Battery Monitoring WiFi Stick
“
Specifications:
- Product: SOLUNA WiFi Stick
- Model: VerA3
- Compatibility: iOS and Android devices
Product Usage Instructions:
Step 1: Stick Logger Installation
Assemble the logger to the device communication interface as
shown in the diagram. Note the notch at the interface.
Step 2: Check Indicator Light
Lights Implication:
- Light keeps on: Logger connected to the device.
- Light off: Connection to the device failed.
- On 100ms/Off 100ms (Fast flash): Communicating with
device.
Warning: Please remove logger after power
off.
Download APP:
- Method 1: Download the iOS version by searching for “Soluna
eCloud” on the App Store. - Method 2: Download the Android version by searching for “Soluna
eCloud” on Google Play. - Method 3: Log in to ecloud.solunabattery.com to
download the Android version.
FAQ:
Q: What do I do if the Stick Logger is running abnormally?
A: Check if the connection between logger and
device is loose. Remove the stick logger and install it again.
Ensure that the device matches the stick logger’s communication
rate.
Q: How do I know if the Stick Logger is running normally?
A: The Stick Logger is running normally if the
light flashes on 1s/Off 1s (Slow flash). You can also long press
the Reset button for 5s to reboot the stick logger.
“`
SOLUNA WiFi Stick Quick Guide
VerA3
Notice:
Abnormal State Processing
Please read this manual carefully before using products and keep it in the place where O&M providers can easily find.
Due to product upgrade and other factors, the content of this manual might change from time to time. Please take actual product as standard and get latest manual from soluna. Unless otherwise agreed herein, this manual will only be used as guidance. Any statement,information or suggestion in this manual will not take any form of responsibility.
Step2: Check Indicator light
Lights Implication
Status Description(All lights are single green lights.)
Without written permission, any content of this document (partly or entirely) cannot be extracted, copied or transmitted in any form by any company or individual.
1. Light keeps on: Logger connected to the
device.
Communication
with device
2. Light off: Connection to the device failed.
3. On 100ms/Off 100ms(Fast flash):
Communicating with device.
Warning: Please remove logger after power off.
1. Light off: Connection to the router failed.
2. On 1s/Off 1s(Slow flash): Connection to
the router succeeded. Communication
with router
3. Light keeps on: Connection to the server
succeeded.
4. On 100ms/Off 100ms(Fast flash): Distributing network fast.
If the data on platform is abnormal when the stick logger is running, please check the table below and according to the status of indicator lights to complete a simple troubleshooting. If it still can not be resolved or indicator lights status do not show in the table below, please contact Customer Support.(Note: Please using the following table query after power-on for 2 mins at least.)
Fault COM NET STAT Description
Fault Cause
Solution
OFF
Any state
Slow flash
Communicate with device abnormally
1. Connection between stick logger and device loosen.
1. Check the connection between stick logger and device. Remove the stick logger and install again.
2. Device does
not match with 2. Check device’s
stick logger’s communicat
communication ion rate to see if
rate.
it matches with
stick logger’s.
Download APP
Method 1: Download the iOS version by searching for
Logger running status
1. Light off: Running abnormally.
2. On 1s/Off 1s (Slow flash): Running normally.
3. Long press Reset button for 5s, reboot stick logger.
the keyword “Soluna eCloud”” on the App Store.
Method 2: Download the Andriod version by searching for the keyword “Soluna eCloud”” on the Google Play.
1. Stick logger 1. Check if the
The normal operation status of the stick logger,
ON
OFF
Slow
Connection between logger
does not have a network.
flash and router abnormal
2. Router WiFi signal strength
wireless network configured.
2. Enhance router WiFi
when router connected to the network normally
weak.
signal strength.
Method 3log in to https://ecloud.solunabattery.com 1. Connection to the server succeeded: NET light
download the Andriod version
keeps on after the logger powered on.
2. Logger running normally: STAT light flashes.
Stick Logger Installation
3. Connection to the device succeeded: COM light keeps on.
Step1: Assemble logger to the device communication interface as shown in the diagram.(Note the notch at the interface)
1. Router
1. Check if the
networking
router has
Connection abnormal.
access to the
between logger
network.
and router ON Slow Slow normal,
flash flash connection
2. The server point of logger is modified.
2. Check the router’s setting,
between logger
if the connection
and remote 3. Network
is limited.
server abnormal.limitation, server
cannot be
3. Contact our
connected.
customer
service.
OFF OFF OFF
Power supply abnormal
1. Connection between stick logger and device loosen or abnormal
2. Device power insufficient.
3. Stick Logger abnormal.
1. Check the connection, remove the stick logger and install again.
2. Check device output power.
3. Contact our customer service.
Any Fast Any Networking state flash state status
Normal
1. Exit automatically after 5 mins.
2. Long press Reset button for 5s, reboot stick logger.
3. Long press Reset button for 10s, restore factory settings.
Any Any Fast Restore factory state state flash settings
Normal
1. Exit automatically after 1 mins.
2. Long press Reset button for 5s,reboot stick logger.
3. Long press Reset button for 10s,restore factory settings.
USER MANUAL for Soluna APP Please make sure Bluetooth and WiFi are ON and the router can connect to the network normally.
Open the Soluna ecloud APP, click the “Register” button, enter your email address to receive a verification code, complete the remaining information in the dialog box, and you’ll see a message saying “Congratulations, registration successful,” allowing you to proceed to the next step.
Click on “Create Plant,” fill in the necessary information in the dialog box, and click “Save.” If the creation is successful, the app will automatically proceed to the next step. You can leave optional fields blank.
Click the confirmation option, scan the QR code on the WIFI stick (you can also enter the SN manually), then it will prompt that the addition is successful and proceed to the next step.
If configuration failure occurs, please check the following reas on and try it again.
1) Make sure WLAN is ON. 2) Make sure WiFi is normal. 3) Make sure wireless router does not implement the white-black list. 4) Remove the special characters in Wi-Fi network. 5) Shorten the distance between the phone and device. 6) Try to connect to other Wi-Fi.
1. Automatic Template Download: When you first enter Local Debugging, the latest template will be automatically downloaded.
2. Update Template: Tap the template button to manually update and download the latest template.
3. Download via QR Code: You can also download the template by scanning the template QR code located in the upper right corner.
4. Network Configuration
Step 1: To configure the network, start by checking the network configuration status. Ensure that the Bluetooth and WiFi on your mobile phone are turned on, and make sure your mobile phone is connected to the correct WiFi network.
Note 5G WiFi is not supported. Special characters (e.g., ; ” = ‘) are not supported in the router name and password.
Step 3: Please wait a few minutes. Once the success message appears, click “Done.”
1. Access Local Debugging: Tap “Local Debugging” in the “My” interface at the bottom of the app.
Note: If there is no wireless network available, you can query and modify battery parameters and upgrade the battery through the Bluetooth local debugging function.
Local Debugging
2. Download Template Engine: When using the local debugging function for the first time, the app will automatically download the template rendering engine to load the template data.
3. Automatic Updates: The template engine will iterate over time, gaining more powerful functions. These updates will be applied automatically during subsequent uses.
1.Template engine rendering
Step 4: The battery information will be displayed after five minutes.
The firmware in the system can be downloaded through the firmware management
Step 2: On the Plant Overview page, tap the button in the top right corner, then select “Configure Network.” Check the box next to the serial number, click “Start Configuration,” choose the correct WiFi network, enter the WiFi password, and click “Start Configuration” again.
You can still use Local Debugging even if the app is not logged in.
Connect the Device: Use Bluetooth to connect the device. Once the connection is successful, you’ll be able to perform the following actions. 1. Read parameters
You can read the device parameters to view its current settings and status. 2. Set parameters Modify the specified parameters to adjust thedevice’s configuration as needed.For example: modify the communication protocol.After selecting the protocol, click the button in the upper right corner. 3. Upgrade the firmware Perform an OTA (Over-the-Air)firmware upgrade toupdate the device’s software.The upgrade takes about 6 minutes
Documents / Resources
 |
SOLUNA Battery Monitoring WiFi Stick [pdf] User Guide VerA3, Battery Monitoring WiFi Stick, Monitoring WiFi Stick, WiFi Stick |