SVB JK65X Built In Refrigerator User Manual

The product features include door latch, door bins, control
panel, freezer compartment, and fridge compartment for JK65X model.
For the JK90X model, features include interior LED light, shelf,
crisper drawer, and compressor.

Installation

Precautions before installation: Check for
damages and report any transportation damage. Handle with care.

Step 1: Prepare the cabinet by ensuring proper
ventilation space around the refrigerator and keeping it on a
horizontal surface away from heat sources.

Step 2: Connect the refrigerator to a 12/24V DC
power supply. Ensure not to place multiple power supplies at the
rear of the device.

Step 3: Carefully push the fridge into the
cabinet to avoid scratching the floor. Keep the power cable
loose.

Step 4: Fix the refrigerator using one of three
methods:

– Method 1: Mount the fridge with the cabinet wall using screws
(not included).

– Method 2: Use an optional installation frame for a secure fit
and finish.

FAQ

Q: Can I use power supplies at the rear of the
refrigerator?

A: It is not recommended to locate multiple power supplies at
the rear of the device to avoid potential hazards.

Q: How should I dispose of the appliance?

A: Dispose of the appliance according to local regulations
regarding its refrigerant and blowing gas for proper environmental
practices.

“`

View Fullscreen

USER MANUAL

JK65X

JK90X

2025 SVB – Spezialversand für Yacht- und Bootszubehör GmbH

CONTENTS 1.SAFETY INSTRUCTIONS 2.PRODUCT FEATURES 3.PRODUCT STRUCTURE 4. INSTALLATION 5.REVERSEDOOR OPEN DIRECTION 6.FUNCTION AND OPERATION 7.CARE AND MAINTENANCE 8.TROUBLESHOOTING 9.WARRANTY 10.TECHNICAL INFORMATION

Page 1 Page 3 Page 3 Page 3 Page 6 Page 6 Page 8 Page 9 Page 10 Page 10

2025 SVB – Spezialversand für Yacht- und Bootszubehör GmbH

SAFETY INSTRUCTIONS
do not operate the appliance if it is visibly damaged. · Do not block the gaps of the fridge with things like pin, wire, etc. · Do not expose the appliance to rain or soak it in water. · Do not place the appliance near naked flames or other heat sources (heaters, direct sunlight,
gas ovens etc.) · Do not store any explosive substances like spray cans with a flammable propellant. · Ensure the supply cord is dry and not trapped or damaged. Do not locate multiple portable
socket-outlets or portable power supplies at the rear of the appliance. · Check the voltage specification on the type plate corresponds to that of the energy supply.
The appliance is only to be used with the power supply unit provided with the appliance. · Do not use electrical appliances inside the food storage compartments of the appliance,
unless they are of the type recommended by the manufacturer. · Once unpacked and before turning on, the appliance must be placed on a level surface for
more than 6 hours. · Make sure that the appliance stays horizontally when it is running. The tilt angle must be less
than 5° for long time running and be less than 45° for short time running. · Keep the ventilation openings in the unit casing or in the built-in structure free of obstacles. · Keep the appliance stable on the ground or in the car; Do not drain upside down. · When positioning the appliance, ensure the supply cord is not trapped or damaged. · Do not locate multiple portable socket-outlets or portable power supplies at the rear of the
appliance. · Risk of child entrapment. Before you throw away your old refrigerator or freezer: *Takeoff the doors. * Leave the shelves in place so that children may not easily climb inside.
Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
Risk of fire/ flammable materials.
CAUTION!
· Repairs may only be carried out by qualified personnel. Incorrect repair may cause danger. The lamp and supply cord must be replaced by the manufacturer or qualified persons.
· The installation of DC power in the boat must be handled by qualified electricians. · Children shall not play with the appliance. Cleaning and user maintenance shall not be made
by children without supervision.
2025 SVB – Spezialversand für Yacht- und Bootszubehör GmbH

· The appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they’ve been given supervision or instruction concerning use of the device in a safe way and understand the hazards.
NOTICE! · Disconnect the power supply before each cleaning and maintenance and after every use. · Do not use sharp tools to defrost; Do not damage the refrigerant circuit. · Risk of child entrapment. Before you throw away your old refrigerator or freezer: take off the
doors: leave the shelves in place so that children may not easily climb inside. · Check if the cooling capacity of the appliance is suitable for storing the food or medicine.
Food may only be stored in its original packaging or in suitable containers. · If the appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the
door open to prevent mould developing within the appliance. · The appliance is intended to be used in household and similar applications such as:
– Staff kitchen areas in shops, offices and other working environments; – Camping, Farm houses and by clients in hotels, motels and other residential environments; – Bed and breakfast type environments; – Catering and similar non-retail applications. · To avoid contamination of drink, please respect the following instructions: – Opening the door for long periods can cause a significant increase of the temperature in the compartments of the appliance. – Clean regularly surfaces that can come in contact with drink and accessible drainage systems. – Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food; – Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food.
If the refrigerating appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the door open to prevent mould developing within the appliance.
Please according to local regulations regarding disposal of the appliance for its flammable refrigerant and blowing gas.
2025 SVB – Spezialversand für Yacht- und Bootszubehör GmbH

PRODUCT FEATURES
· High-efficiency DC compressor and conversion module. · CFC free and great heat insulation. · Intelligent battery protection system prevents your vehicle from running out of battery. · Dual temperature with single controller, LED display control panel for temperature setting. · Easy to install, reversible door. · Detailed designs: removable door bins, crisper drawer, removable wire shelves, interior LED light, night light for control panel.
PRODUCT STRUCTURE

CR65X
Door latch Door bins Control panel Freezer Compartment Fridge Compartment

CR90X
Interior LED light Shelve Crisper drawer Compressor

INSTALLATION
Precautions before installation: Ensure that the fridge is not damaged when opening the package after receiving the product. Any transportation damage could be reported to the place of purchase. Handle the product with the utmost care and attention.

2025 SVB – Spezialversand für Yacht- und Bootszubehör GmbH

STEP 1: Prepare the cabinet. Leave space around the refrigerator to keep good ventilation. (the back and top S0mm, the side 20mm). Always keep the fridge on a horizontal surface and away from heat sources.

There should be a minimum of 50mm of space at the rear and top of the refrigerator and 20mm on each side.

Model CR65X CR90X

Product Dimension Recommended Installation

(A*C*B)

Dimension(Al *Bl *Cl)

470*431*630mm

520*481*680mm

418*468*976mm

468*518*1026mm

STEP 2: Connect to a power supply. Connect the refrigerator to the vehicle 12/24V DC system directly ( *Note: The plug and power-supply cord are not included in the standard configuration). Do not locate multiple portable socket-outlets or power supplies at the rear of the device.

STEP 3: Push the fridge into the cabinet carefully to avoid scratching the floor, and the power cable should be kept loosen.

STEP 4: Fix the refrigerator. There are three methods you can choose:

-Method 1:Mount the fridge with the cabinet wall. The screw holders

is built in

the side wall of the refrigerator, a hole needs to be drilled through the screw holders into the

side metal panel with screws (MS, 15mm minimal and fix it on the wall; after that, use the

screw cover to cover the hole. (If the refrigerator i s to be drilled through, it should be

confirmed before leaving the factory. The screws are not included with the refrigerator.)

inner seal foam cap screw inner seal foam holder

(CR65X for example)
2025 SVB – Spezialversand für Yacht- und Bootszubehör GmbH

-Method 2: Optional installation frame (standard frame or flush-mount frame) for a secure fit and a smart finish (as shown below).

Unscrew the screws on the refrigerator and place the frame behind the door to fix it.

Fix the frame to the refrigerator with screws and then push the refrigerator into the cabinet.
EXAMPLE-2 Optional standard frame

Fix the refrigerator to the cabinet through the frame.

Unscrew the screws on the refrigerator and fix the frame flush with the door.

Fix the frame to the refrigerator with screwsand then push the refrigerator into the cabinet.

Fix the refrigerator to the cabinet through the frame.

EXAMPLE-3 Optional flush-mount frame

STEP 5: Verify the installation. Once the installation had been finished, check the continuity of the earth circuit and carry out all electrical safety testing provided for by current regulations. Protect and fix the cables in order to prevent accidental pulling of the cable from disconnecting it from the connections or coming into contact with hot parts with a temperature above 50° C or with sharp parts. *Note: Recommended installation dimensions are for reference only, please refer to the actual product for sp2e0c2if5ic dSiVmBen- sSiopneszialversand für Yacht- und Bootszubehör GmbH

Reversible door that can be opened from left to right or from right to left. Follow the steps below if necessary : 1.Unscrew the bottom hinge component and take off the door body (keep the fridge stable), unscrew the door axle; 2.Unscrew the bottom hinge and fasten it to the other side of the fridge. 3.Fixed the door axle to the other side, and install the door to the other side of the refrigerator; fasten the bottom hinge component; screw the door with the hinges, the door opening direction is now reversed.

Bottom hinge component

Bottom hinge

Bottom hinge component

(CR65X for example)

FUNCTION AND OPERATION

TEMPERATURE CONTROL

NIGHT LIGHT

FREEZER

REFRIGERATOR

SET ON / OFF

· Power Supply: DC 12V/24V or AC 100-240V power (using dedicated adapter). · Display Screen Initialization: when the fridge is powered on, the buzzer will make a long beep, and the display will be on for one second then enter the normal operation. · Power ON/OFF: press to switch ON/OFF.

2025 SVB – Spezialversand für Yacht- und Bootszubehör GmbH

· Temperature Setting: under the running state, press + or – to adjust the temperature

of the freezer compartment. Press + to increase the temperature, press – to decrease the

temperature, long press + or – to fast adjust the temperature. Press to switch the

freezer and refrigerator temperature setting. The temperature displayed is the current

temperature of the compartment, it will take a while to reach the set temperature.

The range of temperature adjust: fridge: 0~8°C (32~46°F); freezer: -12~-20°C (10~-4°F).

Note: The temperatur is based on the last set temperature of either the freezer or refrigerator compartment If the refrigerator compartment nt was set last, the freezer

temperature will change accordingly,if the freezer compartment was set last, the refrigerator temperature will change accordingly .

· Night mode: under running state, long press for 3 seconds to enter Night mode, the

screen will turn off and the night light will be on. Short press again to return to normal

display.

· Battery Protection Mode: under the running state, long press for 3 seconds until the left

screen flashes, then pres

gain to switch High, Medium and Low (*Factory setting is High).

From left to right: Low/Medium/High.

Voltage refer

INPUT

DC 12V

DC 24V

MODE L

CUT OUT 8.SV

CUTIN 10.9V

CUT OUT 21.3V

CUTIN 22.7V

10.lV

11.4V

22.3V

23.7V

11.lV

12.4V

24.3V

25.7V

* the voltage is theoretical value, there may be a deviation in different sceneries. * H should be set when the product is connected to car power, and M or L should be set when it is connected to a portable battery or other back-up battery. · Temperature Unit Setting: switch OFF the fridge, long press for 3 seconds until displays E1, and switch to E5 by pressing again, then press + or – to switch Celsius or Fahrenheit. (*Factory setting is 0c.) Reset: switch OFF the fridge, long press for 3 seconds until displays E1, under E1 mode, long press + und – at the same time for seconds to reset the settings. · Recommended temperature for common food:

2025 SVB – Spezialversand für Yacht- und Bootszubehör GmbH

CARE AND MAINTENANCE
Cleaning: Unplug the device first to avoid electric shock. Use wet cloth to clean the device and dry it. Remove the cover and drain the hole at the bottom of the device. Do not soak the device in water and do not wah it directly. Do not use abraisve cleaning agents as these can damage the device. Storage: If the device will not be in use for a long time, please follow the steps: Turn off the power and remove the plug. Remove all the items stored in the device. Remove the cover and drain from the hole, wipe off excess water with a soft rag. Put the device in a cool and dry place.
Defrosting:
Humidity can form frost in the interior of the cooling device or on the evaporator, which will affect the cooling performance. Defrost the device regularly to avoid this. · Switch off the device. · Take out the contents of the device. · Remove the cover and drain from the hole. · Keep the door on. · Wipe off the dd water.
Never use hard or sharp tools to remove ice or to loosen objects which have frozen in place.
2025 SVB – Spezialversand für Yacht- und Bootszubehör GmbH

TROUBLESHOOTING

Issues

Cause/Suggestions

Refrigerator does not work
Refrigerator compartments are too warm Food is frozen

· Check if the switch is on. · Check if the plug and socket are connected well. · Check if the fuse has been burnt. · Check if the power supply is malfunctioned. · Switch on/off the fridge frequently may cause start delay of the compressor. · The door is opened frequently. · A large amount of warm or hot food was stored recently. · The refrigerator has been disconnected for a long time.
· The temperature was set too low.

There is “water flow” noise from inside the refrigerator

· It’s a normal phenomenon, caused by the flow of refrigerant.

There are waterdrops around the refrigerator · It’s a normal phenomenon, the moisture will condense to

casing or door gap

water when it touches a cold surface of the refrigerator.

The compressor is slightly noisy when starting
Code Fl displayed

· It’s a normal phenomenon, the noise will be reduced after the compressor works stably.
· Possible cause: low voltage to fridge. Adjust the battery protection from High to Medium or from Medium to Low.

Code F2 displayed Code F3 displayed Code F4 displayed Code FS displayed

· Possible cause: condenser fan is overloaded. Disconnect power to fridge for 5 minutes & re-start. If the code shows again, contact manufacturer for service.
· Possible cause: the compressor starts too frequently. Disconnect power to fridge for 5 minutes & re-start. If the code shows again, contact manufacturer for service.
· Possible cause: compressor not kicking in. Disconnect power to fridge for 5 minutes & re-start. If the code shows again, contact manufacturer for service.
· Possible cause: overheating of the com ressor & electronics. Disconnect power to fridge for 5 minutes & re-start. If the code shows again, contact ma rer for service.

Code FG displayed

· Possible cause: no parameter can be detected by the controller. Disconnect power to fridge for 5 minutes & re-start. If the code shows again, contact manufacturer for service.

Code F7 or FB displayed · Possible cause: temperature sensor is faulty. Contact manufacturer for service.

2025 SVB – Spezialversand für Yacht- und Bootszubehör GmbH

WARRANTY
If the device gets malfunctional, limited warranty will be provided for 1 year from the date of purchase, except following situations: · Contrived damage. · Damage caused by force majeure such as earthquake, conflagration, etc. · Damage from inappropriate use or violating this instruction. · Damage or malfunction caused by disassembling.

TECHNICAL INFORMATON

MODEL
RATED VOLTAGE
RATED POWER
TOTAL CAPACITY FRIDGE COMPARTMENT CAPACITY FREEZER COMPARTMENT CAPACITY NOISE TEMPERATURE SETTING RANGE CLIMATE CATEGORY
DIMENSIONS(L*W*H)
NET WEIGHT

JK65X

JK90X

DC12/24V or ACl00~240V(using dedicated adapter)

60W

80W

58.4L/2.06 Cu.Ft.

92.9L/3.28 Cu.Ft.

44.7L/l.58 Cu.Ft.

83.2L/2.94 Cu.Ft.

13.7L/0.48 Cu.Ft.

9.7L/0.34 Cu.Ft.

<4sdB Refrigeration: 0~8°C (32~46°F) Freezer: -12~-20°C (10~-4°F)
T/ST/N

470*431*630mm 181/2*16 5/8*2413/16 inch
19.1kg/42.1lb

418*468*976mm 161/2*18 7/16*38 7/16 inch
22.3kg/49.2lb

*Due to product improvement, the technical information might be different from actual information, please refer to the rating label on the product.

2025 SVB – Spezialversand für Yacht- und Bootszubehör GmbH

Documents / Resources

SVB JK65X Built In Refrigerator [pdf] User Manual
JK65X, JK90X, JK65X Built In Refrigerator, JK65X, Built In Refrigerator, Refrigerator

References

User Manual

SVB JK65X Built In Refrigerator User Manual

JK65X Built In Refrigerator

Specifications

Product Usage Instructions

Safety Instructions

Product Features

Installation

FAQ

Q: Can I use power supplies at the rear of the
refrigerator?

Q: How should I dispose of the appliance?

Documents / Resources

References

Leave a comment

Cancel reply