MS1 Motion Sensor
Instructions Manual
Introduction
- Package List: Motion Sensor MS1 /MS1P VI) Micro USB cable (.1) Screw (.2) User Guide (.1) Pluggable Terminal Block Connector (MS1P) (k1)
- Product Function: monitor the movement of people or animals and measure the environment’s temperature and humidity.
Technical Specifications
Product: UbiBot Motion Sensor MS1 /MS1P
Detection distance: 12 meters
Detection angle: vertical 40 degrees, horizontal 105 degrees
Power supply: Micro USB/POE power supply ./AC power supply*
Operating temperature M51: -10 °C to 50 Non-condensing
Operating humidity MS1: 59096 RH, Non-condensing
Operating temperature MS1P: 0 °C to 50 °C
Operating humidity MS1 P: 57096 RH
Operation system: Android/i0S
Network: 2.4GHz WiFi/Rj45 Ethernet*
Wireless standard: IEEE 802.11 b/g/n
POE Standard: IEEE 802.3-2005 *
Bluetooth: BT4.2, Classic BT&BLE
*Text marked with an asterisk means the feature depends on the specific model purchased
Detection Range
Our product uses the pyroelectric infrared sensor, which is featured with a detection distance of up to 12 meters, 40 degrees in the vertical direction, and 105 degrees in the horizontal direction.
Indicator Status & Operations
Power on and off: The device will switch on automatically when power is supplied and shut down automatically when power is off.
When the indicator flashes green, it means there is movement detected.
When no movement is detected, the indicator goes off.
When the indicator flashes alternately red and blue, it means the device is in the setup mode.
When the indicator is constantly blue, the device is reset to default settings.
When the indicator is constantly red, it means there are network errors.
When the indicator flashes red, it means there are hardware errors.
Press and hold the button for 5 seconds to enter the setup mode.
Under “setup mode”, press the button three times in quick succession to reset the device.
Power Supply
- Power supply: Micro USB (5 V, 2 A)
POE power supply* (7 W)
AC power supply* (110 V-240 V ac, 50/60 Hz)
* Text marked with an asterisk means the feature depends on the specific model purchased.
APP Installation
Option 1:
Download the App from www.ubibot.com/setup
Option 2:
Search for “UbiBot” on the App Store or Google Play.
Network Setup
STEP 1.
Launch the App, register if needed, and log in. Tap “+” to add a device. Scan the QR code on the device or manually enter the serial number.
STEP 2.
Enter the WiFi setup mode: In the ON state, press and hold the button for 5 seconds until the indicator flashes alternately red and blue.
STEP 3.
Turn on your phone’s Bluetooth first. According to the prompt in the APP, fill in the current WiFi password and tap “Next Step”. After the progress bar is completed, the setup finishes.
If the setup fails, make sure that the indicator flashes alternately red and blue. Make sure that the WiFi is 2.4GHz and the password is entered correctly.
Device Installation
This product is a wall-mounted type, and the best performance can be achieved when the deployment position is 2 to 2.2 meters high, measured from the floor.
Notes
For better monitoring results, please pay attention to the following when deploying the device:
- Do not face glass doors and windows;
- Avoid facing large objects that are prone to swinging, such as trees and tall shrubs;
- Should not be opposed to any hot or cold vents or sources;
- Keep away from air conditioners, refrigerators, stoves, and all places where air temperature can easily fluctuate.
Warranty Information
This device is warranted to be free of defects in materials and workmanship for a period of up to one year from the original purchase date.
The following situations are not covered by the warranty:
- Issues arise after the warranty period has ended.
- Malfunction or damage caused by improper handling or not operating the device according to the instructions.
- Damage occurs from operating devices outside the recommended temperature and humidity range, damage from contact with water, and damage from applying excessive force to the device or any cables and connectors.
- Natural wear and aging of materials.
- Failure or damage caused by unauthorized removal of the product.
- Failure or damage caused by force majeure.
- Other faults or damage not caused by product design, technology, manufacturing, quality, etc.
Documents / Resources
 |
UBIBOT MS1 Motion Sensor [pdf] Instructions MS1, Motion Sensor, MS1 Motion Sensor |
