Solutions MS-TP Programmable Touch Panel
Copyright Notice
All contents of this manual, whose copyright belongs to our corporation cannot be cloned, copied or translated without the permission of the company.
Product specifications and information which were referred to in this document are for reference only. We may change, delete, or update any content at any time and without prior notice.
FCC Notice
This product complies with Part 15 of the FCC Rules. The operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause undesired operation.delete, or update any content at any time and without prior notice.
This product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/television technician for help.
Class A ITE
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B ITE limits. Such equipment should not be restricted in its sale but the following warning shall be included in the instructions for use:
Warning
Operating this equipment in a residential environment may cause radio interference.
EC Compliance Statement
(Class A)
This product is herewith confirmed to comply with the requirements set out in the Council Directives on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility Directive 2014/30/EU.
Surge Protection
This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lighting strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of
your equipment..
Caution
The network cable connection method required for this product is direct connection. Please do not cross-connect.
Introduction
The MS-TP programmable touch panel, designed for automated office systems, multimedia rooms, and smart homes, features a configurable interactive user interface and intelligent networking capabilities. This wall-mounted panel, compatible with standard 86-box installations, includes a 720×720 capacitive touchscreen and one RS-232 serial port. It supports diverse applications across industries, including multimedia conference rooms, multi-functional halls, training centers, showrooms, broadcasting studios, and industrial automation.
Key Features
- ARM Cortex-A55 architecture 1.8Ghz
- Android 11.0 system, 4GB DDR4 RAM, 32GB EMMC Flash
- 4 inch 720*720 (1:1) resolution, capacitive touch screen, standard 86 box wall-in design
- Dual-mode operation – functions as either a touchscreen central control or a user terminal.
- Customizable interface and function configuration through PC software
- Compliant with industry standard network communication protocols (TCP/IP, Http, UDP, Websocket)
- Standard 1Gbps network port
- Dual power supply mode, supporting POE or an independent DC power supply
Package Contents
- A1x Programmable Touch Panel (Wall-in)
- 1x 3pin-3.81mm Phoenix Connectors (male)
- 1x 24V/1A Multinational Power Supply (2pin-3.81mm Phoenix Connector)
- 1x Wall Mounting Bracket
- 2x Bracket Fixing Screw
- 1x User Manual
Specifications
| Technical | |
| CPU: | ARM Cortex-A55 1.8GHz |
| Operating system: | Android 11 |
| RAM: | 4GB DDR4 RAM |
| Flash memory: | 32GB EMMC Flash |
| Resolution: | 720*720 |
| Touch type: | Capacitive Touch Screen |
| ESD protection: | IEC 61000-4-2: ±8kV (Air-gap discharge) & ±4kV (Contact discharge) |
| Connection | |
| RS232: | 1x 3-pin Phoenix Connectors |
| LAN/POE: | 1x Standard 10M/100M/1000M Ethernet RJ45 port, supporting POE function |
| POWER: | 1x 2-pin Phoenix Connectors, for power supply or POE |
| DEBUG: | 1x Micro USB, system debugging port |
| Mechanical | |
| Housing: | Front Pane: Touch Screen; Frame: A uminum A oy Rear Case: P astic |
| Color: | Front Pane: Back; Frame: Gray Rear Case: White |
| Dimensions: | 86mm (L) x 86mm (W) x 44mm (D) |
| Weight: | 192g |
| Power supply: | 24V DC/1A or POE |
| Power consumption: | 5W |
| Operating temperature: | 0°C ~ 40°C / 32°F ~ 104°F |
| Storage temperature: | -4°F ~ 140°F / -20°C ~ 60°C |
| Operating humidity: | 20% ~ 80% (relative humidity, non-condensing) |
| Storage humidity: | 10% ~ 90% (relative humidity, non-condensing) |
Operation Controls and Functions
| Number | Name | Function Description |
| 1 | Touch screen | Capacitive touch screen. The user contro interface can be configured through the configuration too . |
|
2 |
RESET button |
Reboot: After the device boots up, press and ho d the RESET button for more than 1s
less than 5s, then release it, the device wi reboot. The device won’t upload the user projects after rebooting. Reset: After the device boots up, press and ho d the RESET button for more than 5 seconds, then release it, the device writes the user configuration information. The IP wi be restored to the default settings (IP address: 192.168.0.101, subnet mask: 255.255.0.0), the ogin password of the management page wi be initialized to “admin”, the device time wi be initialized to automatic acquisition mode, but user projects won’t be deleted by factory initialization. |
| 3 | POWER button | Used for screen off or wake-up. |
| 4 | USB port | Micro USB port. The reserved port for system debugging. |
|
5 |
LAN/PoE port |
Standard 10M/100M/1000M Ethernet RJ45 port with default auto-negotiated speed for device connection, projects uploading & down oading, network communication and debugging. By default, the DHCP function of the contro pane is disabled, and the IP setting is as follows: IP address: 192.168.0.101, subnet mask: 255.255.0.0 |
| 6 | POWER port | The power input port (2-PIN phoenix connectors), used for connecting with externa 24V DC power supply. |
|
7 |
RS232 port |
Programmable RS232 seria port, which is a 3-pin phoenix connector (ma e), compliant with RS232 communication protocol. The pin-outs of the RS232 port are PIN1 for TX, PIN2 for GND, and PIN3 for RX. |
Mounting Instructions
This wall-in touch panel can be mounted on a standard 86 wall box, the mounting steps are as follows:
Step 1: Install the included wall mounting bracket onto the 86 wall box and fasten it with 2 screws.
Step 2: Align the back of the touch panel with the slots of the wall bracket and push it in. Press the aluminum edge of the touch panel to ensure that the buckles are in place, and the installation is complete.
To remove the mounted touch panel, insert a screwdriver into the two holes indicated by the arrows and pry the machine out of the bottom box.
FAQ
Q: Can I use this touch panel without surge protection?
A: While surge protection is highly recommended, the touch panel can function without it. However, using surge protection will extend the equipment's lifespan.
Q: What type of network connection is required for this product?
A: The product requires a direct network cable connection method. Do not cross-connect the network cables.
Documents / Resources
 |
Solutions MS-TP Programmable Touch Panel [pdf] User Guide MS-TP Programmable Touch Panel, MS-TP, Programmable Touch Panel, Touch Panel, Panel |