Solid Apollo Mega Power 4 Zone Remote and Controller

Quick Setup
- Insert 3 AAA batteries into the remote (match polarity to the (+) and (–) symbols).
- Wire the controller: confirm the power supply is set to 12–24V DC and is unplugged, strip about 1/4 of cover on supply wires, secure positive to the controller’s “input” positive slot and negative to the “input” negative slot, then connect the LED fixture to the controller’s output ports (match +/– as indicated on the wiring diagram).
- Do not exceed max wattage ratings: 240W @24V DC or 120W @12V DC.
- Reinstall the controller end caps, then plug in the power supply. The LED fixture turns on automatically.
- Pair remote to controller: turn on the remote, then on the controller tap the learning key once; quickly slide a finger around the remote brightness wheel. Lights blink when properly paired.
- To pair a controller to a specific zone: after turning on the remote, press the desired zone button before tapping the controller learning key and sliding around the brightness wheel.
- Operate: use the power button to turn paired lights ON/OFF; use the brightness wheel and fine-tuning to adjust brightness; press and hold saved scenes to store brightness and click to recall; use zone controls to select or toggle a zone.
Product Description
Solid Apollo’s Mega Power 4 Zone Remote and Controller is designed to wirelessly control up to 4 different zones independently.
The Mega Power 4 Zone includes the remote control unit and one zone 10A dimming-controller that can drive up to 240W at 24V DC from one output.
Product Features
- 1 x Mega Power Remote
- 1 x 10A Controller
- Control up to 4 zones
- Remote can pair to unlimited number of dimming-controllers (one included)
- Power up to 240W on a single output
- 50 feet wireless range
- Soft On/Off technology
- Full wireless dimming control
- Easy installation and operation
- Memory Function – Remembers last setting before losing power
Product Specs
Mega Power Remote
- Dimming : 100% to 10%
- Battery Type : 3 AAA Batteries
- Control System : Radio Frequency
- Frequency : 868/915/434 MHz
- Range : 50ft
- Dimension : 4.7” x 1.9” x 0.7”
Dimming-Controller
- Input Voltage : 12V – 24V DC
- Max Power : 120W@12V DC 240W@24V DC
- Max Amps : 1 x 10A
- Dimensions : 5.7″ x 1.9″ x 0.6″
- IP Rating : IP20
- Working Temp : 32F – 104F
- Warranty : N/A
- Certificates : CE, RoHS
Installation
The Mega Power 4 Zone remote and controller can control any single color LED lighting fixture running from 12V to 24V DC. After the installation is complete, you can add controllers to any of the four available zones and fine tune brightness levels. Setting up the controller system:
Tools Required
- 3 AAA Batteries for Remote Control
- Phillips and/or Flathead Screwdriver
- Flat Head Screwdriver
INSTALLATION
Setting up the controller system:
This section will show you how to wire the controller.

- Remove the white plastic end caps on both ends of the controller using the Phillips or flathead screwdriver. This will expose the green wiring slot blocks.
- To add power to the controller, first make sure the power supply uses the correct voltage (12-24V DC). Make sure the power supply is not plugged in. Take the wires coming from the power supply and, using wire strippers, strip off approximately 1/4” of cover from the end of the wires. Twist the exposed metal wires to help make a secure connection.

- On the top left green wiring slot block labeled for input, use the flathead screwdriver to rotate the positive wiring screw counterclockwise to open the wiring slot located below the screw. The screw will not come out.

- Take the positive wire and insert the exposed metal end into the positive wiring slot located below the screw. Place the wire inside until the wire stops against the wall inside the positive wiring slot. Take the flathead screwdriver and turn the positive wiring screw clockwise until the screw is snug. The positive wire has now been secured to the controller and should not come out. If it does come out, repeat from steps three and four, and place the exposed metal wire further into the positive wiring slot.

- Repeat steps three through four for the negative wire from the power supply. The negative wire will go into the negative wiring slot.

- On the right side of the controller, connect the LED fixture, being careful to match the correct wires with the matching ports. Connect the positive and negative wires as noted on the wiring diagram on page 4. Please Note: Do not exceed the Max Wattage ratings: 240W@24V DC, 120W@12V DC

- The wiring for the controller is now complete. Place the white end caps back on the controller and screw them down securely using the Phillips or flathead screwdriver.

- Plug in the power supply to the wall outlet. The LED fixture will turn on automatically. The unit is now ready to pair with the Mega Power 4 Zone Remote Control.
Controller Wiring Diagram

Adding Batteries to Mega Power 4 Zone Remote:
This section will show you how to install the batteries in your new Mega Power 4 Zone Remote.
- On the backside of the remote, open the battery cover door located at the bottom of the unit. The Mega Power 4 Zone remote uses 3 AAA Batteries to operate. When replacing, make sure the polarity is correctly oriented and matches the positive (+) and negative (-) symbols printed inside the battery area.
Pairing the remote with the controller:
This section will show you how to pair your remote with the controller and pair controllers to a specific zone.

- To pair the Mega Power 4 Zone remote with the matching controller, first make sure the controller is connected and has power running to it and that the lights are connected to the controller and turned on.

- Turn the remote on using the power button on the top left. The red light in the center of the brightness wheel will be lit when the remote is powered on. On the controller, tap the learning key button once. Then on the remote, quickly slide your finger around the brightness wheel. The lights will blink when properly paired with the remote.

- To pair a controller to a specific zone, after turning on the remote, press the desired zone button before tapping the learning key on the controller and quickly sliding your finger around the brightness wheel.

remote control
Operating the remote control:
This section will show you how to operate the Mega Power 4 Zone remote.
- A. Power – Turns all paired lights ON/OFF.
- B. Brightness Wheel – Touch sensitive wheel to select brightness level.
- C. Brightness Fine Tuning – Increase or decrease brightness at measured intervals or hold to gently ramp brightness.
- D. Saved Scenes – Press and hold to save desired brightness as a scene. Click to recall saved brightness level. One brightness level can be saved in each scene and used across zones.
- E. Zones – Click number before pairing to select zone to pair controller to. Click to choose zone to control. Hold to turn ON/OFF all lights in corresponding zone.

Troubleshooting
- If you are having problems with the lights responding to the remote, first check that the remote control is within range of the controller (50 feet maximum).
- Check that the lights in the zone are on, and the wiring to and from the controller matches the diagram on page 4.
- If there is power going to the controller, but the lights do not shine when turned off and on, or do not respond to brightness controls, the entire zone may be turned off. Hold the zone button associated with the lights to turn ON/OFF the desired zone.
- If the lights are still not responding, you can reset the controller by holding the learning key until the lights flash, and re-pair the controller to the remote following the steps on page 5.
- If the lights are still not responding, replace the three AAA batteries in the back of the remote control.
Technical Information
Remote
- 50 ft wireless range
- Requires three AAA batteries (not included)
Controller
- Input Voltage: 12V – 24V
- Max Power: 120W (12V) / 240W (24V)
- One 10A channel
- Memory Function when Power Off
- Size: 5.7” x 1.9” x 0.6”
If you have any further questions, please contact us by phone or email using the contact information
Troubleshooting
- If the lights don’t respond to the remote, check that the remote is within 50 ft maximum range of the controller.
- Confirm the lights in the selected zone are turned on and that wiring to/from the controller matches the wiring diagram.
- If power is reaching the controller but the lights won’t turn on/off or won’t respond to brightness controls, the entire zone may be turned off—hold the zone button associated with the lights to turn that zone ON/OFF.
- If the lights still don’t respond, reset the controller by holding the learning key until the lights flash, then re-pair the remote using the pairing steps.
- If the issue continues, replace the three AAA batteries in the back of the remote control.
MORE INFO
- Toll Free: 866.592.3873
- Email: info@solidapollo.com
- www.SolidApollo.com
Documents / Resources
![]() | Mega Power 4 Zone Remote and Controller |
References
- Solid Apollo LEDwww.solidapollo.com
- User Manualmanual.tools

