X2-C ChatterBox 24P Long Range Communicator
“
Product Information
Specifications:
- Model: Chatterbox X2-C
- Features: Bluetooth, FM Radio, Bike to Bike Communication,
Rider to Passenger Communication - Battery: Rechargeable Li-ion battery
- Charging Time: Approximately 5 hours
Product Usage Instructions
1. Getting Started
Thank you for purchasing the Chatterbox X2-C. Below are the
steps to get started:
- Unpack and inspect all contents listed in the manual.
- Ensure all parts are present and undamaged.
2. Battery Usage
The X2-C comes with a rechargeable Li-ion battery pre-installed.
Follow these steps for battery maintenance:
- Discharge the battery completely by leaving the unit on until
drained. - Charge the battery fully using the provided charger
(approximately 5 hours). - If storing the unit, fully charge the battery and follow the
pre-conditioning process before next use.
3. Bike to Bike Communication
For bike to bike communication, follow the instructions in
section 3 of the manual.
4. Rider to Passenger Communication
To communicate between rider and passenger, refer to section 4
in the manual.
5. Bluetooth Feature with Audio Control
Explore the Bluetooth feature and audio control options as
detailed in section 5 of the manual.
6. FM Radio
To use the FM radio feature, follow the steps outlined in
section 6 of the manual.
7. Putting It All Together
Refer to section 7 for a comprehensive guide on using all
features together.
Frequently Asked Questions (FAQ)
Q: Can I replace the battery myself?
A: The X2-C comes with a pre-installed rechargeable Li-ion
battery. It is recommended not to open the case to replace the
battery. Please follow the provided instructions for battery
maintenance.
“`
Table of Contents
1. GETTING STARTED ……………………………………………………………………………………………… 3
WHAT’S NEW?…………………………………………………………………………………………………………………………………..3 UNPACKING AND INSPECTION ……………………………………………………………………………………………………………….3 BATTERY …………………………………………………………………………………………………………………………………………4 INSTALLATION OF HEADSET, MAIN UNIT, AND WIRED PTTB (PUSH TO TALK BUTTON) …………………………………………4
2. GETTING TO KNOW YOUR X2-C …………………………………………………………………………… 5
BUTTONS AND INPUTS…………………………………………………………………………………………………………………………5 LCD DISPLAY …………………………………………………………………………………………………………………………………..7 SHORT PRESS JOG BUTTON………………………………………………………………………………………………………………….7 DOUBLE PRESS JOG BUTTON ………………………………………………………………………………………………………………..7 MULTIPLE DEVICE MODES ……………………………………………………………………………………………………………………8
3. BIKE TO BIKE COMMUNICATION ………………………………………………………………………….. 8
POWER ON/OFF: ………………………………………………………………………………………………………………………………8 SET VOLUME LEVEL……………………………………………………………………………………………………………………………9 CHOOSE A CHANNEL FOR THE GROUP …………………………………………………………………………………………………….9 SIDE TONE ……………………………………………………………………………………………………………………………………….9 USING THE VOICE ACTIVATION FEATURE(VOX)…………………………………………………………………………………………9
4. RIDER TO PASSENGER COMMUNICATION……………………………………………………………. 9
LISTENING TO BIKE TO BIKE COMMUNICATION………………………………………………………………………………………… 10 RIDER AND PASSENGER ONLY COMMUNICATION ……………………………………………………………………………………. 10
5. BLUETOOTH FEATURE WITH AUDIO CONTROL ………………………………………………….. 10
BLUETOOTH FEATURE……………………………………………………………………………………………………………………… 10 PAIRING……………………………………………………………………………………………………………………………………….. 10 PAIRING MULTIPLE DEVICES ……………………………………………………………………………………………………………… 10 USING SMARTPHONE TO GET MUSIC, PHONE, AND NAVIGATION …………………………………………………………………. 11 REMOTE CONTROL …………………………………………………………………………………………………………………………. 12
6. FM RADIO………………………………………………………………………………………………………….. 12
TURN ON/OFF THE FM RADIO……………………………………………………………………………………………………………. 12 CHANGE VOLUME …………………………………………………………………………………………………………………………… 12 SEARCH FM RADIO STATIONS …………………………………………………………………………………………………………… 12
7. PUTTING IT ALL TOGETHER ………………………………………………………………………………. 12
TYPICAL SETTING …………………………………………………………………………………………………………………………… 12 PRIORITY ……………………………………………………………………………………………………………………………………… 13 SUMMARY OF BUTTON FUNCTIONS ……………………………………………………………………………………………………… 13 TECHNICAL SPECIFICATION ………………………………………………………………………………………………………………. 14
ChatterBox
Page 2 of 15
1. Getting started
What’s new?
Thank you for your recent purchase of the Chatterbox X2-C. The X2-C is the replacement model for our current flagship X2Slim-p. The X2Slim-p has always been favored by riders for all of its advanced features. Per your request the X2-C is smaller and lighter with even more features. The following is a detailed comparison chart that shows the new features of the X2-C.
Features Wireless PTT Bike to Bike two way communication among unlimited riders 22 Channel with 38 talk groups for each channel Hands free voice activation or push to talk capability Rider to passenger communication capability Share music Two way communication with passenger(open group talk) Answer phone calls and listen to music wirelessly True Hi-Fi stereo speakers and noise suppression microphones 8 hours of talk time and 20 hours of standby FM Radio Headset with microphones for open and full face helmets including modular Cradle with headset and microphone support for clean install Control Knob for easier rider support
X2-C Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
X2Slim-p Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
Unpacking and inspection
Please check and make sure that you have everything listed below inside the box. If you find any parts missing or that have been damaged, please contact our customer service immediately.
1
X2Slim Unit with Battery pre-installed
3
Multi microphone Headset which includes microphones
for open and full face helmets, two Velcro speaker disks,
two foam microphone covers, and microphone Velcro
ChatterBox
Page 3 of 15
5
Helmet mounting bracket with Cradle, two screws and
Allen wrench.
Battery
The X2-Cm comes with a rechargeable Li-ion battery pre-installed inside of the unit. Please do not attempt to open the case to replace the battery.
We recommend that the battery be pre-conditioned to restore to the original state.
1) Discharge the battery completely by leaving the unit on until the battery is completely drained
2) Charge the battery completely using the charger supplied with the kit. It should take about 5 hours to fully charge the battery.
If you are planning to store the unit for a long period of time, store it after fully charging the battery. Upon using it again, please follow the pre-conditioning process described above.
To reduce the risk of damage to the battery, do not use any other charger except the one supplied with the kit. Make sure the battery is always stored at room temperature.
Battery indicator in the LCD display means as followed:
Indicator 3 Bars 2 Bars 1 Bar
Means Fully charged Half charged Low charged
When the battery indicator shows 1 bar, you need to charge the battery. Or you can hear a chime sound when it is time to charge the battery.
Installation of headset, main unit, and wired PTTB (Push to talk button)
The Multi Headset comes with both open and full face microphones. Choose the one that you intend to use and plug it into the connector on the cradle. Please keep the microphone that you are not using in a safe place for future use. All microphones come with foam cover. For full face helmet, attach soft Velcro disk to the helmet chin bar and hard Velcro disk to the microphones.
The headset speakers should already have Velcro on the back casing. Simply apply the soft Velcro disks on the liner of your helmet. Mount them in the indentation of the helmet padding where your ears would line up. Please keep in mind that you need to mount the speakers in a location that is directly next to your ears.
ChatterBox
Page 4 of 15
Attach the right speaker (with the longer wire) to the corresponding Velcro disk that you applied on the helmet liner. Attach the left speaker (with the shorter wire) to the other Velcro disk. For helmets with speaker pockets, simply insert the speakers in each corresponding pocket. Use the wooden wire tuck stick to gently tuck all wires between the headliner and the shell of the helmet as shown below. If you helmet has washable lining that pops out, you can tuck the wires behind that.
Fasten the mounting bracket snugly to the bottom left side of the helmet with two bolts supplied. Align the back side of the X2Slim unit to the grooves on the mounting bracket. Slide the X2Slim unit down on the mounting bracket until it latches firmly into place.
Insert the 3.5mm plug of the headset into the Rider’s headset jack on the bottom of the cradle.
2. Getting to know your X2-C
Buttons and inputs
The X2-C is packed with many features in a light compact casing. Please refer to the picture below which will show each button and its description.
ChatterBox
Page 5 of 15
Buttons & Inputs
Description These are brief descriptions of the buttons and inputs. Detailed descriptions and specific instructions will be provided later in the manual
1 PTT(push to talk )
1) Transmit to other riders or your passenger. 2) Press the power button and PTT button at the same time for pairing wireless PTT
3) Return to Communication Mode in the Setup Status
2 Power Button Turn the X2-C on and off
3 LED window
Represents the state of Bluetooth pairing
4 Driver MIC(Cradle)
5 LCD 6 Jog
button/Dial
Rider MIC Input
Displays the status of each mode 1) Access the different mode functions. 2) Answer and end the phone calls 3) Choose the FM radio stations. 4) Volume up/down
7 Passenger Ear Input for Passenger Headset
Jack
8 Charger
Wall charger port
9 Driver
Rider Headset Input
Headset(Cradle)
Multi-function buttons: Jog button handles more than one function.
pressing the buttons in order to control the different functions of the X2-C.
Long press
Press the button and hold it for 3 seconds
Double Press
Press briefly twice within half seconds
Short Press
Press the button for half second
The following are 3 ways of
ChatterBox
Page 6 of 15
LCD Display
The X2-C is equipped with an LCD display that shows the status of the X2-C. The table below shows the icons and what they mean.
Description Sensitivity Bluetooth VOX FM Radio
Intercom
Battery meter Music
Talk Group Type Wireless PTT Talk group Channel
Appears when;
(Shows the strength of the received signal) (Unit is paired to a Bluetooth device)
You long press Jog button
You press the Jog button shortly twice and turn the Jog dial to FM Radio mode You press the Jog button shortly twice and turn the Jog dial to Intercomm mode (Shows status of battery power)
You press the Jog button shortly twice and turn the Jog dial to Music Play mode (Indicates that the sub-channel is in use)
( Unit is paired to a Wireless PTT )
(Shows talking group number) (Shows Channel number)
short press Jog button
If you press the Jog button on the Communication Mode enters the Setup state. Setup state is used to choose the desired function setting. The table below shows the different settings that you can use along with a brief description.
Press Jog button
1 time
Setting control for:
Channel
2 times Talk Group
3 times 5 times
6 times 7 times
vox
Voice calling
LCD Display
Description of current state
Blinks Antenna
bar Sub-chann
el no.
Blinks vox
Blinks Bluetooth
symbol
· Rotating the Jog dial to select the desired channel between 1-22.
· If you press the PTT key to return to Communication mode · Rotating the Jog dial to select the desired channel between
1-38. · If No tone selects the 0 · If you press the PTT key to return to Communication mode · Rotating the Jog dial to select the desired vox level · If you press the PTT key to return to Communication mode · Rotating the Jog dial to select the voice call on or off. · If you press the PTT key to return to Communication mode
· Complete audio is output. · If you press the PTT key to return to Communication mode · Communication Mode to return to
double press Jog button
If you wish to mode selection, press the Jog button twice briefly. Pressing the Jog button shortly twice the current set mode is the audio output. You turn the Jog dial to select the desired mode.
ChatterBox
Page 7 of 15
Press
Setting
Jog dial mode
LCD Display
Description of mode
1 time 2 times 3 times 4 times
Communi cation Intercom m FM Radio
Music playing
Displays antenna bar
Blinks `I’
Displays `FM’
Displays
· Bike to bike communication · Rider to passenger communication · FM Radio Listening · Connection with the Bluetooth device
Multiple device modes
The X2-C can operate on four different device modes. The table shown below will briefly explain those device modes.
Device modes A Bike to Bike Group
Communicator
B Rider to passenger communicator
C Bluetooth transmitter with remote control
D FM Radio
Description
Bike to bike communication is the primary device mode for the X2-C user. It is also the default device mode when you turn the unit on. Unlimited number of riders can communicate as long as you are all on the same channel and talk group. With 22 channels and 38 talk groups for each channel, users can have 836 different possibilities of having their own communication path.
Rider to passenger communication is also possible by sharing the X2-C with a passenger headset. (Passenger headset and extension cord sold separately) When in Intercom mode the communication with your passenger is private. When NOT in intercom mode both you and your passenger can communicate with other bikes that are on the same channel. Your passenger can also listen to the same audio device and/or music.
The X2-C built in Bluetooth will allow you to wirelessly connect your Bluetooth Smartphone, MP3 player (w/ BTA/BTD Bluetooth adapter), Bluetooth ready GPS system, or Bluetooth cell phone.
* Depending on your device you can also remotely control your Bluetooth ready devices with the X2-C.
FM Radio allows you to listen to local radio stations automatically or manually.
3. Bike to bike communication
The X2-C can communicate with an unlimited number of riders. Before riding everyone must turn their units on and make sure they are on the same main channel and talk group. In order to transmit to other riders you must use the voice activation, handle bar mount PTT button, or the PTT on the unit. Once you talk, everyone on your channel will hear. However, only one person at a time can talk. It is a good idea to use the word “over” when done talking. This way others will know that they can now say something back. It is strongly suggested that you practice talking back and forth in your house before actually using on a ride. This way you can get a feel of what to expect.
Power On/Off: Press and hold the power button. You will notice that the LCD display will turn on. To power
the unit off, press and hold the power button until you hear the beep.
ChatterBox
Page 8 of 15
Set Volume level: There are two types of volume level control shown below:
Headset speaker volume: The volume is adjusted by turning left or right the Jog dial. Microphones volume: There is no volume control for microphones. System has a default volume level.
Choose a channel for the group: After briefly pressing the Jog button once to select the desired
channel. Press the Jog button briefly to have to choose between 1-38. Press the PTT key to return to the Communication mode, or after 5 seconds, it automatically returns to the Communication Mode. Make sure everyone in your group has set up same channel and talk group. Then you are ready to communicate.
Press Mode button 1 time
2 times
MODE selected: Main Channel
Talk Group
Description of mode
Short press Jog botton Rotating the Jog dial to select the desired channel between 1-22. Exit to the Communication mode, if you press the PTT key Short press Jog botton Rotating the Jog dial to select the desired channel between 1-38. If you choose to 0. There is no set Talk Group. Exit to the Communication mode, if you press the PTT key
Frequency table.
Channel
Frequency
Maximum Range
Channel
Frequency
Maximum Range
1
FRS
2 miles
12
FRS
2 miles
2
FRS
2 miles
13
FRS
2 miles
3
FRS
2 miles
14
FRS
2 miles
4
FRS
2 miles
15
FRS
2 miles
5
FRS
2 miles
16
FRS
2 miles
6
FRS
2 miles
17
FRS
2 miles
7
FRS
2 miles
18
FRS
2 miles
8
FRS
2 miles
19
FRS
2 miles
9
FRS
2 miles
20
FRS
2 miles
10
FRS
2 miles
21
FRS
2 miles
11
FRS
2 miles
22
FRS
2 miles
Channel 10 is an Emergency Channel. Use the emergency channel only for the purpose of soliciting or rendering assistance to a traveler. This channel is also used by certain organizations during emergency situations and may not necessarily be monitored. Use CTCSS subchannels for X2Slim-P to X2-C compatibility.
Side tone: When transmitting by using PTT or voice activation you will hear yourself in your own speakers.
This is called side tone. Side tone is what tells you that your microphone is working.
Using the voice activation feature(VOX): The voice activation feature is what allows you to
communicate to other riders without using the PTT. This feature can work very well but does need patience and understanding. In order to activate VOX feature, press and hold the Jog button until beeps two times and voice prompt says “VOX on”. To adjust the VOX sensitivity, place the unit into communication mode. Then short press until the voice prompts says “VOX”. Turn the Jog dial until the desired sensitivity is achieved. Setting 5 has the highest sensitivity. Setting 1 has the lowest sensitivity.
4. Rider to Passenger Communication
ChatterBox
Page 9 of 15
The X2-C does not require a separate unit for a passenger to communicate with the rider and others. In order to connect a passenger you must purchase an additional headset and extension cord. Please contact a dealer near you or call customer service.
Listening to bike to bike communication
When connected Passenger can communicate with other riders.
Rider and Passenger only communication
This unit allows a rider and passenger to communicate in private without the need of an additional unit. You will need to purchase an additional pair of Chatterbox Universal Headsets and the Chatterbox extension cable. In order to activate this feature, double press the Jog button, turn the Jog dial clockwise, and press the Jog button to lock in this mode. This should open an open connection between rider and passenger for communication.
5. Bluetooth feature with audio control
The X2-C is equipped with Bluetooth transmitter that allows you to pair up to 2 Bluetooth devices simultaneously. You must understand that NOT just ANY 2 Bluetooth devices will always work. When pairing two devices, Bluetooth only permits 1 hands free device and 1 audio device. You cannot pair 2 audio devices and you cannot pair 2 hands free devices. It will only allow 1 of each kind. An example of a hands free device is a cell phone. An example of an audio device is an iPOD/MP3 player with a Bluetooth* adapter. Please note some Smart phone’s (iPhone and Android phones) take up BOTH devices when paired to the X2-C. This is why you will be able to listen to music and answer the phone from a smart phone. These phones do not have an option to disable this. Some motorcycle specific GPS devices also take up both devices when paired. This is why you can listen to music, hear your voice prompted directions, and answer your phone through them.
* You will find a chart below that explains the different combinations of accessories and what will work.
Bluetooth feature: The Bluetooth feature will allow you to listen to the music, GPS direction, and/or
answer phone calls wirelessly.
Pairing: In order to pair the X2Slim to a Bluetooth device you must follow the directions below. Please make
sure that the device you are trying to pair is Bluetooth capable.
1
Make sure the X2-C is in the OFF position and the device you want to pair is near. Please note
that you must make sure any other Bluetooth devices in the area are turned off.
2
1) If you want to connect with a Bluetooth device and the connection never previously connected,
press the Power key while pressing the Jog button together for 3 seconds at power on. “Bluetooth
pairing” the voice prompt is output and X2Slim blinks the green light on LCD
2) The connection to the Bluetooth devices that were previously connected to automatically
connect when the power is turned on.
( if X2-C is not connected using method 2), you try to do method 1).)
3) If you wish to connect with Wireless PTT, you have to put the X2 PTT status to the pairing mode
in the first place and press and hold the power key while pressing the PTT key the X2 for three
seconds at power on.
3
Follow the “pairing” instructions for your Bluetooth device. Please allow about 30 seconds for
your device to search X2-C. If done correctly, you will notice the name “X2-C” on your devices
Bluetooth list.
4
Press and hold the UP button for 3 seconds until the LCD display shows “Bt on”. You will notice
that the X2-C(X2) will now connect with your device. (If you find X2-C, click “X2-C ” in the device
screen shown at the Bluetooth device. The “Bluetooth connected” voice output in X2 and the
Bluetooth mark is displayed on the LCD screen at X2-C
Pairing multiple devices: you can pair any Bluetooth enabled MP3 player, Mobile phone, and Navigation
system with X2-C. However, only two devices can be paired with X2-C simultaneously. Table shown below summarizes the way you can pair multiple devices simultaneously.
There are two ways you can get all three, music, navigation, and phone simultaneously.
ChatterBox
Page 10 of 15
The first way is by using a navigation system that supports pairing with mobile phone. This does NOT mean that any navigation system with Bluetooth will work. These types of Navigation systems are usually the motorcycle specific models. (Garmin Zumo and Tom Tom Rider models) In this case, you need to pair your mobile phone to the Navigation system first then pair the navigation system and MP3 player to the X2-C.
The second way is to buy one of the navigation apps for you Smartphone that supports In-app music player. With this route you can do the following all from your Smartphone; hear your voice prompted directions, answer/make phone calls, and listen to music from the Mp3 player. We highly recommend this setting.
Bluetooth enabled devices
Smart Mobile phone phone
MP3 player
Navigat ion
Music Navig ation
phone
Ways to pair two devices 1
Yes
Yes
2
Yes
Yes
3
Yes Yes
Way to pair three devices 4
Yes
Yes
*Yes
*Navigation systems that supports pairing with phone: TomTom rider2, Zumo550
Smart way to get music, navigation, and phone simultaneously by pairing one device
5
Yes Yes* Yes
*You need to buy GPS
apps for your
Smartphone that
supports In-App Music
player (Gokivo, TomTom)
Using Smartphone to get music, phone, and navigation; Once you have paired your Smartphone
with X2-C, you may listen to your music from your Smartphone using your own playlist. When there’s an incoming phone call, you will hear your music faded away and get paused and start hearing engine revving sound. You simply short press Jog button on X2-C to answer. If you want to end the call, just short press Jog button again. As soon as you end the call, the music will play back automatically.
If you want to use navigation system, you need to buy one of the navigation apps offered for your Smartphone. Please make sure you get the In-App music player for more streamlined operation. Unlike the navigation systems that rely on network to get the maps and information, there are systems that you still can use even during the absence of network by accessing the maps and information already downloaded in your Smartphone. If you phone has enough disk space, this option is the most suitable for the motorcycle riders.
*For longer ride, you need to have charger for your Smart phones if you want to use navigation system.
ChatterBox
Page 11 of 15
Remote control: The X2-C Bluetooth feature can also remotely control the devices so that you don’t have
to reach for your device in your pocket dangerously while you are riding. The Table below will show you the remote control functions available. (Does not apply to all devices)
Music GPS Cell
Buttons to use (Only in Bluetooth* mode)
phone
Pause and Play
Yes
Short Press Jog button
Skip track
Yes
Rotate the Jog dial to the right in pressing Jog
button
Reverse track
Yes
Rotate the Jog dial to the left in pressing Jog
button
Volume UP & DOWN Yes
Yes Yes
Rotate the Jog dial to the left(down) or right(up)
Answer incoming call
Yes
Short Press Jog button
End incoming call
Yes
Short Press Jog button
(*Long press: Hold the button for 2 seconds, Short press: hold the button for half second)
You must be in Music Play mode for music playback.
6. FM Radio
The X2-C has a built in FM radio player. The following will explain how to use the FM radio feature.
Turn on/off the FM Radio: After the X2-C is on,
1. Go to the mode change state twice briefly pressing the Jog button 2. Within 3 seconds, turn the Jog dial to select the FM Radio mode. 3. FM Radio is automatically Turn On 4. when you want to turn off FM Radio you go to the mode change state twice briefly pressing the Jog button and rotate Jog dial to select another state.
Change volume: While listening to the radio, Rotate the Jog dial to the left(down) or right(up) to adjust the
volume.
Search FM radio stations
1. If you want to choose FM radio stations automatically After short press Jog dial, you rotate Jog dial left or right to select FM Radio Station. 2. If you want to choose FM radio stations manually Based on the currently selected FM radio stations while press Jog button you turn the Jog dial right up 100Khz unit, turn the Jog dial to the left down 100Khz basis. Select the desired FM Radio Station.
7. Putting it all together
Typical setting: The most typical setting for X2-C is listening to your music, hearing voice prompted
direction from your navigation system, and answering incoming calls while you communicate with your fellow riders and/or passenger.
1
Turn on X2-C procedure
1) If you want to connect with a Bluetooth device and the connection never previously
connected, press the Power key while pressing the Jog button together for 3 seconds.
“Bluetooth pairing” the voice prompt is output and X2-C blinks the green light on LCD
2) The connection to the Bluetooth devices that were previously connected to
automatically connect when the power is turned on.
(if X2-C is not connected using method 2), you try to do method 1) for connection.)
3) If you wish to connect with Wireless PTT, you have to put the X2-C PTT status to
the pairing mode in the first place and press and hold the power key while press the
PTT key in the X2-C for three seconds.
2
Choose and set the channel and talk group. Test with PTT button or Voice activation
to see if everyone can hear each other.
ChatterBox
Page 12 of 15
3
Pair your Smartphone with Navigation app to the X2-C.
4
After X2-C is putted the Music Play mode you access navigation system in your
Smartphone and initiate the navigation by inputting destination. Afterwards start your
mp3 player.
5
Now you should hear your music and hear the turn by turn direction from your
navigation system occasionally. You are also ready to answer your phone calls by
short pressing the Jog button. Lastly you can communicate with your fellow riders who
are on the same channel.
Priority: Table shown below summarizes the priority among different devices. When you are in the
Bluetooth* device mode, the navigation direction and phone calls get priority over the music. This means that when a phone call is answered the music will be paused. As soon as the call ends, the music will play again. Same thing applies with fellow rider communication. When you hear communication the music will pause. After the communication is finished the music will automatically come back.
Priority Bluetooth FM Radio
1 Cell phone Cell phone
2
Rider communication Rider communication
3 Navigation FM Radio
4 MP3
Summary of button functions: The table below will summarize the button functions that have been
explained in this manual
ChatterBox
Page 13 of 15
To Activate To deactivate
Rider communication (Default setting)
Press power on/off button
Press power on/off button
Volume up Volume down To talk
To Answer phone call To skip music track
Rotate the Jog dial to the right Rotate the Jog dial to the left
Press and hold PTT or Use voice activation Short press Jog button
To reverse music track
To pause and play To skip radio station
To reverse radio station
To select radio station manually
Rider to Passenger communication (private) Select Intercom mode
Press twice briefly to Jog dial and choose a different mode Rotate the Jog dial to the right Rotate the Jog dial to the left
Bluetooth feature
Press the power button while pressing the Jog button
Rotate the Jog dial to the right Rotate the Jog dial to the left
FM Radio
Select FM Radio mode
Press twice briefly to Jog dial and choose a different mode Rotate the Jog dial to the right Rotate the Jog dial to the left
Short press Jog button
Short press Jog button Rotate the Jog dial to the right While press the Jog button
Rotate the Jog dial to the left While press the Jog button Short press Jog button
Short press Jog button
Short press Jog button and turn Jog dial to the right Short press Jog button and turn Jog dial to the left Turn the Jog dial left or right while pressing Jog button
Technical Specification
GENERAL
ChatterBox
Page 14 of 15
Frequency range Modulation type Channel capacity Channel spacing Power supply pack Current drain transmitter Battery life Operating temperature Dimensions Weight TRANSMITTER
From 462.550 MHz to 467.7125 MHz 8K50F3E 22 Channels 12.5KHz DC 3.7 V; Li-ion rechargeable (1W); <1000mA 8 hours talk time, 20 hours of stand by time -20C + 60C 82(H) x 130 (W) x 37 (D) mm 3.2 oz. (with battery)
Frequency stability Hum & Noise Spurious & Harmonics Audio distortion RECEIVER Sensitivity (12dB SINAD) Selectivity Inter-Modulation Spurious and image Maximum audio output Audio distortion Hum & Noise
Better than +/- 5ppm within -40dBc (with 300Hz to 3KHz audio filter) -60dBc less than 5% (1KHz tone 60% modulation)
0.2uV (-119dBm SINAD) -60dB -60dB -60dB rejection more than 100mW less than 5% -40dBc (with 300Hz to 3KHz audio filter)
ChatterBox
Page 15 of 15
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Specific Absorption Rate (SAR) information: This device meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is 1.6 W/ kg averaged over one gram of tissue. Device types: This device has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the This device kept 0mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain an 0mm separation distance between the user’s body and the back of This device. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.
·
DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may
also cause you to exceed RF exposure limits. A proper antenna is the antenna supplied with this radio by the
manufacturer or an antenna specifically authorized by the manufacturer for use with this radio, and the antenna
gain shall not exceed the specified gain by the manufacturer declared.
·
DO NOT transmit for more than 50% of total radio use time, more than 50% of the time can cause
RF exposure compliance requirements to be exceeded.
·
During transmissions, your radio generates RF energy that can possibly cause interference with other
devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so.
·
DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as
hospitals, aircraft, and blasting sites.
·
Portable Device, this transmitter may operate with the antenna(s) documented in this filing in Push-
to-Talk and body-worn configurations. RF exposure compliance is limited
to the specific belt-clip and accessory configurations as documented in this filing and the separation distance
between user and the device or its antenna shall be at least 2.5 cm.Highest Reported SAR XXX W/Kg for Front of
face,Highest Reported SAR XXX W/Kg for Body worn.
General population/uncontrolled Radio, this radio is designed for and classified as “General population/un-
controlled Use”.
Documents / Resources
 |
UNiMO X2-C ChatterBox 24P Long Range Communicator [pdf] Owner's Manual X2-C, X2-C ChatterBox 24P Long Range Communicator, ChatterBox 24P Long Range Communicator, 24P Long Range Communicator, Communicator |