WiZ 9290032837 Camera Module

Product briefing

WiZ Camera module is offered as a Connected module which can be integrated into Luminaire, offering the Home Monitoring proposition next to Connected lighting.

Mounting reference

Dimension

Connection (flying cable)

Product interfacing info

ID Overview

Electrical information

Input voltage	SVdc +/- 5%
Current/Power	2A/10W	RMS=3.3W, peak=6.2W (Max)
Over voltage protection	12Vdc max.
Protection against electric shock	Class 2, SELV
Radio Frequency	2400M Hz-2483.SM Hz	EU: 1-13 channel NAM : 1-11 channel
Radio Transmission power	20dBm for NAM 16dBm for E.U.
Wi-Fi communication range	150 meters	Line of Sight

Mechanical information

Overall Dimension (main body)	97mmx 67mm x35mm
Color	Black
Housing Material	PC
Net weight per piece	120g
Ingress Protection	IP54, Wet location
Connection	Flying cable, 30 cm
Connectors	PH2.0 2P, PH2 .0 6P
Strength relief	>= SON

Environment and approbation

Operation temp	-20°C…+45°C
Storage temp	-40°C…+70°C
Operation relative humidity	0°C/10°C90%RH, +45°C80%RH no condensation
Storage relative humidity	+70°C 24 hrs / -40°C ٓno condensation 24hrs / +70°C 95%RH 24 hrs
Approbation	WFA, UL, CB, RED, FCC/IC
Hazardous substances compliance	ROHS, REACH compliant
Warranty	2 years
Anti-UV	Optical parts (Lens cover, light sensor etc.): t.E<2, transmissivity degradation <2%, Reflectivity degradation<2%), No impact for image quality and day/night scenes switch . Other parts: t.E<6; Significant reduction in mechanical strength and pulverizing, embrittling, peeling, obvious color change are not allowed.

Others

LED indicator	Red, Green
Button	Tack switch
SD card	Micro-SD card support up to 1TB	Not included
Interface 8pin	UART_TX(white), UART_RX(orange), GPIO_01 (green), GPIO_02(purple), GND(black), USB_DP(blue), USB_DM(brown), 5V(red)
Startup time	1min cold start at -20°C, 45 seconds at 2s°C

Outdoor IP Camera

• Two Megapixel CMOS sensor and supports up 10 meters night vision high power IR LED for true day/ night mode capability
• It features 802.11 b/g/n single band Wi-Fi for clearer 2.4GHz frequency and increased bandwidth
• Provides H.264 video compression codec
• 2-way audio with 2W speaker and built-in omni-directional microphone

Processors and Memory

Optical

Video

WIFI

Antenna

Audio

Audio Power Amplifier

Speaker

Microphone

IO Ports

Others

Environment

Ordering information

Important notes for design-in

1. The WiZ camera module works only with WiZ V2 app.
2. The WiZ camera module should be powered with a Limited Power Supply (LPS) only according to UL IEC 62368 or equivalent. Please consult WiZ for more details if necessary.
3. It is the manufacturer’s responsibility of end products to ensure the full compliance of the final integration applications (i.e end products).
4. Please clean the camera lens gently with a cotton cloth and avoid touching the lens with hands directly to ensure clear view.
5. Please regularly clean the dust on microphone and speaker to ensure 2-way audio quality.
6. The WiZ camera module does not provide third-party monitoring or emergency response. It is the user’s responsibility to determinate the appropriate response.
7. The WiZ camera module is limited to a user’s own, private residential use.
8. The user is responsible to comply with privacy and other applicable laws.

(WEEE dustbin logo and explanation)

Simplified EU Declaration of Conformity

Hereby, Signify declares that the radio equipment type WiZ camera module is in compliance with the Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.wizconnected.com.

Simplified UK Declaration of Conformity

Hereby, Signify declares that the radio equipment type WiZ camera module is in compliance with the Radio Equipment Regulations 2017 (S.I. 2017 /1206). The full text of the UKCA declaration of conformity is available at the following internet address: www.wizconnected.com

FCC compliance statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with FCC RF exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm (8 inches) between the device and user body.

ISED compliance statement

This device complies with Innovation, Science and Economic Development Canada {ISED) licence-exempt RSS standard (s). Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Documents / Resources

WiZ 9290032837 Camera Module [pdf] Instruction Manual 9290032837 Camera Module, 9290032837, Camera Module, Module

References

• User Manual