USER’S GUIDE
CONTACT US:
WORKSHAPTOOLS.COM
800.597.6170
SCAN:
FOR VIDEO TRAINING
RESOURCES
Re-Ordering Materials:
PP0003966 – WSKO-SS Mat
PP0003975 – Instruction Booklet
SA0003968 – Abrasives Kit
SA0003970 – Supplies Kit
Help Requests:
Call Tech Support – 800.418.1439
Call Darex Sales Team – 800.597.6170
Email Darex Sales Team – info@darex.com
ADDITIONAL TRAINING RESOURCES
TOUR OF THE SHARPENER
- REFERENCE PLATE
- ANGLE INDICATOR
- TENSIONER ASSEMBLY
- ANGLE SELECTION CLAMP KNOB
- SHORT CENTER DISTANCE
- LONG CENTER DISTANCE
- LOCK OUT BUTTON
- VARIABLE SPEED SWITCH
SUPPLIES KIT
1 Microfiber Cloth
1 Cleaning Brush = SA0003970
1 Pair of Safety Glasses
ABRASIVE KIT
10 P120 Sharpening Belts = SA0003968
10 X4 Honing Belts
BELT INFORMATION
 |
 |
|
| Grit | P120 | X4 |
| Color | Red | White |
| Abrasive | Coarse 120 | Fine 3000 |
| Use | Sharpen | Hone |
SET UP
1| Pull the sharpening station out.
2| Plug it in.
- Sharpening Unit
- Supply and Abrasive Kits
- Honing Unit
1| Start with the Sharpening Unit (red belt). Turn on power at medium speed and press switch lock out button.
- Lock Out Switch
2| Place spine of the blade flat onto reference plate. While keeping blade flat, move up onto belt surface and place the heel of the blade edge onto the abrasive.
- KNIFE
a: Spine
b: Primary Bevel
Use very light pressure on belt (1/16” deflection).
- KNIFE
3| Move blade flat across abrasive (1” per second) and stop with the tip on the middle of the belt. Then pull blade back and away from the belt.
4| Continue sharpening the same side of the blade until a burr is raised along entire edge (count strokes).
5| Repeat same number of strokes on other side of blade.
6| Use other sharpener to hone the blade using X4 honing belt.
⇒
P120 X4
EXPANDED EDUCATION
EDGE PROFILE
Choose either short or long center location for pulley depending on preference.
Shorter Location
Longer Location
ANGLE ADJUSTMENT
Set the desired edge profile angle. Then Move the Angle Adjustment Lever to the desired setting. Tighten Angle Selection Clamp Knob to secure.
- Angle Selection Clamp Knob
BELT CHANGE
1| Push in and turn tensioner clockwise to install / uninstall belt.
Push Tensioner in
Turn Tensioner to lock into position
Release Tensioner once belt is in place
2| Use tracking knob to center belt on pulley.
BEST TECHNIQUES
| Use light pressure while sharpening.
| Sharpen until you get a burr with the P120 belt.
| Keep both sharpeners at the same angle.
| Always use medium speed.
| Stop the blade tip on the middle of the belt.
| Sharpening Process:
| FACTORY | IN PROCESS | CONTINUE TO NEXT GRIT |
 |
 |
 |
| Most knives are flat ground and have a smaller bevel height or surface area. | Re-sharpening to a lower angle and a convex grind takes time. | Sharpen until a burr is raised before switching to a finer grit belt. |
| Use cleaning brush to keep machine clean.
| Use cloth to keep knives clean.
| Replace belts every 50-75 sharpenings.
| During heavy grinding, do not over-heat the blade.
| Do not over-tension belt or it may negatively affect belt tracking. If Over-Tension Mark is visible, lower tension.
- Over Tension Mark
| Follow the cruve of the knife when sharpening for best results.
Position belt at the very start of the edge then stop tip on belt.
TROUBLESHOOTING
PROBLEM: Knife not getting sharp.
- Take more strokes: Grind all the way to the edge. Continue until a burr is raised. Then progress to the finer belt.
- Use a higher speed: Slow belt speeds may not be removing enough material.
PROBLEM: The tips of my knives are becoming rounded.
- Solution 1: Stop the tip on the belt.
- Solution 2: Keep the blade edge perpendicular to the belt. To reduce tip rounding, follow the curve of the blade.
Follow the shape of the blade so the edge remains perpendicular to the belt. Stop on belt.
PROBLEM: How do I feel for a burr at the cutting edge to know when to proceed to the finer belt?
- Solution: Slide your finger perpendicular and away from the cutting edge. The burr will feel like a small ‘ridge’ or ‘wire’ at the edge.
- Feeling for a burr
FAQs
The premium Norax belts last on average about 50-75 sharpenings per belt.
Simply color the edge of your blade with a marker, make 1 pass using the fine grit belt and see how closely you match the bevel.
25° is a common edge angle for most pocket knives.
Use only the fine grit belt on the flat side of the edge. Teeth should be facing away from the direction of the belt. Hold near flat to remove burr. Watch training video for demo.
Obviously a sharp edge of any type is better than a dull edge and ‘better’ is a matter of opinion. While a highly polished convex edge cuts very cleanly with little resistance, a flat ground edge is still capable of accomplishing most cutting tasks. A convex edge provides the most durable edge at a given angle and has less drag compared to other edge grind types due to smooth transition lines.
Call 800.418.1439 and reference Part # SA0003968 to order replacement belts.
SHARPENING CENTER INSTRUCTIONS
CONTACT US FOR ADDITIONAL SUPPORT:
DAREX, LLC
210 E. Hersey St.
Ashland OR 97520
USA
1.800.597.6170
PP0003975 REV0
Documents / Resources
 |
WORK SHARP WSKO-SS Elite Knife Sharpening Solution [pdf] User Guide WSKO-SS Elite Knife Sharpening Solution, WSKO-SS, Elite Knife Sharpening Solution, Sharpening Solution, Solution |
