zalman P50 DS ATX Mid Tower Computer Case User Manual
* To ensure safe and easy installation, please read the following precautions.
* Product design and specifications may be revised to improve quality and performance without notice.
Precautions
- Read this manual carefully before installing.
- Check the product and components before installing. If you find any abnormalities, contact the location where you purchased the product for a replacement or refund.
- Wear gloves to prevent accidents when installing the product.
- Do not apply excessive force, as severe damage may occur when mounting the system.
- Always refer to the manual when connecting cables, as incorrect installation may cause a short circuit and fire.
- Be careful not to block the ventilation holes of the product when using the system to avoid overheating.
- Avoid areas with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated area.
- Do not use chemical cleaners, such as organic solvents like alcohol or acetone, to clean the product’s surface.
- Do not insert your hand or other objects into the product during its operation, as this may injure your hand or damage the object
- Store and use the product out of children’s reach.
- Our company assumes no responsibility for any problems that occur due to the use of the product for purposes other than its designated purposes and/or the carelessness of the customer.
- The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.
Specifications
| Model | P50 | P50 DS | |
| Case Form Factor | ATX Mid-Tower | ||
| Dimensions | 480(L) x 240(W) x 512(H) mm | ||
| Weight | 10.5kg | 11.2kg | |
| Case Materials | Plastic, Steel, Tempered Glass | ||
| Motherboard Support | ATX / mATX / Mini-ITX | ||
| Maximum VGA Length | 435mm | ||
| Maximum CPU Cooler Height | 178mm | ||
| Maximum PSU Length | 225mm | ||
| PCI Expansion Slots | 7 | ||
| Drive Bays | 3 x Combo(3.5’’ or 2.5’), 2 x 2.5’’ | ||
| Fan Support | Top | 3 x 120mm / 2 x 140mm | |
| Side | 3 x 120mm | ||
| Rear | 1 x 120mm / 1 x 140mm | ||
| Bottom | 3 x 120mm | ||
| Fan(s) Included | Top | – | – |
| Side | – | 3 x 120mm (ARGB Fan) | |
| Rear | – | 1 x 120mm (ARGB Fan) | |
| Radiator Support | Top | 120mm / 140mm / 240mm / 280mm / 360mm | |
| Side | 120mm / 240mm / 360mm | ||
| Rear | 120mm / 140mm | ||
| I/O Ports | Power, Power LED, Reset, 1 x USB Type-C, HD Audio, 2 x USB 3.0, Monitoring Cable(P50 DS) | ||
Accessories component
- User’s Manual
- Cable Ties x 5
- Glass Cleaner
- Standoff Tool x 1
- Fan Screws x 12
- HDD/SSD Anti-Vibration rings x 8
- Riser cable Stand-offs x 4
- MB Screws x 18
- HDD Screws x 8
- SSD Screws x 16
- PSU / VGA Screws x 6
- Motherboard Standoffs x 4
- Female clips x 6 (spare parts)
- VGA Holder (P50 DS)
I/O Ports
| # | Part |
| ⓐ | USB 3.0 |
| ⓑ | Microphone Headphone Jack |
| ⓒ | USB Type-C |
| ⓓ | Reset & LED Button |
| ⓔ | Power Button |
ⓕ It is possible to switch from the LED button to the Reset button by adjusting the cable connections.
ARGB controller
※ Caution : Please do not connect ARGB fans more than 8pcs, otherwise it may cause malfunction.
How to control RGB LED
- LED colors & patterns can be changed by pressing the LED Button on I/O ports.
- Long pressing on the LED Button for 6 seconds, RGB LED will be turn off after blinking twice in white.
- Long pressing on the LED Button for 3 seconds, RGB will be synchronized with motherboard after blinking once in white.
Press the LED Button again to desynchronize with motherboard.
A : ARGB LED 1~4 / 3-Pin
B : ARGB LED Control Button / 2-Pin
- Connector to ARGB LED Control Button
C : Other Motherboards Sync / 3-Pin
- Connector to Motherboard
- Requires Motherboard that Supports RGB Sync
※ Caution: if Addressable 3 Pin connects to 12V header instead of 5V header improperly, It may cause fatal damages to the product by the overvoltage
D : SATA Power / 15-Pin
- Connector to PSU
- Input : 5V
E : Connect the ARGB connector to the RGB hub
System monitoring function
*To operate the system monitoring function, please connect the monitoring cable to the pin header of the motherboard USB 2.0 ports.
Removing the side / front panels
Removing the top cover / bottom dust filter
Motherboard installation
Motherboard size
- ATX
- mATX
- Mini-ITX
Graphic card installation
2.5’’ and 3.5’’ SSD / HDD installation
HDD
SSD
PSU installation
Removing the PSU cover
Radiator installation
- Installing the top radiator ・120mm / 140mm/ 240mm / 280mm / 360mm
- Installing the side radiator・120mm / 240mm / 360mm
- Installing the rear radiator ・120mm / 140mm
Fan installation
- Installing the top fans ・3 x 120mm, 2 x 140mm
- Installing the side fans ・3 x 120mm
- Installing the rear / bottom fans ・1 x 120mm, 1 x 140mm / 3 x 120mm, 2 x 140mm
Fan(s) Included(P50 DS)
I/O Connectors
Software
Give visit ZALMAN official website (https://www.zalman.com) to find the corresponding product software and install it.
Supported operating system : win 10 and above
Certification
This mark, designed by Zalman, indicates product compliance with the European Union’s RoHS (Restriction of Hazardous Substances) Directive.
Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate collection systems)
Developed and designed by ZALMAN in Korea.
This product is protected by ZALMAN’s pending or registered patents.
www.zalman.com
Documents / Resources
 |
zalman P50 DS ATX Mid Tower Computer Case [pdf] User Manual P50, P50 DS, P50 DS ATX Mid Tower Computer Case, P50 DS ATX, Mid Tower Computer Case, Tower Computer Case, Computer Case |
