TYGER TG-LX3D82468 LanderX Triangular Drop

Specifications

• Brand: TYGER
• Model: LanderX TG-LX3D82468
• Material: Steel
• Finish: Black powder coat
• Weight Capacity: 300 lbs

Product Usage Instructions

Before Installation

1. Read the instructions carefully before starting the installation.
2. Remove contents from the box and verify all parts are present.
3. If missing parts or any damage is found, take a picture for claim purposes.
4. Visit www.tygerauto.com/contact to file a claim.

Torque Values

Fastener Size	Class 8.8 Torque (ft-lbs)	Class 10.9 Torque (ft-lbs)
6mm	6-7	6-7
8mm	15-16	22-23
10mm	31-32	44-45
12mm	54-55	78-79
14mm	87-88	125-126

Installation Steps

Step 1:

• Start the installation on the passenger/right side of the vehicle. Locate the front 3 factory studs along the inner sidewall of the body panel.

Step 2:

• Select (1) Front/Rear Base Bracket C. Attach Base Bracket C to the 3 factory studs with appropriate washers and nuts. Leave the bracket loose at this time.

Step 3:

• Select (1) Front/Rear Mounting Bracket A. Slide the tabs on the Mounting Bracket A into the slots in the Base Bracket C.
• Attach the Mounting Bracket A to the tab on the back of the Base Bracket C with the included bolts, washers, and nuts. Leave the bracket loose at this time.

INTRODUCTION

• READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT.
• FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO THE REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE IS FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE.
• TO FILE YOUR CLAIM, PLEASE VISIT: WWW.TYGERAUTO.COM/CONTACT

TORQUE VALUES

Fastener Size	Class 8.8 Torque (ft-lbs)	Class 10.9 Torque (ft-lbs)
6mm	6-7	6-7
8mm	15-16	22-23
10mm	31-32	44-45
12mm	54-55	78-79
14mm	87-88	125-126

PARTS LIST

Reference the letters printed on the brackets to determine mounting locations

Bottom View

ATTENTION: Refer to the D or P labelling on the tubes to determine the Driver or Passenger side steps.

PROCEDURE:

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.

INSTALLATION STEPS

1. STEP 1
   • Start the installation on the passenger/right side of the vehicle. Locate the front 3 factory studs along the inner sidewall of the body panel (Fig 1).
   • NOTE: Use a wire brush or thread die to remove paint buildup on the threaded studs.
   • Passenger/right side Installation Pictured
2. STEP 2
   • Select (1) Front/Rear Base Bracket © (Fig 2).
   • NOTE: The Front/Rear Base © and Mounting Brackets A are the same and fit both driver and passenger sides.
   • Attach Base Bracket © to the 3 factory studs with (3) 8mm x 24mm STD Flat Washers and (3) 8mm Nylon Lock Nuts (Figs 2 & 3).
   • Leave the bracket loose at this time.
   • Passenger/right side Installation Pictured
3. STEP 3
   • Next, select (1) Front/Rear Mounting Bracket A (Fig 4).
   • NOTE: The Front/Rear Base Cand Mounting Brackets A are the same and fit both driver or passenger sides. Slide the tabs on the Mounting Bracket into the slots in the Base Bracket ©.
   • Attach the Mounting Bracket A to the tab on the back of the Base Bracket © with the included (2) 8mm x 25mm Hex Bolts, (4) 8mm x 16mm Small Flat Washers, and (2) 8mm Nylon Lock Nuts (Figs 4 & 5). Leave the bracket loose at this time.
   • Passenger/right side Installation Pictured
4. STEP 4
   • Move to the center mounting location and locate the 3 mounting studs (Fig 6). Repeat STEP 1 to clear paint or undercoating from the studs.
   • Passenger/right side Installation Pictured
5. STEP 5
   • Select (1) Center Base Bracket D (Fig 7).
   • NOTE: Center Base D and Center Mounting Bracket are the same and fit both driver and passenger sides.
   • Attach the Base Bracket D to the 2 bottom factory studs with (2) 8mm x 24mm STD Flat Washers and (2) 8mm Nylon Lock Nuts (Figs 7 & 8). Leave the hardware loose at this time.
6. STEP 6
   • Next, select (1) Center Mounting Bracket B (Fig 2).
   • NOTE: The two Center Mounting Brackets B are the same and fit both driver and passenger sides.
   • Attach the Mounting Bracket B to the top factory stud and stud on Center Base Bracket D with (2) 8mm x 24mm STD Flat Washers and (2) 8mm Nylon Lock Nuts (Figs 9 & 10). Leave the bracket loose at this time.
   • Passenger/right side Installation Pictured
7. STEP 7
   • Move to the passenger/right rear mounting location (Fig 11).
   • Repeat STEPS 1-3 to clean the studs and attach (1) Front/Rear Mounting Base and (1) Front/Rear Mounting Bracket A to the rear mounting location along the body panel (Figs 2, 4 & 12).
   • Passenger/right side Installation Pictured
8. STEP 8
   • Select the Passenger/Right TYGER LanderX. Carefully position the TYGER LanderX up to the (3) Mounting Brackets.
   • IMPORTANT: DO NOT slide (front to back or rotate) the TYGER LanderX on the Brackets or damage to the finish may result.
   • Attach the TYGER LanderX to the (3) Brackets with (6) 8mm Combination Hex Bolts (Figs 13-17). DO NOT fully tighten at this time.
   • Passenger/right side Installation Pictured
9. STEP 9
   • Properly level and adjust the TYGER LanderX and fully tighten all hardware.

STEP 10

1. • Move to the driver’s/left side of the vehicle. Repeat STEPS 1-9 for Driver/Left TYGER LanderX installation.
2. STEP 11
   • Do periodic inspections of the installation to make sure that all hardware is secure and tight.

Customer Support

• Customer Support: www.tygerauto.com/contact
• Scan to Download the Latest Digital Version

FAQ

• Q: How do I determine the Driver or Passenger side steps?
  • A: Refer to the D or P labelling on the tubes to determine the Driver or Passenger side steps.
• Q: What is the weight capacity of the product?
  • A: The weight capacity is 300 lbs.

Documents / Resources

TYGER TG-LX3D82468 LanderX Triangular Drop [pdf] User Guide TG-LX3D82468 LanderX Triangular Drop, TG-LX3D82468, LanderX Triangular Drop, Triangular Drop, Drop

References

• User Manual