SonicWall APL69-11B Wireless AC Firewall User Guide

APL69-11B Wireless AC Firewall

SonicWall® TZ80
Quick Start Guide

For product information, go to SonicWall Technical Documentation
for the TZ series.

Regulatory Model: APL69-11B
Number Product Name: TZ80

Copyright © 2024 SonicWall Inc. All rights reserved.
SonicWall is a trademark or registered trademark of SonicWall Inc. and/or its affiliates in
the U.S.A. and/or other countries. All other trademarks and registered trademarks are
property of their respective owners.
The information in this document is provided in connection with SonicWall Inc. and/or its
affiliates’ products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of
SonicWall products. EXCEPT AS SET FORTH IN THE TERMS AND CONDITIONS AS
SPECIFIED IN THE LICENSE AGREEMENT FOR THIS PRODUCT, SONICWALL
AND/OR ITS AFFILIATES ASSUME NO LIABILITY WHATSOEVER AND DISCLAIMS
ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS
PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT.
IN NO EVENT SHALL SONICWALL AND/OR ITS AFFILIATES BE
LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR
INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR
LOSS OF PROFITS, BUSINESS INTERRUPTION OR LOSS OF INFORMATION)
ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF
SONICWALL AND/OR ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. SonicWall and/or its affiliates make no representations or
warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and product
descriptions at any time without notice. SonicWall Inc. and/or its affiliates do not make
any commitment to update the information contained in this document.

Legend

WARNING: A WARNING icon indicates a potential for property
damage, personal injury, or death.
CAUTION: A CAUTION icon indicates potential damage to hardware or
loss of data if instructions are not followed.
IMPORTANT, NOTE, TIP, MOBILE, OR VIDEO: icon indicates supporting
information.

To access the Support Portal, go to https://www.sonicwall.com/support.
SonicWall TZ80 Quick Start Guide
Updated – August 2024
232-006137-52 Rev A

Package Contents

1. TZ80 Series appliance
2. 12VDC/36W Power adapter
3. Power cord
4. Ethernet cable
5. Screws (2) M3 x 4mm
6. DIN bracket
7. SonicWall TZ80 Quick Start Guide
8. Safety, Regulatory and Legal Information document
9. Safety, Environmental, and Regulatory Information document

Content missing? Contact SonicWall Technical Support at:
https://www.sonicwall.com/support/contact-support

Back Panel

1. SS /U0 U0 SS USB-A 3.0 Port: For configuration, recovery, reimaging, and WWAN.
2. CONSOLE Micro-USB Console Port
3. SS /U0 U0 SS USB-C port with screw lock: For configuration, recovery, re-imaging, and WWAN.
4. X4 X4 SFP Port: 1 Gbps
5. X3 X3 RJ45 Port: 1 Gbps
6. X2 X2 RJ45 Port: 1 Gbps
7. X1/WAN X1 WAN RJ45 Port: 1 Gbps
8. X0/LAN X0 LAN RJ45 Port: 1 Gbps
9. 12V⎓ Power Input: 36W 100~240VAC – 12VDC power adapter
10. SafeMode (located adjacent to power supply connector)
    Pin-button (Use a pin to press the button).*

* Enter SafeMode or RECOVERY.

While the system is operational, press the SafeMode button. System gracefully
reboots and enters SafeMode or RECOVERY.

While the system is powered down, press and hold the SafeMode button while
connecting the power supply. Release the SafeMode button when you see the
TEST/WRENCH LED blinking YELLOW three times to acknowledge the action.

NOTE: Only one USB port can be used at a time.

Front Panel

1. Power LED: Blue = Powered on
2. Test LED: Yellow = Initializing, blinking yellow = SafeMode
3. Security LED: Green = All security services licensed,
   blinking yellow = Security services license expired
   Security Services monitored by this LED:
   Gateway Anti-Virus, Intrusion Prevention, Anti-Spyware
4. X0 LAN/MGMT X0 Port LED: Solid green = link up,
   blinking green = link activity
5. X1 WAN X1 Port LEDs: Solid green = link up,
   blinking green = link activity
6. X2 RJ45 Port LEDs: Solid green = link up,
   blinking green = link activity
7. X3 RJ45 Port LEDs: Solid Green = link up,
   Blinking Green = link activity
8. X4 SFP Port LEDs: Solid Green = link up,
   Blinking Green = link activity
9. U0 WWAN LEDs for USB 5G/LTE: Green = 5G/LTE signal
   strength

Mounting Options
Flat Surface Option

Place the TZ80 on a flat surface. Allow unrestricted airflow around
the unit, leaving at least one inch (25.44 mm) clearance on all sides.

Alternate Mounting Option

Instead of using a rack mount tray to mount your TZ80 and power
adapter in a standard 19-inch rack, you can mount a DIN bracket to
the bottom of your TZ80 using the two M3*4mm screws provided and
hang it from one of the rails in your rack.

Connect Power

CAUTION: Only use the power adapter included with this
device. Do not use a power adapter that is damaged or
from another device.

Connect Interfaces

Connect the WAN interface (X1) on the back of the TZ80 to the
Internet.

Setup and Registration

IMPORTANT: The TZ80 must be licensed before it can be
configured or used.

IMPORTANT: The TZ80 must always be connected to the Internet. It
cannot be used in a closed network environment.

Local Management

Set up and manage your TZ80 by connecting it to a management
computer with an Ethernet cable.
To minimize scrolling, set your screen resolution to at least 1920 x
1080 pixels.

1. Connect the TZ80 LAN interface (X0) to your computer.
Your computer should be configured to accept DHCP
addressing.
2. Navigate to https://192.168.168.168 in your web
browser and log in with the default credentials:
l Username: admin
l Password: password
3. On successful login using the default password, you are
then prompted to change the password.
NOTE: The default password must be changed at the time
of your first log in and the new password to be used for
future login attempts.
4. Launch the Setup Guide wizard or manually configure to
complete initial configuration.
5. Using SonicOS, click Register and log in with your
MySonicWall credentials to register your TZ80.

Your TZ80 is now initialized and ready for use!

Cloud Management

Use SonicWall Capture Security Center (CSC) with Zero Touch to
manage and configure your TZ80.

NOTE: This option requires a Cloud Management license.

1. Log into CSC at cloud.sonicwall.com using your
MySonicWall credentials.
2. Select the MySonicWall tile to register your TZ80.
3. Enable Zero Touch and NSM licensing on your TZ80 in
MySonicWall.
4. Select the Network Security Manager tile in CSC to
manage your TZ80 from the cloud.

SonicExpress App

Use SonicWall SonicExpress on your smart phone to register and
configure your TZ80.

NOTE: After initial setup, be sure to download the latest firmware
from MySonicWall and upgrade your TZ80.

1. Download and launch the SonicExpress App on your iOS or
Android device.
2. Tap Login and log in with your MySonicWall credentials,
then select the tenant for the . Tenants can contain multiple
SonicWall appliances.
3. Connect your iOS or Android device to the TZ80 with your
smartphone USB cable (not supplied with the TZ80).

4. Use the SonicExpress Setup Guide to register the TZ80,
synchronize service licenses, change the password, and
configure essential interface settings.

Documents / Resources

SonicWall APL69-11B Wireless AC Firewall [pdf] User Guide APL69-11B, APL69-11B Wireless AC Firewall, APL69-11B, Wireless AC Firewall, AC Firewall, Firewall

References

• User Manual