TMT AUTOMATION KP3 Wireless Keypad

Product Description

• The KP3wireless keypad isa dual channel transmitter that activates the opening cycle of your gate once the correct combination is entered.
• The KP3 Keypad can be installed both indoors and outdoors. The estimated range is 262.47 ft for outdoor and 65.62 ft for indoor, though actual range may vary depending on the environment.

Technical Data

Installation

1. Before installation, make sure the keypad is paired with the system that you want to use with it. Make sure that the designated mountipg positioniswithin communication range. Note that range may deteriorate as battery power goes low.
2. Having metal, concrete, orother obstacles may lower the range.
3. To Install:

Pairing the Keypad

To Pair the Keypad with the Gate System:

1. Press and hold the RF-Learn Button on the control board.
2. Press the , then press the default code, then press the.
3. Press the default code( ), then pressagain. A total of two times.
4. 1f the control board LED turns off or starts flashing, the password setup is complete.
5. Verify that the system has been learned by entering the code on the keypa,d followed by the enter button.

• If you would to like pair your keypad to two different systems, you may repeat the same steps as above, except just make sure to assign a different system to a different channel.

Setting the Combination Code

Press any button on the KP3, and the LED on the KP3 will flash once. If no further button is press ed within 3 seconds, the state will be cleared. If no button is press ed within 30 seconds, the device will enter sleep mode. After entering sleep mode, press any button to wake the device.

• The keypad supports two sets of codes, using either .
• The two arrow keys are used to enter the key combination.
• By default, the factory codes for the channels ar.
• It is recommended that you pair the keypad with your system before changing the combination.
• Valid code lengths are between 3 and 8digits inclusive.
• To Change the Key Code:
  1. Press to enter modification mode. In modification mode, all LEDs will remain lit for 10 seconds. The 10-second timer resets with each key press. If no key is pressed within 10 seconds, the LEDs will turn off, and the buzzer will beep five times to exit the modification mode.
  2. Enter the factory default code () (or the previously set code), then press.
  3. Enter the new code (minimum of 3 digits, maximum of 8 digits), then press .

Keypad Operation

• The keypad supports two channels. The arrow keys act as the enter button for each channel.
• You may heara number of different beeps to signal a different status.
• Entering the correct key combination is analogous to pressing the remote. If you enter the combination while your gate is in motion, it will send another signal to the gate to move it to the next state (usually most systems follow an open- open-stop-close-stop cycle). Similarly, entering the key when the gate is open will usually close it.

Reset

• If you forget the code, you can reset the keypad, which will revert the codes to the factory setting and
• You can reset the system by holding the button on the back of the circuit board.

FCC Statement

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment hasbeen tested andfound to comply with the limits for a ClassB digital device, pursuant to part 150f the FCC Rules. These limits are designed to provide reasonable protection against harmful interference ina residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer oran experienced radio/ TV technician for help.

Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment. The device has been evaluated to meet general RF exposure requirements. To maintain compliance with the FCC’s RF exposure guidelines, the distance must be at least 20 cm between the radiator and your body, and fully supported by the operating and installation

Frequently Asked Questions

• Q: How do I reset the device to factory settings?
  • A: Press the button to reset codes to the factory setting.
• Q: What is the working temperature range of the device?
  • A: The working temperature range is not specified in the provided information. Please refer to the product manual for detailed specifications.

Documents / Resources

TMT AUTOMATION KP3 Wireless Keypad [pdf] User Guide 2BOT8-KP3, 2BOT8KP3, kp3, KP3 Wireless Keypad, KP3, Wireless Keypad, Keypad

References

• User Manual