CLEANING & MAINTENANCE
Product Care Guide
stonebaths.com.au
stonebaths.co.nz
Warranty
Failure to follow the care and maintenance instructions outlined in this manual will void your warranty. For full warranty terms and conditions, including exclusions and claim procedures, please visit our website at www.stonebaths.com.au or www.stonebaths.co.nz.
POLYMARBLE AND SOLID SURFACE
 |
Everyday cleaning Polymarble and solid surface baths can be cleaned with Jif/ Ajax or warm soapy water and a cloth. Clean any bath water residue after each use. DO NOT use toilet cleaner, bleach or ammonia based products. |
 |
Coloured baths & basins Follow the cleaning instructions as above. Chip/dented/ stained surface – Clean and dry the surface. Use a 4000 grit wet/dry sandpaper to very gently polish using a circular motion. |
 |
Stains, scuffs and marks To avoid products staining, always wipe up spills immediately. Avoid the use of fake tan, hair dyes or coloured shampoo. To remove scuffs or small marks use a 4000 grit sandpaper in a circular motion. |
 |
Repairing damage Chip/dented/stained surface – Clean and dry the surface. Use a 4000 grit wet/dry sandpaper to polish/buff the mark or chip out. For coloured baths this can then be followed by a polishing wax (car wax). |
For further information or for a chip repair kit please contact Stonebaths.
THE COPPER BATH TUB COLLECTION
 |
Everyday cleaning After each use, rinse away any residue with clean water and dry the surface with a soft cloth to help prevent water spots. For a more thorough clean, use mild dish soap and a non-abrasive sponge or cloth as needed. |
 |
Natural aging Over time, your copper bath will naturally develop a patina that forms through oxidation. Often referred to as a “living finish,” this process results in a mix of tones that enhances the character of the metal and protects it from corrosion. |
 |
Repairing damage Using a soft microfiber cloth, apply a small amount of highquality copper polish. Rub in a circular motion until scratch diminishes and the surface regains its shine. |
KEL ACRYLIC BATHS
 |
Everyday cleaning Clean with warm soapy water or any bathroom cleaner that is safe on acrylic finishes. |
 |
Cleaning stains For light stains, mix baking soda with water into a paste and gently rub with a soft cloth. |
 |
Preventing scratches Never use steel wool or abrasive pads. Restore shine with a polish made for acrylic surfaces, applied gently with a microfiber cloth. |
THE RAMP BASIN COLLECTION
 |
Everyday cleaning Ramp basins are made from solid surface. Clean with Jif/Ajax or warm soapy water and a cloth. For trough style, use a soft brush to clean in corners. DO NOT use toilet cleaner, bleach or ammonia based products. |
 |
Coloured finishes Follow the cleaning instructions as above. Chip/dented/ stained surface – Clean and dry the surface. Use a 4000 grit wet/dry sandpaper to very gently polish using a circular motion. |
 |
Stains, scuffs and marks To avoid products staining, always wipe up spills immediately. Avoid the use of fake tan, hair dyes, coloured shampoo etc. To remove scuffs or small marks use a fine grit sandpaper in a circular motion. |
 |
Repairing damage Chip/dented/stained surface – Clean and dry the surface. Use a 2000 grit wet/dry sandpaper to polish/buff the mark or chip out. This can then be followed by a polishing wax (car wax). For further information please contact Stonebaths. |
GIA ITALLII VANITIES
Everyday cleaning
|
Solid surface (tops, basins) Clean with Jif/Ajax or warm soapy water and a cloth. DO NOT use toilet cleaner, bleach or ammonia based products. |
|
MDF cabinetry Clean with a soft cloth and warm soapy water. Ensure surfaces are fully dried. |
OUTDOOR SHOWERS
Our 316 stainless steel showers and freestanding bath spouts are crafted to resist corrosion and withstand outdoor conditions. However, due to environmental factors such as salt air, humidity, and pollutants, rust spots may occasionally develop over time. This is a natural occurrence with stainless steel in outdoor environments and does not affect the structural integrity of your shower. To avoid this occuring prematurely, a daily cleaning as described above is recommended.
 |
Everyday cleaning Clean regularly with fresh water and a soft cloth. Use warm water and mild soap for deeper cleaning, avoiding abrasive cleaners or tools. Always rinse well and dry to prevent water spots. |
 |
Removing marks For rust spots, gently apply a stainless steel cleaner with a soft cloth following the metal grain. Rinse and dry thoroughly afterward. |
Rinse after exposure to salt or chlorine and check fittings regularly. Coastal or humid environments may require more frequent cleaning to manage surface rust.
TOKA TAPWARE
|
Everyday cleaning Clean with a soft cloth and warm soapy water. Dry regularly to ensure no water marks or stains. Do not use abrasive cleaners, bleach or ammonia or scourer cleaning cloths. |
|
Removing limescale Soak a soft non-abrasive cloth in a natural citric acid then apply to your tapware. Rinse with clean water. |
AUSTRALIA
T: 1800 462 946
E: info@stonebaths.com.au
NEW ZEALAND
T: 0800 001 872
E: info@stonebaths.co.nz
stonebaths.com.au
info@stonebaths.com.au
Documents / Resources
 |
Stonebaths Lightweight Baths and Basins [pdf] User Guide DAGdiQAHUBQ, BAClChW04EU, Lightweight Baths and Basins, Baths and Basins, Basins |