zalman Z9 ICEBERG MS Atx Mid Tower Computer Case

• To ensure safe and easy installation, please read the following precautions.
• Product design and specifications may be revised to improve quality and performance without notice.
• www.zalman.com

Precautions

• Read this manual carefully before installing.
• Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
• Wear gloves to prevent accidents when installing the product.
• Severe damage may occur when mounting the system, so do not apply excessive force.
• Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
• Be careful not to block the ventilation hole of the product when using the system.
• Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
• Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
• Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
• Store and use the product out of children’s reach.
• Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
• The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.

Specifications

Model		Z9 Iceberg MS
Case Form Factor		ATX Mid-Tower
Dimensions		478 x 245 x 496 (H)mm
Weight		9.6kg
Case Materials		Steel, Tempered Glass, Plastic
Motherboard Support		E-ATX / ATX / mATX / Mini-ITX
Maximum VGA Length		390mm
Maximum CPU Cooler Height		185mm
Maximum PSU Length		270mm
PCI Expansion Slots		7+3(65mm)
Drive Bays	3.5″	2 x 2.5” SSD/HDD or 3.5” HDD
	2.5″	3 x 2.5” SSD/HDD or 2 x 3.5” HDD
Fan Support	Top	3 x 120mm / 2 x 140mm
	Front	3 x 120mm / 3 x 140mm / 2 x 200mm(H: 25mm)
	Rear	1 x 120mm / 1 x 140mm
Fan(s) Included	Front	3 x 140mm ARGB Fan
	Rear	1 x 140mm ARGB Fan
Radiator Support	Front	120mm, 140mm, 240mm, 280mm, 360mm
	Top	120mm, 140mm, 240mm, 280mm, 360mm
	Rear	120mm, 140mm
Dust Filter	Top / Front / Bottom
I/O Ports		USB3.0 x 2, USB2.0 x 2, USB3.1 Gen2 Type-C x 1, MIC, HD Audio, LED Button, Reset Button, Power Button with HDD LED

Accessories component

ASSEMBLING

I/O Ports

#	Part	#	Part	#	Part	#	Part
ⓐ	Power Button with LED Light	ⓑ	USB 3.0 Ports	ⓒ	USB 2.0 Ports	ⓓ	Microphone Jack
ⓔ	Headphone Jack	ⓕ	Reset Button	ⓖ	LED Button(1)	ⓗ	USB3.1 Gen2 Type-C

1. LED control button for optional LED fans.

Rremoving the side panels

Removing the dust filter

Removing the front panel

Mounting the motherboard

Motherboard size

Mounting PCI-E(VGA) card

Removing the cable cover

Graphic card holder

Mounting the 2.5″ SSD

Mounting the 3.5″ and 2.5″ SSD / HDD

Mounting the 3.5″ and 2.5″ SSD / HDD

Flexible mount of SSD/HDD installation bracket(according to PSU length)

Mounting the PSU

Mounting the radiator

Mounting the fans

Fan(s) Included / Fan Specifications

Dimensions	140 x 140 x 25(T)mm
Bearing	Sleeve Bearing
Input	DC 12V
Max.Fan Speed	900±10%RPM
Max.Fan Air Flow	43.26CFM
Max.Fan Noise Level	21.44dB(A)
Fan	3-Pin
LED	3-Pin(Addressable RGB)

I/O Connectors

Certification

• This mark, designed by Zalman, indicates product compliance with the European Union’s RoHS (Restriction of Hazardous Substances) Directive.

Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate collection systems)

• www.zalman.com

Documents / Resources

zalman Z9 ICEBERG MS Atx Mid Tower Computer Case [pdf] User Manual Z9 ICEBERG MS Atx Mid Tower Computer Case, Z9 ICEBERG MS, Atx Mid Tower Computer Case, Tower Computer Case, Computer Case, Case

References

• User Manual