Latch7 Z-Wave Smart Lock
“
Specifications
Structural Characteristics
| Parameter | Value |
|---|---|
| Product Identifier | LATCH7-ZWAVE BLACK |
| Color | Indoor & Outdoor |
| Operating Temperature | – |
| Relative Humidity | 30%-95% Non-condensing |
| Product ID | 0x0003 |
| Product Type ID | 0x0004 |
Hardware Characteristics
| Parameter | Value |
|---|---|
| Z-Wave Model | – |
| Indicator Light Color | GREEN/BLUE/RED |
| Battery Info | AA alkaline battery x4 |
Software Characteristics
| Parameter | Value |
|---|---|
| Wireless Technology | Z-Wave |
| Certification Type | Z-Wave Plus v2 |
Product Usage Instructions
Product Quick Start
Z-Wave DSK Location
- You can find the QR code on the battery cover of your door
lock. - You may also find the DSK in the user manual of each
product.
How to add the product into Z-Wave network
- Follow the user guide of the hub to enter inclusion mode.
How to remove the product from the Z-Wave network
- Follow the user guide of the hub to enter exclusion mode.
How to factory reset
Please use this procedure only when the network’s primary
controller is missing or inoperable. Use a Reset Needle to push the
Reset Button located inside the battery compartment for around 10
seconds until you hear one long beep and two short beeps.
How to use the Lock
- Enter a 4-8 digit code and press ULTRALOQ Button to
unlock.
Frequently Asked Questions (FAQ)
Q: How can I change the user code?
A: Once the device is added to the Z-Wave network, the user code
can only be changed via Z-Wave commands.
Q: Where can I find the default code?
A: The default code is 3494.
“`
ULTRALOQLatch7Z-Wave®SmartLock
1. Overview
ThisdeviceisasecurityenabledZ-WavePlus®v2productthatisabletouseencryptedZ-Wave Plusv2messagestocommunicatetoothersecurityS2enabledZ-WavePlusv2products.This devicemustbeusedinconjunctionwithaS2securityenabledZ-Wavecontrollerinordertofully utilizeallimplementedfunctions.Otherwiseitwillautomaticallyturnintoalowerlevelof securitytomaintainbackwardcompatibility.ThisproductcanbeoperatedinanyZ-Wave networkwithotherZ-Wavecertifieddevicesfromothermanufacturers.Allmainsoperated nodeswithinthenetworkwillactasrepeatersregardlessofvendortoincreasereliabilityofthe network.SmartStartenabledproductscanbeaddedintoaZ-WavenetworkbyscanningtheZWaveQRCodepresentontheproductwithacontrollerprovidingSmartStartinclusion.No furtheractionisrequiredandtheSmartStartproductwillbeaddedautomaticallywithin10 minutesofbeingswitchedoninthenetworkvicinity.
2. Interfaces
Terminology
Keypad Thumbturn QRCode
Description
Usedtooperatevariousfunctionsofthedoorlock
Formanuallock/unlockoperation
2Dbarcodeformatthatcancontainlargeamountsofinformationinasmall squareofencodedblocksresemblingarandomcheckerboardpattern.InZWave,itisusedtorepresenttheS2publicpartoftheDSKonadevice,aswell asadditionalinformationneededfortheinclusionprocess
3. Specifications
3.1StructuralCharacteristics
Parameter
ProductIdentifier Color
Value
LATCH7-ZWAVE BLACK
Usage
Indoor&Outdoor
OperatingTemperature
ExternalAssembly:-4°F~149°F(-20°C~65°C) InternalAssembly:14°F~131°F(-10°C~55°C)
RelativeHumidity
30%-95%Noncondensing
ProductID
0x0003
ProductTypeID:
0x0004
3.2HardwareCharacteristics
Parameter
Z-WaveModel IndicatoeLightColor BatteryInfo
Value
EFR32ZG28A GREEN/BLUE/RED AAalkalinebatteryx4
3.3SoftwareCharacteristics
Parameter
WirelessTechnology CertificationType Z-WaveSDKVersion Z-WaveLibraryType Z-WaveRoleType GenericDeviceType SpecificDeviceType SecurityClass SmartStart
OverTheAir OTA
Value
Z-Wave Z-WavePlusv2 7.23.0 EnhancedEndNode232 ListeningSleepingEndNodeRoleType GENERIC_TYPE_ENTRY_CONTROL(0x40) SPECIFIC_TYPE_DOOR_LOCK(0x01) S0,S2
‘ Support.Afterpoweringon,SmartStartisautoactiveifit soutoftheZ-
Wavenetwork. Support.FirmwarecanbeupdatedviaRF.
MultichannelDevice Association FactoryReset Power-downMemory UsercodeReport
No Support.RefertoSectionAssociationCommandClasses. Support.RefertoSectionHowtofactoryreset. Support.Allcommandsettingswillstayunchangedevenpowerdown. Support.Whenusercodechanges,sendoutnotificationviaGroup1.
4. ProductQuickStart
4.1Z-WaveDSKLocation
1. YoucanfindtheQRcodeonthebatterycoverofyourdoorlock. 2. YoumayalsofindtheDSKintheusermanualofeachproduct.
Note:Pleasedonotremoveordamagethem.
4.2HowtoaddtheproductintoZ-Wavenetwork
1. Followtheuserguideofhubtoenterinclusionmode. 2. OperateonlockEnter”Includemode”:Holdthe”Enter”buttonfor3seconds,hear2beeps
andflashingbluelight,internalLEDFlashingGreenlight.Thelocknowenterssetupmode.
4.2.2.1EnterButton 3. Followtheprompts,scantheQRcodelocatedonthebettercover,orenterthe5-digitPIN
code. Note:Pleasecompletethepreparationwithin30seconds.Ifyoumiss,pleasepressthe ULTRALOQbuttonagaintoenter.
4.3HowtoremovetheproductfromtheZ-Wavenetwork
1. Followtheuserguideofhubtoenterexclusionmode. 2. OperateonlockEnter”Exclusionmode”:Holdthe”Enter”buttonfor3seconds,hear2beeps
andflashingbluelight,internalLEDFlashingGreenlight.
3. Removefromthehub.
4.3.2.1EnterButton
4.4Howtofactoryreset
‘ Pleaseusethisprocedureonlywhenthenetwork sprimarycontrollerismissingorotherwise
inoperable. PleaseuseaResetNeedletopushtheResetButton(ocatedinsidethebatterycompartment)for around10secondsuntilyouhearonelongbeepandtwoshortbeeps.
4.4HowtousetheLock
1. Enter4-8digitcodeandpressULTRALOQButtontounlock. Note:Thedefaultcodeis3494.OncethedeviceisaddedtotheZ-Wavenetwork,theuser codecanonlybechangedviaZ-Wavecommands.
2. Useyoursmarthomesystemtounlock.Refertoyoursmarthomesysteminstructionsfor moreinformation.
5. SupportedCommandClasses
CommandClass
Versio n
Not added
Nonsec ur added
Securely0added
Nonsecu reCC
Secure CC
Securely2added
Nonsecu reCC
Secure CC
CommandClass
2
Association
Support
Support
CommandClass
3
AssociationGroupInfo
Support
Support
CommandClassBasic
2
Support
Support
CommandClass
1
Battery
Support
Support
CommandClassDevice
3
ResetLocally
Support
Support
MultiChannel
3
Association
Support
Support
CommandClassDoor
4
Lock
Support
Support
CommandClass
5
FirmwareUpdateMeta
Data
Support
Support
CommandClass
3
Indicator
CommandClass
2
ManufacturerSpecific
CommandClass
1
Powerlevel
CommandClass
1
Security0
CommandClass
1
Security2
CommandClass
1
Supervision
CommandClass
2
TransportService
CommandClassUser
4
Code
CommandClass
2
Version
CommandClassZ-
2
WavePlusInfo
Support Support
Support Support
Support
Support
Suppo rt
Support
Support
Support
Suppo rt
Support
Support
Support
Suppo rt
Support
Support
Support
Suppo rt
Support
Support
Support
Support
Support
Support
Support
Suppo rt
Support
Support
Support
6. AssociationCommandClasses
GroupID
Maximu mNodes
Descripti on
Function
1
5
Lifeline
DEVICE_RESET_LOCALLY_NOTIFICATION DOOR_LOCK_OPERATION_REPORT BATTERY_REPORT INDICATOR_REPORT NOTIFICATION_REPORT
DOOR_LOCK_CONFIGURATION_REPORT USER_CODE_REPORT
7. BasicCommandClasses
Command Class
Value
Mapped
Value
Function
BasicSet
0x00 0xFF
DoorLockOperationSet
DoorUnsecured
Openthedoor
DoorSecured
Closethedoor
BasicReport
0x00 0xFF
DoorLockOperation Report
DoorUnsecured
Thelockisopened
DoorSecured
Thelockisclosed
BasicGet
DoorLockOperationGet
8. NotificationCommandClasses
Notificatio nType
Event
AlarmReports
0x06
0x01
ManualLock
0x06
0x02
ManualUnlock
0x06
0x03
RFOperateLock
0x06
0x04
RFOperateUnlock
0x06
0x05
KeypadLock
0x06
0x06
KeypadUnlock
0x06
0x09
AutoLockOperateLocked
0x06
0x0B
Lockjammed
Description
Manuallockoperation Manualunlockoperation RFlockoperation RFunlockoperation Keypadlockoperation Keypadunlockoperation Autolocklockedoperation Lockjammed
0x06 0x06 0x06 0x06
0x0C
AllUserDeleted
0x0D
UserDeleted
0x0E
UserAdded
0x0F
DuplicatePin-codeerror
Allusercodesdeleted Singleusercodedeleted Newusercodeadded Newusercodenotaddedduetoduplicate code
0x06
0x10
TamperAlarm
Keypadtemporarydisabled
8.1 HowtoTriggerNotifications
Event
AlarmReports
TriggerMethod
0x01
ManualLock
RotatethumbturntoLocked
0x02
ManualUnlock
RotatethumbturntoUnlock
0x03
RFOperateLock
RFlockoperation
0x04
RFOperateUnlock
RFunlockoperation
0x05
KeypadLock
Lockedvia”ULTRALOQ”button
0x06
KeypadUnlock
Unlockbyenteringusercodeviakeyboard.
0x09
AutoLockOperate Locked
Unlockfirst,andafterwaitingfor30seconds,thedevicewillAuto Lock.
0x0B
Lockjammed
Intheunlockedstate,presstheUltraloqrelockbuttonandmanually holdthethumbturntopreventitfromrotating(simulatingajam). Onceyouheartwobeeps,thejamhasbeentriggered.Atthispoint,a notificationcanbereceived.
0x0C
AllUserDeleted
Deleteallusercodes
0x0D
UserDeleted
Deletesingleusercode
0x0E
UserAdded
Newusercodeadded
0x0F
DuplicatePin-code error
Newusercodenotaddedduetoduplicatecode
0x10
TamperAlarm
Thepasswordisenteredincorrectly5consecutivetimes
9. IdentityFunction
IndicatorID NodeIdentify
0x50
PropertyID OnOffPeriod OnOffCycles OntimewithinanOn/Offperiod
0x03 0x04 0x05
Documents / Resources
 |
ULTRALOQ Latch7 Z-Wave Smart Lock [pdf] Instruction Manual Latch7 Z-Wave Smart Lock, Z-Wave Smart Lock, Smart Lock, Lock |