power off

WARNING

• Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector while the device is powered on!
• For single-phase use only {100-240V-). Connecting to multiple phases may result in damage to the device.
• To ensure the safety of your electrical installation, it’s essential either a Miniature Circuit Breaker (MCB} or a Residu.al Current operated Circuit-breaker with Integral Overcurrent protection(RCBO) with an electrical rating of 32A has been installed before the BASIC-ZB1 GSP.

Install the device in the distribution board

Wiring instruction

1. Do not reverse the N and L port connections to avoid damaging the device and creating a hazard.
2. Make sure_all wires are connected correctly.

Power on

After powering on, the device wlll enter the pairing mode defaulted during the first use and the LED signal indicator will “flash slowly”.
The device will exit the Pairing Mode if not paired within 3mins. When you want to enter the pairing mode again, long press the button on the device for 5 seconds until the signal light “flashes slowly” and release

Download the eWelinkApp

Add SONOFF Zigbee gateway

Add Device

Open the eWelink App and scan the QR code on the device, then follow the instructions given by the app to proceed.
If the page cannot be displayed after scanning the QR code, please click on the Zigbee gateway to which you want to add the device in the eWelink app and select “Add”

FCC compliance statement

Responsible Party Name: SONOFFTECHNOLOGY LLC
Address: 14n7 NE 40th 51, Suite 201 Bellevue, WA 98007
Email Address: usres@itead.cc FCC ID: 2APN5-BASICZB1GSP

1. This device complies with part 15 of the FCC Rules. Operation is subject to the fonowing two conditions:
2. This device may not cause harmful Interference, and
3. This device must accept any interferenel!! received, including Interference that may cause undesired operation.
4. Changes or modifications not expressly approved by the party responsible for compliance could void the u!ier’!i authority to operate tne equipment

Note: Thls equipment has been t.erted and found to comply with the limits for a a ass B digital device, pursuant to part 1 5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful lnterferer.::e In a resldenllal ln..t.’lllatlon. This equipment generates, uses and can radiate radio frequency energy and, if not in!italled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interferenel!! will not occur in a particular Installation. If this equipment does cause ham,ful inrference to rlldio or tell!Vision rec,o,ption, which can be determined by tu ming the equipment off and on, the user Is encouraged to try to com,ct the interference by one or more of the following measures:

• Reorient or relocate the rerelvlng antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment Into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced rndio/TYtechnician for help,

FCC Radiation Exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment
This equipment •hould be in•talled and operated witn minimum distance of 20 011 between tne radiator and your body.
This transmitter must not be co-located or operating In conjunction with any other antenna or transmitter

WEEE Disposal and Recycling Information

All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health.
Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

EU Declaration of Conformity

Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type BASIC-ZBI GSP is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/compliance/

For CE frequency
EU Operating Frequency Range
Zigbee: 2405-2480 MHz

EU Output Power
Zigbeesl OdBm

Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.
Pollution degree: II
Rated impulse voltage: 4KV
Automatic action: 10000 Cycles
Control Type: 1 .B
Operating temperature: 15T50
Operating altitude: 2000M
Product dimension: 84×66.5x18mm
Rating: 100-240V- 50/60Hz 32A Max