SOLIGHT PP124C Built in Socket with USB Fast Charger
Product Usage Instructions
- Specify the position on the table where you want to insert the socket module. Ensure there is at least 120mm space under the table top for successful installation.
- Mark a round hole with a diameter of 60mm and drill a hole not exceeding 62-63mm in diameter.
- Insert the socket module, adjust the bottom nut, and seal with transparent silicone sealant to prevent liquid leakage.
- Plug the device power cable into an electrical outlet.
- Use a power socket with 230V AC, current load max. 16A / total power consumption max. 3680W.
- Power cable type: H05VV-F 3G 1.0mm2, length 2m.
- Intelligent circuit adjusts charging current based on connected devices’ batteries and state of charge, max. total charging current is 3.4A.
- Slide the top cover to access the USB charging adapter or the 230V socket.
- Attach or detach power or USB cables as needed.
- Do not dismantle the product or change connections, avoid exceeding permissible load, clean when disconnected from mains, and allow to dry thoroughly to prevent damage or injury.
FAQ
- Q: Can I connect multiple devices simultaneously for charging?
- A: Yes, you can connect two devices to both USB ports (Type-A and Type-C) at the same time. The intelligent circuit adjusts the charging current based on the device batteries and the state of charge.
PP124C-PD20, PP124CB-PD20
Built-in socket with USB Fast charger
Introduction
- Thank you for purchasing our equipment.
- Please read this manual carefully and heed the safety warnings and instructions before installing, using, or repairing the equipment.
- This will ensure not only the protection of persons but also the long life of the equipment.
INSTALLATION
- specify the position on the table where you want to insert the socket module. Installation is not recommended too close to the edges to ensure board strength and load. If it is a chipboard table, wrap the area around the position with insulating tape. For a successful installation, there must be at least 120mm space under a tabletop or a board top.
- mark a round hole with a diameter of 60mm. Drill a hole using the most suitable tools, such as a jigsaw. Max. diameter created should not exceed 62-63mm.
- Insert the socket module, adjust the bottom nut, and tighten. It is best to seal the block before liquids leak with a transparent silicone sealant.
- finally, plug the device power cable into an electrical outlet.
MAINS SUPPLY
- power socket 230V AC, current load, and total power consumption max. 16A / max. 3680W.
- power cable type H05VV-F 3G 1.0mm2, length 2m (visible 1.9m).
USB CHARGING OUTPUTS
- USB-A (QC3.0): DC 5.0V
3.0A, 15.0W, 9.0V2.0A, 18.0W, 12.0V1.5A 18W Max, Fast Charge. USB-C (PD): DC 5.0V3.0A, 15.0W, 9.0V2.22A, 20.0W, 12.0V1.67A 20.0W Max, Power Delivery. USB A+C: DC 5.0V 3.4A 17.0W Max. - when two devices are connected to both USB ports (Type-A and Type-C) at the same time, the intelligent circuit detects their batteries, adjusts the charging current, and changes the charging speed depending on their capacity and state of charge. The maximum charging current is determined by the type of USB port, max. 3.4A in total.
- the charging time corresponds to the capacity and the state of charge of the battery of the connected device.
USAGE
- slide the top cover to expose only the USB charging adapter or also the 230V socket.
- attach or detach power or USB cables.
WARNING
- Do not dismantle the product or change the connection, do not exceed the permissible load, clean disconnect from the mains, and allow to dry thoroughly.
- Solight Holding s.r.o. in no event shall be liable for property damage or personal injury caused by improper connection or improper use.
- The product has been issued with a CE declaration of conformity under the applicable regulations.
- On request from the manufacturer: info@solight.cz, or downloadable at www.solight.cz
PARAMETERS
- Input: 16A / 250V~ ,50Hz
- Output: max. 3680W / 230V~
- USB Input: 230V~, 50Hz
- USB Output:
USB-A (QC3.0): DC 5.0V3.0A, 15.0W, 9.0V2.0A, 18.0W, 12.0V1.5A 18W Max, Fast Charge. USB-C (PD): DC 5.0V3.0A, 15.0W, 9.0V2.22A, 20.0W, 12.0V1.67A 20.0W Max, Power Delivery. USB A+C: DC 5.0V3.4A 17.0W Max.
- USB Output:
- Working temp.: 0°C (32°F) – 35°C (95°F)
Manufacturer
- Solight Holding, s.r.o., Na Brně 1972,
- Hradec Králové 500 06, Česká republika
USB charging
- Average active efficiency: 83.7%
- Efficiency at low load (10%): 78,1%
- No-load power consumption: 0.06W
Tools Required
Overview
Dimension
CONTACT
- Solight Holding, s.r.o., Na Brno 1972, Hradec Králové 500 06, Czech Republic.
Documents / Resources
 |
SOLIGHT PP124C Built in Socket with USB Fast Charger [pdf] Instructions PP124C-PD20, PP124CB-PD20, PP124C Built in Socket with USB Fast Charger, PP124C, Built in Socket with USB Fast Charger, Socket with USB Fast Charger, USB Fast Charger, Fast Charger |
