WI-AP416 In-Wall Wireless Access Point
Installation Guide
Quick Installation Guide
Cloud Managed In-wall Wireless Access Point
WI-AP416
www.wireless-tek.com
Package Contents
Interface and Indicators
LED Indicator Instructions
| Name | Status | Description |
| System LED Light | LED light blinking | System is starting |
| LED light is always on | System started successfully | |
| LED lights Off | Working abnormally/Power off/LED is turned off. |
Ports Instructions
| Action | Description |
| LAN | LAN port which can connect LAN device. |
| WAN | The port is used to connect to the PoE switch, for both data transmission and Power over Ethernet (PoE) through an Ethernet cable. |
| Reset | With the device powered on, press and hold the reset button for about 8 seconds, then release the button. The device will restore to factory default settings. |
Typical Connection
Device Installation
Wall Plate Installation
- Detach the faceplate of the AP with a screwdriver.
- Connect the Ethernet cable inside the junction box to an RJ45 plug.
- Insert the enclosed screws and tighten them with a screwdriver to secure the mounting bracket.
- Press the faceplate of the AP back into position.
Configuration Method
Method 1. Connect computer to the wireless signal of AP, the default SSID is “WI-TEK xxxx”. Password is 88888888
Method 2. Connect computer to the AP by Ethernet cable.
Step 1. On the computer, please set the static IP under the same subnet with AP, 192.168.1.xx.
Step 2. Please launch a browser such as Google Chrome or Firefox, type 192.168.1.88 into address bar and click on enter to get in the login page of wireless access point. The default login password is “admin”.
Step3. After get in the management page,On the left side menu, please go to [Wizard] to setup the access point.
Step 4. Select the appropriate operation mode and follow the instruction of wizard to finish the settings. If already exist a Router in your network, please choose, Fit AP mode; if not, you can hoose Wireless Router mode Notice: if you do a reset, AP will recovery to Fit AP mode.
·Fit AP Mode Default Login IP:192.168.1.88 admin/admin 
·Wireless Router Mode Default Login IP:192.168.11.1 admin/admin
Cloud Management Settings
Step 1. Launch your web browser then enter http://cloud2.wireless-tek.com in the address bar.
Step 2. Register an account password by user name or email.
Step 3. log in to the cloud account with the account password after registration.
After the login is successful, the steps to bind the device on the cloud account are as follows:
(1) Click ADD NETWORK
(2) Fill in the group name and location, click save. 
（3) And click next.
(4) Enter serial number, click ADD to create and click FINISH,the configuration is complete.
Note:The 17-digit SN code of the Add device is shown on the sticker on the back of the device.
(5) In the relevant device options, you can see the bound device information. 
（6) Click Tunnel, Select binding device type, click EWEB to log in to the device.
Warranty Card
| Username | |
| Address | |
| Telephone No. | |
| Purchase Shop | |
| Purchase Address | |
| Product Model No. | |
| Purchase Time | |
| Serial No. | |
| Dealer Signature |
If the product defects within three months after purchase, we will provide you a new product of the same model.
If the product defects within the three-year warranty period, we will provide the professional maintenance service.
Proof of purchase and a complete product serial number are required to receive any services guaranteed as part of the limited warranty.
Any other defects that are not caused by workmanship or product quality, such as natural disaster, water damage, extreme thermal or environmental conditions. sticker damaged, warranty card losing will disqualify the product from limited warranty.
Wireless-Tek Technology Limited
Address: Biaofang Technology Building 402, Bao’an street,
Baoan District,Shenzhen City, Guangdong, China
Website:www.wireless-tek.com
Tel:86-0755-32811290
Email:sales@wireless-tek.com
Technical Support:tech@wireless-tek.com
Documents / Resources
 |
Wi-Tek WI-AP416 In-Wall Wireless Access Point [pdf] Installation Guide WI-AP416 In-Wall Wireless Access Point, WI-AP416, In-Wall Wireless Access Point, Wireless Access Point, Access Point, Point |