Create the Flat Install USB Stick

1. Download the Live V5.2.18 software image file using the link above.
2. [Optional] Run a checksum on the downloaded file using WinMD5. The checksum value is: cc384499016ee6418eb47980481bd764
3. Download Rufus 3.5 and run the .exe application. Select the software image file in Boot selection, choose the correct USB drive under Device, and ensure the Partition scheme is set to GPT.
4. Enter a suitable Volume label so that the drive can be identified in future. e.g. Live V5.2.18 Flat Installer
5. Select Start and Confirm that you wish to erase all data on the USB drive by clicking OK. Rufus will now partition your device and copy the files. (USB2 will take approximately 30mins, USB3 5mins)
6. Once the process is complete there will be an ‘Important notice about Secure Boot’. This can be ignored – press Close. The USB Flat Installer is now ready to be used.
   

Please Note: A USB memory stick that identifies itself as a fixed hard disk will not be suitable for this update. Use a USB stick that identifies itself as a removable storage device.

Install Console Software

Preparation and Update Order

1. Backup of system files – insert a spare USB drive (not Flat Installer) then navigate to Menu>Setup>System/Power to use the Backup Data function.
2. Load a blank show file template – clears routing and relinquishes any ownership.
3. Set console to Internal clock and 96 kHz operational mode.
4. Power off the console.
5. Remove external screen connections.
6. Remove or power off ancillary I/O, network and USB devices not required for the update.
7. Update console FPP Control Software (flat install).
8. Automatic OCP (DSP Engine) software updates.
9. Update Control Surface tiles/assembly firmware from GUI.
10. Network I/O V4.4 Package updates
11. Other updates including SOLSA and TeamViewer re-installation where relevant.

Operating System & Control Software Update

1. Insert the USB install stick and a keyboard to any available USB ports.
2. Power on the console and tap F7 on the keyboard continuously to open the Boot Manager menu. Note that the appearance of this menu may differ between consoles.
3. Use the Up/Down arrow keys on the keyboard to select the UEFI/EFI device as per the screenshots below, then press Enter. The console will now boot from the installer.
   
4. A screen showing ‘Windows is Loading Files….’ will appear for a few minutes, then a Command Prompt window ‘Solid State Logic Tempest Installer’ will be shown with a list of selection options numbered 1-6.
   Choose option 1) Install image and KEEP user data. This retains the existing console configuration.
   
5. Progress will be shown at the bottom of this window as a percentage, taking approximately 5 minutes to complete. Upon completion, the message ‘The operation completed successfully. Please press 1 to REBOOT.’ is displayed. Follow the onscreen instruction and press number 1 on the keyboard to reboot:
   
6. Windows Setup will begin with various progress screens and automatic restarts during this process. At times it may look like the installer is not active and your screen may go blank with a ‘No Input’ or ‘Out of range’ message.
   Be patient and DO NOT power cycle the console during this process. When complete the console will boot into the usual Front Panel display/console GUI.
7. Navigate to MENU>Setup>System and verify that the Current Version numbers for the Control Software and Operating System match those listed in the table above.
8. Restart the console once more to permit the console name file to be read correctly.

OCP Software (automatic)

This process is automatic and will happen within three minutes of the FPP booting into the new software. Menu>Setup>System/Power will show ‘Automatic Update Pending’ next to the OCP Software entry, followed by ‘Error: Connection Lost’ for both this and OCP 020 Card. This is a result of code being downloaded and the OCP rebooting itself. Connection will reestablish itself shortly afterwards. Upon reconnection both the OCP and OCP 020 card will display their current version. Refer to the ‘Console Software & Firmware Overview’ table earlier in this document to confirm these.

OCP 020 Card (as required)
No update is required if the console was already running V4.11.x previously. If updating a console from V4.10.17 software the OCP 020 card will show a required update. Press-and-hold the Update button. Upon completion, restart the console and confirm the programmed version is correct, referencing the ‘Console Software & Firmware Overview’ table.

Update Surface Tiles
The Menu>Setup>System/Power page lists all connected control surface tiles and internal card assemblies that can be programmed. Required control surface updates are automatically prompted and can be completed in any order. Press-and-hold the active Update button(s). The screen and surface will be locked out while each update is in progress. Control surface tiles will  automatically restart and reconnect upon completion. Repeat the process for all required tiles.

Additional Updates/Installations

Network I/O Updates
The Network I/O V4.4 Package includes all firmware and required applications for Network I/O stage boxes and other SSL Dante devices. Refer to the V4.4 Package documentation.
Please Note: Recent Network I/O devices use Bk3 instead of BkII modules; features are the same across both versions but the .dnt firmware files differ. Refer to the Firmware/Software tables above as well as the details in the Network I/O V4.4 Package documentation.

Live SOLSA Software
Download the package then refer to the included installation notes.

Installing TeamViewer
Contact your local SSL Distributor or SSL Support office to obtain a service code and full instructions if this feature is required. Instructions are available on the SSL Support site for registered Live users – see Live Application Note 021.

Installing/Updating SSL Live TaCo Apps
TaCo’s version number is displayed in the bottom right corner of the TaCo app. A new version of TaCo was released for V5.x console software – refer to the tables above for more information.

The TaCo app can be found in the app stores by searching “SSL Live TaCo” or from these links:
Download SSL Live TaCo from the iOS App Store
Download SSL Live TaCo from the macOS App Store
Download SSL Live TaCo from the Google Play Store

If already installed and automatic app updates on your device are set to “Off” (recommended), the SSL Live TaCo app will need to be updated manually as below.

Updating TaCo on Android, iOS and macOS Devices:

1. Connect your device to the internet and open the App Store (Apple devices) or Google Play Store (Android devices).
2. Search for ‘SSL Live Taco’ then select it to open the App details page.
3. Select Update.

Software Licence Agreement

By using this Solid State Logic product and the software within it you agree to be bound by the terms of the relevant End User Licence Agreement (EULA), a copy of which can be found at https://www.solidstatelogic.com/legal. You agree to be bound by the terms of the EULA by installing, copying, or using the software.
Written Offer for GPL and LGPL Source Code Solid State Logic uses Free and Open Source Software (FOSS) in some of its products with corresponding open source declarations available at https://www.solidstatelogic.com/legal/general-end-user-license-agreement/free-open-sourcesoftware-documentation. Certain FOSS licenses require Solid State Logic to make available to recipients the source code corresponding to the FOSS binaries distributed under those licenses.
Where such specific license terms entitle you to the source code of such software, Solid State Logic will provide to anyone upon written request via e-mail and/or traditional paper mail within three years after the distribution of the product by us the applicable source code via CD-ROM or USB pen drive for a nominal cost to cover shipping and media charges as allowed under the GPL and LGPL.
Please direct all enquiries to: support@solidstatelogic.com

Visit SSL at:
www.solidstatelogic.com
© Solid State Logic