U-PROX PIR Combi Wireless Motion and Breakglass Detector
“
Product Information
Specifications
- Power Supply: 3V, CR123A lithium battery
(pre-installed); battery service life up to 5 years - Wireless Communication:
- ISM-band interface with multiple channels using secure two-way
communication (256-bit encryption and sabotage detection) - ITU Region 1 (EU, UA): 868.0 to 868.6MHz, 100kHz bandwidth, 20
mW max, up to 4800m (line-of-sight) - ITU Region 3 (AU): 916.5 to 917MHz, 100kHz bandwidth, 20 mW
max, up to 4800m (line-of-sight)
- ISM-band interface with multiple channels using secure two-way
- Dimensions & Weight:
- Device: 90 x 60 x 34.35mm; Weight: 150 grams
- With an angle bracket: 90 x 60 x 41.6mm
- With a wall bracket: 90 x 60 x 48.84mm
Product Usage Instructions
Installation Instructions
7.1 Selecting the Installation Location
Choose a suitable location for mounting the device ensuring
optimal coverage of the area.
7.2 Mounting Procedures (Wall and Angle Bracket Options)
Follow the provided instructions for mounting the device using
either the wall bracket or the angle bracket.
Operation and Settings
8.1 Device Registration
Register the device with the U-PROX control panel following the
provided guidelines.
8.2 Alarm Indication and Communication Test
Test the alarm indication and communication by triggering the
sensor as per the user manual.
8.3 Configuring Settings
Adjust and configure the settings using the U-PROX Installer
Mobile Application or the Installer Web Portal.
Maintenance and Service
Regularly check the device for proper functioning and ensure
timely maintenance as required.
Compliance and Warranty
Refer to the user manual for compliance standards and warranty
information related to the product.
FAQ
Q: Can the U-PROX PIR Combi be used outdoors?
A: No, this sensor is intended for indoor use only. Using it
outdoors may lead to inaccurate readings or damage.
Q: How do I replace the battery?
A: To replace the battery, follow the instructions provided in
the user manual carefully to avoid any safety hazards.
“`
U-PROX PIR Combi User Manual
Wireless Motion and Breakglass Detector with Pet Immunity
Table of Contents
Introduction Safety Warnings Applications for Customization Description and Principle of Operation Functional Elements Technical Specifications Installation Instructions
7.1 Selecting the Installation Location 7.2 Mounting Procedures (Wall and Angle Bracket Options) Operation and Settings 8.1 Device Registration 8.2 Alarm Indication and Communication Test 8.3 Configuring Settings Maintenance and Service Compliance and Warranty Scope of Delivery
1. Introduction
The U-PROX PIR Combi is a combined wireless motion detector and acoustic breakglass sensor designed for indoor residential or industrial premises. Equipped with a PIR sensor and a microphone, it detects changes in the thermal balance or the sound of breaking glass. When triggered, the device sends an alarm notification securely to the U-PROX control panel. This sensor is intended for indoor use only.
For technical support, please call +38(091)481-01-69 or email
support@u-prox.systems
2. Safety Warnings
Battery Safety:
This device is powered by a built-in 3V CR123A lithium battery. Replacing the battery with an incorrect type can lead to fire or explosion. Always dispose of used batteries in accordance with local regulations.
Installation Precautions:
Install the device only when the power is off and follow all electrical and fire safety guidelines. Do not disassemble the device or its power supply while energized.
Handling:
Avoid exposing the sensor to extreme conditions or using non-approved accessories.
3. Applications for Customization
The U-PROX PIR Combi is designed to integrate seamlessly with the U-PROX security system. Customize its settings and monitor its performance using:
U-PROX Installer Mobile Application: Use your mobile device to perform setup, testing, calibration, and configuration of the sensor. Installer Web Portal: Access the web portal at
for comprehensive configuration and remote monitoring.
4. Description and Principle of Operation
The U-PROX PIR Combi is a dual-function sensor that combines a motion detector and a breakglass detector. It continuously monitors the area for two types of events:
Motion Detection: Using a passive infrared (PIR) sensor, it detects human movement while remaining insensitive to animals up to 20kg. Breakglass Detection: The built-in microphone and Fresnel lens detect the sound of glass breaking. The sensor monitors glass dimensions ranging from 0.5m x 0.5m to 3.0m x 3.0m with a detection angle of 120° and a glass thickness of 28mm. When an event is detected–either motion or glass breakage–the sensor sends an encrypted alarm notification via an ISM-band wireless interface to the U-PROX control panel.
5. Functional Elements
1. Device Case 2. Microphone Hole 3. Light Indicator for Operating Modes 4. Fresnel Lens (for both PIR and
acoustic detection) 5. Mounting Bracket (available as a wall
bracket or an angle bracket) 6. Tamper (Sabotage) Switch 7. Back of the Device 8. On/Off Switch/Button
6. Technical Specifications
Power Supply: 3V, CR123A lithium battery (pre-installed); battery service life up to 5 years
Wireless Communication:
ISM-band interface with multiple channels using secure two-way communication (256-bit encryption and sabotage detection) ITU Region 1 (EU, UA): 868.0 to 868.6MHz, 100kHz bandwidth, 20 mW max, up to 4800m (line-of-sight) ITU Region 3 (AU): 916.5 to 917MHz, 100kHz bandwidth, 20 mW max, up to 4800m (line-of-sight)
Operating Temperature: 10°C to +55°C
Dimensions & Weight:
Device: 90 x 60 x 34.35mm; Weight: 150grams Bracket Options:
With an angle bracket: 90 x 60 x 41.6mm With a wall bracket: 90 x 60 x 48.84mm
Breakglass Detection:
Glass Dimension Range: 0.5m x 0.5m to 3.0m x 3.0m Detection Angle: 120°
Glass Thickness: 2mm to 8mm
Motion Detection:
Maximum Working Distance: 8m Target Detection Speed: 0.3 to 3m/s Optical Noise Immunity: >6500Lux
Additional Parameters:
Pet Immunity: Up to 20kg Detection Angle for Glass: 88° Environmental Conditions: Permissible humidity up to 75%; Environmental class II (EN 50131-1) Security Grade: 2
7. Installation Instructions
7.1 Selecting the Installation Location
Suitable Locations: Install indoors in areas where the sensor’s field of view will cover the most likely points of intrusion (e.g., near windows or glass doors).
Avoid:
Areas with direct sunlight or rapid temperature changes Rooms with high levels of radio interference Locations near objects that may block or attenuate the signal Areas where the sensor is exposed to excessive humidity or extreme temperatures
Tip: Use the U-PROX Installer app to perform a range test for optimal placement.
7.2 Mounting Procedures
Option A Wall Bracket Installation:
Prepare the Surface: Ensure the wall is clean, dry, and flat. Mount the Bracket: Secure the wall bracket using the screws and dowels provided in the mounting kit. Install the Sensor: Place the sensor onto the bracket and slide it down until the tamper switch locks. A confirmation light on the indicator will show that the sensor is properly installed.
Option B Angle Bracket Installation:
Prepare the Surface: Verify the surface suitability as with wall installation. Attach the Angle Bracket: Fix the angle bracket securely with the provided hardware. Position the Sensor: Insert the sensor into the bracket ensuring proper alignment and that the tamper switch is engaged.
7.3 Connecting External Components
If additional external components (such as an LED for visual arm/disarm confirmation) are required, connect them to the dedicated contacts as follows:
LD Contact: + LED (red) GND Contact: Ground (blue) DC Contact: Sensor (yellow)
8. Operation and Settings
8.1 Device Registration
Launch the U-PROX Installer Mobile App or Web Portal and log in with your installer credentials.
Add the Device: Follow the on-screen instructions to register the U-PROX PIR Combi with the U-PROX control panel. For best results, hold the sensor within approximately 1 meter of the control panel during registration.
8.2 Alarm Indication and Communication Test
Indicator Feedback: The sensor’s light indicator will display the operating mode. During a range test, the LED may flash different colors to indicate the quality of the signal:
Green: Excellent signal (up to 87 dBm) Yellow: Average signal (88 to 94 dBm) Red: Poor signal (95 to 111 dBm)
Alarm Notification: When motion or glass breakage is detected, the sensor sends an encrypted alarm notification to the U-PROX control panel.
8.3 Configuring Settings
Light Indication: Toggle the LED indicator on/off according to your requirements. Group Assignment: Assign the sensor to the appropriate security group (for example, “Front Door” or “Living Room Window”) to enable integrated system monitoring. Additional Settings: Further settings may be configured via the U-PROX Installer app or web portal to customize behavior, such as alarm delays and response to tampering.
9. Maintenance and Service
Cleaning:
Wipe the device periodically with a soft, dry cloth to remove dust and debris.
Battery Replacement:
If the battery’s service life ends (up to 5 years), replace the CR123A battery only with the approved type. Follow manufacturer guidelines and dispose of used batteries in compliance with local regulations.
Troubleshooting:
If the sensor does not communicate correctly, verify the installation, check for interference, and consult the diagnostics available in the U-PROX Installer app.
10. Compliance and Warranty
Standards Compliance:
The U-PROX PIR Combi complies with the Radio Equipment Directive 2014/53/EU and the Directive 2011/65/EU (RoHS). The original Declaration of Conformity is available on the U-PROX website in the Certificates section.
Warranty:
Warranty for U-PROX devices (excluding batteries) is valid for two years from the purchase date. If issues arise, please contact
support@u-prox.systems
–remote troubleshooting may be available.
11. Scope of Delivery
The complete package includes:
U-PROX PIR Combi Sensor CR123A Battery (Pre-installed) Wall Bracket Angle Bracket Mounting Kit Quick Start Guide
© 2024 Limited Liability Company Integrated Technical Vision www.u-prox.systems
Documents / Resources
 |
U-PROX U-PROX PIR Combi Wireless Motion and Breakglass Detector [pdf] User Manual U-PROX PIR Combi Wireless Motion and Breakglass Detector, U-PROX PIR, Combi Wireless Motion and Breakglass Detector, Wireless Motion and Breakglass Detector, Motion and Breakglass Detector, Breakglass Detector, Detector |