WiFi Stick Datalogger Quick
Installation Manual
Version: 3.1

Delivery Content

• 1 WiFi stick
• 1 WiFi Antenna
• 1 Quick Installation Manual

Install the datalogger

Connect the data logger to the corresponding 4-pin COM port of the inverter. A Solis 5K inverter is used here as an example.
Please follow the instructions below:
Install the datalogger:

1. Install the antenna to the datalogger
2. Insert the datalogger to the inverter COM port
3. Rotate the black circle clockwise

NOTE
Only rotate the black circle, not the sliver cover.

NOTE

1. The device must be installed away from the strong magnetic field produced by large electrical appliances such as microwave ovens, refrigerators, telephone, metal walls, etc. Otherwise, the communication quality may be affected. It may also be affected by lighting storms.
2. The [RESET] button on the back is used for the connection.
   •Short press will send the data immediately.
   •Long press for 5 seconds will reset the connection.
   The three constantly ON LED lights indicate the datalogger is working normally.

LED Lights Status:

LED indicators	Description	LED Status	Meanings
Internet Indicators •(NET)	Shows the connection status between the datalogger and the server.	Flashing	Trying to connect with the server
		ON connected	Successfully
		OFF	Abnormal connection
Inverter COM Indicators •(COM)	Shows the connection status between the datalogger and the inverter.	Flashing	Trying to connect with inverter
		ON	Successfully connected
		OFF	Abnormal connection
Power Indicator •(PWR)	Shows the power supply status of the datalogger.	ON	Datalogger is powered up normally
		OFF	Datalogger is powered up abnormally

WiFi Configuration

Step 1: Use your phone to scan the QR code to download and register the Solis Cloud APP. Or directly download from APP Store or Google Play Store by searching “SolisCloud”.

SolisCloud

Step 2: If it is a new data logger, please configure it first, then click the “Willi configure”.

Step 3: Manually fill in the datalogger SN or Scan the SN on the datalogger.

Step 4: Click ” “, make sure the phone is connected to router WiFi, and switch back to the page to fill in the WiFi password, then move to the next step.

Step 5: Long press the “Reset” button for 5 seconds until the yellow and green LEDs are quickly flashing. Then click the “It’s flashing”.

Step 6: Wait for around 10 seconds. After the configuration is completed, click ” “and back to the main page. If failed, re-do the configuration process or contact the after-sale engineers.

Create the Soliscloud Account

Step1: Select Owner or Installer for email address registration.

Step2: Enter your account and password, then click the “Register”.

Create Plant

Stepl: Enter the main page of the Soliscloud APP, and click the “Add plant” at the bottom.

Step 2: Input the information about the plant as required. Then click “Done“.

Step 3: Confirm the plant information.
Click “Create a plant”.Step 4: Click “View plant” to enter the plant homepage, then add the datalogger.

Step 5: Scan the SN number of the datalogger or manually input it.
Note: Scan the datalogger SN, NOT the inverter SN.

Step 6: Plant creation succeeds. Click “Continue…datalogger” to check the monitoring data. If the plant has multiple data loggers, please click “View Plant”.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Contact
Please contact us if you have any technical problems in terms of the product. Please provide the following information as well:

• Inverter SN
• Datalogger SN
• Problem Description

Ginlong Technologies Co., Ltd.
No. 57 Jintong Road, Binhai Industrial Park, Xiangshan, Ningbo, Zhejiang, 315712, P.R.China.
Tel: +86 (0)574 6578 1806
Fax: +86 (0)574 6578 1606
Email : info@ginlong.com
Web : www.ginlong.com

Documents / Resources

solis S3-WIFI WiFi Stick Datalogger [pdf] Installation Guide S3-WIFI, S3WIFI, 2AWE8-S3-WIFI, 2AWE8S3WIFI, S3-WIFI WiFi Stick Datalogger, WiFi Stick Datalogger

References

• User Manual