User manual
In Dash Speaker
Model: YAMATRACK B

Basic Specification

Bluetooth Version BT5.3
Bluetooth Pairing Name YAMATRACK B
Support Profiles HFP V1.5; A2DP V1.2; AVRCP V1.4, GAVDP V1.2; AVDTP V1.2; SPP V1.2; AVCTP V1.2 HFP
Audio Decoding SBC
RF Carrier Frequency 2402MHz – 2480MHz
Bluetooth Working Distance 10 meters
Mobile Power Supply Support 5V / 2A: type_c output * 1, USB – A output * 1
Output Power 15W * 2
SPL 95 ± 3dB (BT in 200mv / 1m) 500Hz – 14KHz
Channel 2.0 S / N ≥ 74dB
Frequency Range 100Hz – 20KHz / – 10dB
THD ≤ 1% at 1KHz 1M / 1W
Automatically Turn Off Time (Bluetooth Unconnected) 30 minutes
Speaker Driver
Size 67mm * 67mm ± 0.5mm 2”
Quantity 2PC
Impedance 4Ω ± 15%
Rated Power 15W
Frequency Response 100Hz – 20KH
Nominal Voltage External power supply DC_48V
Electric Power Parameter
Input voltage / current External power supply DC = 48V 5A
Output voltage / current Supply for external use: DC = 12V 2A
Waterproof Grade IPX7
Material ABS
Product Size 237mm * 159.1mm * 156.5mm ± 0.5mm
Product Weight 810g ± 20g

Operation Instruction

1. Power On Long press the power button for 1 second in the off state
2. Power Off Long press the power button for about 1 second in the on state
3. Turn on Bluetooth Pairing
   1) Click the Bluetooth button to turn on Bluetooth and enter the pairing mode after power on.
   2) Reconnect the last connected Bluetooth device
4. Pairing Successful Select the Bluetooth name on the mobile phone: *******
5. Turn off Bluetooth Click the Bluetooth button to turn off the Bluetooth mode in the Bluetooth mode
6. Volume Up Short press the volume plus button: the volume increases in a single step in the Bluetooth and call modes.
7. Volume Down Short press the volume minus button: the volume decreases in a single step in the Bluetooth and call mode
8. Next Song Long press the volume plus button for 1 second
9. Previous Song Long press the volume minus button for 1 second
10. Pause / Play Click the play / pause button
11. TWS Pairing
    1) Click the BT button to enter the Bluetooth mode, and then double – click the BT button to enter the TWS mode when
    Bluetooth is not connected.
    2) Two machines paired with TWS will reconnect to TWS after entering the Bluetooth mod
12. TWS Connect to Mobile Phone After the TWS connection is successful, search for Bluetooth on the mobile phone and connect

*Note:

1. The volume has a memory function, and it will continue the volume of the last shutdown every time it is powered on, and the volume is synchronized with the mobile phone.
2. The incoming call answering and call transfer functions are completed by the mobile phone.
3. To detect the physical function of the BLE button: long press the BLE button and the power button at the same time, and the red light flashes twice. Federal Communications Commission (FCC) Statement. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide Reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  Warning: Changes or modifications made to this device not expressly approved by Rad Golf, Inc. may void the FCC authorization to operate this device.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. RF exposure statement:
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

ISED Statement

This device contains license-exempt transmitter(s)/receiver(s) that comply with lnnovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment must be installed and operated with a minimum distance of 20 cm between the radiator and your body.

Documents / Resources

Syncwise YAMATRACK B In Dash Speaker [pdf] User Manual YTSG1, YAMATRACK B In Dash Speaker, YAMATRACK B, In Dash Speaker, Speaker

References

• User Manual