WT-DMX-M Lighting Control System
Product Information
Specifications
- Product Name: WT-DMX-M
- Model: WiFi & RF 3 in 1 DMX512 Master
- Input Voltage: 12-36VDC
- Output Signal: DMX512 (multipixel)
- Channel Output: Max 512 channels RGB: 170 pixels, RGBW: 128
pixels, RGB+CCT: 102 pixels - Operation Temperature: -20°C to +55°C
- IP Rating: IP20
- Warranty: 5 years
Product Usage Instructions
Connection and Installation
1. Connect the WT-DMX-M to the power input using the provided DC
socket input.
2. Ensure correct polarity with power input (+ and -).
3. Install the device in the desired location using the
installation rack.
Functionality
The WT-DMX-M supports various functions including on/off
control, brightness adjustment, dynamic mode change, and speed
settings.
Wiring Diagrams
1. To connect with DMX512 spot light:
- Connect the power supply (AC100-240V) to WT-DMX-M input
(12-36VDC). - Use Push switch 1 for on/off control and Push switch 2 for
dynamic mode changes.
2. To connect with DMX512 pixel strip:
- Connect the power supply (AC100-240V) to WT-DMX-M input
(12-36VDC). - Use Push switch 1 for on/off control.
FAQ
Q: What is the maximum channel output of the WT-DMX-M?
A: The WT-DMX-M supports a maximum channel output of 512
channels for RGB, RGBW, and RGB+CCT configurations.
Q: What are the supported control methods for the
WT-DMX-M?
A: The WT-DMX-M supports control via WiFi, RF 2.4G, push
switches, and Tuya Smart APP cloud control.
WT-DMX-M
WiFi& RF 3 in 1 DMX512Master
Features
WiFi & RF RGB/RGBW/RGB+CCT 3-in-1 DMX512 master, Max 512 channel output. Comply with the DMX512 standard protocols,
compatible with DMX decoder from other supplier. Tuya Smart APP cloud control. Voice control, support for Amazon Alexa, Google Assistant,
Tmall Genie and Xiaodu voice assistant. Painted segment color mixing: full color lling,
color pencil segment painting, eraser segment light off. Rich dynamic effects:
44 default and 10 + custom dynamic scenarios, 16 variations. 3 APP music rhythms. Connect with external two push switch, supports on/off, brightness adjustment,
dynamic mode change type and speed settings. Match with RF 2.4G remote control optional, such as R9.
DMX512
Technical Parameters
InputandOutput
Input voltage
12-36VDC
Input signal
WiFi, RF 2.4G, Push switch
Output signal
DMX512 (multipixel)
Channel number (Pixel Dots)
Max 512 Channel RGB: 170 pixels RGBW: 128 pixels RGB+CCT: 102 pixels
Environment
Operation temperature Ta: -20 OC ~ +55OC
Case temperature(Max.) Tc: +65OC
IP rating
IP20
Safety and EMC
EMCstandard
EN IEC 55015/ EN IEC 61547 ETSI EN 301 489-1/-3/-17
Safety standard EN 61347-1/-2
Radioequipment
ETSI EN 300 440 ETSI EN 300 328
Package
Certification
CERoHS
Size Grossweight
L120 x W43 x H27mm Warranty and Protection
0.055kg
Warranty
5 years
Protection
Reverse Polarity
Mechanical Structures and Installations
Power input +
Power input –
INPUT 12-36VDC
Installation rack
DC socket input LED indicator Match/Set key
RUN MATCH/SET
WT-DMX-M
WiFi & RF 3 in 1 DMX512 Master
Uin=12-36VDC Out=DMX512 (Multipixel) Temp range: -20~+55
Light type:
RGB
RGBW RGB+CCT
Red
Green Blue
Push func:
P1 On/Off
P2 Mode
114.00 mm
DMX OUTPUT
PUSH INPUT
D+ D- GND P2 GND P1
Push switch 1 Push switch com Push switch 2 Installation rack GND DMX output DMX output +
38.00 mm
User Manual Ver 1.0.1 2025.7
20.00 mm
SystemWiring
3G/4G/5G WiFi
Tuya Cloud
Wired connection Wireless connection
RGB-SPI
WiFi Mobile Phone
15m WiFi Router
Smart speaker 30m
DMX spot light DMX pixel strip
DMX digital light tube
DMX512constant voltage LED decoder
RGB/RGBW/RGB+CCTLEDstrip
DMX512-SPIdecoder
RGB/RGBW/RGB+CCTLED pixelstrip
Note: 1. Theabovedistanceismeasuredinspacious(noobstacle)environment, Pleaserefertotheactualtestdistancebeforeinstallation. 2. PleasecheckiftheWiFi routernetin2.4Gband, the5Gband isnotavailable, and donothideyourrouternetwork. 3. PleasekeepthedistancebetweenWT-DMX-M devicesandrouterclose, andchecktheWiFisignals. 4. WiFi signal strength detection: open the main interface of social security, click enter the device interface,
click “check device network” for testing.
Wiring Diagram
1. WT-DMX-M connect with DMX512 spot light
AC100-240V
Power Supply 12-36VDC
Constant Voltage
Push switch 1 (ON/OFF button)
INPUT 5-24VDC
RUN MATCH/SET
WT-DMX-M
DMX OUTPUT PUSH INPUT D+ D- GND P2 GND P1
Push switch 2 (Dynamic mode button)
DMX spot light DMX signal
VB A V+
2. WT-DMX-M connect with DMX512 pixel strip
AC100-240V
Power Supply 12-36VDC
Constant Voltage
Push switch 1 (ON/OFF button)
DMX OUTPUT PUSH INPUT D+ D- GND P2 GND P1
INPUT 5-24VDC
WT-DMX-M
RUN MATCH/SET
VB A V+
Push switch 2 (Dynamic mode button) DMX digital light strip DMX signal
Page 1-2
3. WT-DMX-M connect with DMX512 Digital light tube
AC100-240V
Power Supply 12-36VDC
Constant Voltage
Push switch 1 (ON/OFF button)
INPUT 5-24VDC
RUN MATCH/SET
WT-DMX-M
DMX OUTPUT PUSH INPUT D+ D- GND P2 GND P1
Push switch 2 (Dynamic mode button)
DMX signal
VB A DMX digital light tube V+
DMX digital light tube
4. WT-DMX-M connect with multiple DMX512 constant voltage decoder (Connecting multiple four-channel constant voltage DMX512 decoders to control multiple RGBW LED strips as an example)
AC100-240V
L N
Power Supply 12-36VDC
Constant Voltage
INPUT 5-24VDC
RUN MATCH/SET
WT-DMX-M
DMX signal
DMX OUTPUT PUSH INPUT D+ D- GND P2 GND P1
Push switch 1 (ON/OFF button)
Push switch 2 (Dynamic mode button)
V-
V+ DA
5. WT-DMX-M connect with one or multiple DMX512-SPI decoder (Connecting multiple DMX512 to SPI decoders to control multiple pixel RGB/RGBW LED strips as an example)
AC100-240V
Power Supply 12-36VDC
Constant Voltage
INPUT 5-24VDC
RUN MATCH/SET
WT-DMX-M
DMXsignal
DMX OUTPUT PUSH INPUT D+ D- GND P2 GND P1
Push switch 1 (ON/OFF button)
Push switch 2 (Dynamic mode button)
D+
D-
GND
D+
D-
GND
DMX OUT
DMX IN
DMX OUT
DMX IN
DMX OUT
DMX IN
Power Supply 5-24VDC
Constant Voltage
D+
D-
GND
D+
D-
GND
Power Supply 5-24VDC
Constant Voltage
D+
D-
GND
D+
D-
GND
Power Supply 5-24VDC
Constant Voltage
DS-L
M
INPUT 5-24VDC
SPI SIGNAL OUTPUT
CLK2 DATA2 CLK1 DATA1 VVV+ V+
DS-L
M
INPUT 5-24VDC
SPI SIGNAL OUTPUT
CLK2 DATA2 CLK1 DATA1 VVV+ V+
DS-L
M
INPUT 5-24VDC
SPI SIGNAL OUTPUT
Note 1. Separate power supplies are required for the DMX512 master and DMX512 decoder. 2.The DMX512-SPI decoder’s decode first addressare all set to 001.
CLK2 DATA2 CLK1 DATA1 VVV+ V+
V+
DA RGB/RGBW LED pixelstrip
V-
RGB/RGBW
V+
DA RGB/RGBW LED pixelstrip
V-
LED
D
D
GND
GND
D
D
DMX in/out DMX in/out
DMX in/out DMX in/out
DMX in/out DMX in/out
pixelstrip
M
Power Supply 12-48VDC
Constant Voltage
D
D
GND
GND
D
D
M
Power Supply
12-48VDC
Constant Voltage
D
D
GND
GND
D
D
M
Power Supply 12-48VDC
Constant Voltage
D4-P
IN PUT 12-48VDC
OUTPUT 1 2 34
WW CW WW CW RG BW
D4-P
IN PUT 12-48VDC
OUTPUT 1 2 34
WW CW WW CW RG BW
D4-P
IN PUT 12-48VDC
OUTPUT 1 2 34
WW CW WW CW RG BW
W
RGBW LED strip
+ + +
W
RGBW LED strip
+ + +
W RGBW LED strip
+ + +
Note 1. Separate power supplies are required for the DMX512 master and DMX512 decoder. 2.The decode first address sequence of DMX512 constant voltage LED decoder is set as follows 509, …., 009, 005, 001,
address interval 4. 3.The WT-DMX-M master uses 8-bit gray scale output.
Note that set the DMX512 decoder to 8-bit decode mode. 4. An DMX signal amplifier is needed if more than 32 DMX512 decoders are connected,
or use overlong signal line, signal amplification should not be more than 5 times continuously. 5. If the recoil effect occurs because of longer signal line or bad line quality,
please try to connect 0.25W 90-120 terminal resistor at the end of each DMX signal line.
User Manual Ver 1.0.1 2025.7
Push Switch Function
Use the push switch 1 to turn the light on/off or adjust the brightness. Push switch 1 (ON/OFF Button) Short press: Turnon/offthelight. Long press (1-10s): Brightness increases or decreases continuously.
Each time you release and then long press again, the brightness changes in the opposite direction. Increasing or decreasing the brightness by 1 level every 2s, a total of 5 levels of brightness(20%, 40%, 60%, 80%, 100%).
Push switch 2 (Dynamic Mode Button) Use the push switch 2 to switch the dynamic mode change type, direction and speed, and the dynamic mode color is xed to seven colors (red, yellow, green, cyan, blue, purple and white). Short press: Switch the change type of dynamic mode in sequence, 9 types in total ( ow, chase, block, oat, trail, trail + black, jump, smooth, chaotic ash). Double-click: Switch the motion direction (forward or reverse) of the dynamic mode. Jump, smooth, chaotic ash dynamic mode do not support the motion direction setting. Longpress(1-10s): Speed increases or decreases continuously.
Each time you release and then long press again, the speed changes in the opposite direction. Increasing or decreasing the speed by 1 level every 2s, a total of 5 levels of speed.
Page 3-4
Light Type Setting
Long press the Match/set key for 2s, sequential switching of three light types (RGB, RGBW, RGB+CCT), and the RUN indicator changes to the corresponding color (red: RGB, green: RGBW, blue: RGB+CCT). Long press the Match/set key for 15s to restore factory defaults. factory default RGB light type, R/G/B color sequence, output 510 channels. If Tuya Smart APP network connection succeed, you can also set light type through the APP.
The channel address correspondence of each pixel point for different light types is as follows:
RGB
RGBW
RGB+CCT
Pixel R G B Pixel R G B W Pixel R G B WW CW
1 12 3
1 1 2 3 4
1
1 2 3 4
5
2 45 6
2 5 6 7 8
2
6 7 8 9 10
3 78 9
3 9 10 11 12 3 11 12 13 14 15
··· ··· ··· ···
··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ···
170 508 509 510 128 509 510 511 512 102 506 507 508 509 510
Note: When RGBW and RGB+CCT light type, no matter APP interface, push switch or RF remote control operation, when changing the dynamic mode effect, it only changes the R/G/B channel output, i.e., W channel and WW/CW channel are not involved in the dynamic effect output.
Tuya Smart APP Network Connection and Operation Interface
Push twice Match key fastly, or press and hold Match key for 5s, clear previous network connection, enter WiFi config mode, LED indicator flash fastly. If Tuya Smart APP network connection succeed, the RUN LED indicator will stop flash, and in Tuya Smart APP, you can find WT-DMX-Master device. You can set the number of channels, light type, and R/G/B color sequence through the APP setting interface.
When controlling the light with Tuya Smart/Smart Life APP, if the network connection is poor, you can control the light with Bluetooth connection within the Bluetooth control range. Note: The light can not be directly controlled by Bluetooth without WiFi configuration.
Channel Number
Channel Number
0.24
Other interface For the first time use, set channel number, light type and color sequence.
User Manual Ver 1.0.1 2025.7
Channel number interface According to requirements select number of channels, channel number range:24-512.
Light type interface Select RGB, RGBW, RGBCCT light type.
Lights with color sequence interface Select the corresponding R/G/B/W sequence according to the color sequence of the light. (RGB, RBG, GRB, GBR, BRG, BGR,RGBW, RBGW, GRBW, GBRW, BRGW,BGRW, WRGB,WRBG, WGRB, WGBR, WBRG, WBGR)
Plan interface Countdown: Customize the countdown time (Max.24 hours) to perform the on/off action. Timer: Customize multiple times to perform the on/off light action.
Colour: Touch the color rectangle to adjust color and saturation. Touch the brightness slide to adjust brightness.
White: Touch the color rectangle to adjust color temperature. Touch the brightness slide to adjust brightness. RGB or RGBW light types Use R/G/B mixing to simulate color temperature.
ColorCard: Touch the color card array to select many different colors. Touch the brightness slide to adjust brightness.
Combination: Select a proportional distribution of multi-color circle, evenly distribute these colors on the LED strip.
Color Fill: Change the color of the full segment of the LED strip.
Color pen: change the color of a single segment of the LED strip.
Eraser: Erase the color of a single segment of the LED strip, i.e., turn off the light. Color transition: When there are multiple colors in the LED strip, you can set to turn on or off the color segment gradient transition.
Page 5-6
Scene interface 44 predefined scenarios and 10+ custom dynamic scenarios selectable. The custom scenarios can select 16 types variations (fade, jump, breath, flash, flow, rainbow, shooting star, pile-up, floating down, chasing light, floating, flashing, bouncing, shuttle, chaotic flashing, open and close), the 1-8 colors, full or segment control, forward or reverse motion direction, adjustable brightness and speed.
Music rhythm interface 6 local music modes (rock, jazz, classical, rolling, energy, spectrum) selectable. 3 APP modes (music rhythm, game, romance) selectable. Adjustable sensitivity of the received sound. The light follows the rhythm according to the music collected by the phone microphone. Note: the DMX512 master only supports APP mode.
RF Remote Control
The DMX512 master can be matched with optional R9 remote control, then through the remote control to switch static or dynamic mode, set the R/G/B color sequence and the number of output channels.
Remote control match and deletion method: Match: Short press match key, immediately press on/off key of the remote. Delete: Press and hold match key for 10s to delete all match, LED indicator flash fastly means all matched remotes were deleted.
R9 remote control set R/G/B color sequence and number of output channels: 1. The DMX signal default to the RGB color order. If the RGB color is not correct,
you can change the R/G/B color order by pressing 3 buttons (* + 1 digit + *): *1*RGB,*2*RBG,*3*GRB,*4*GBR,*5*BRG,*6*BGR. 2. DMX signal output default 512 channels, you can set the number of channels (024-512) by pressing five buttons (* + 3 digits + *) consecutively, e.g.: *060* to set 60 channel outputs.
R9 remote control calls up dynamic modes list:
No. P01 P02 P03 P04 P05 P06 P07 P08 P09 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20
Name
Red horse race white ground Green horse race white ground Blue horse race white ground Yellow horse race blue ground Cyan horse race blue ground Purple horse race blue ground 7 color multi horse race 7 color horse race close + open 7 color multi horse race close + open 7 color scan close + open 7 color multi-scan close + open Blue White chase Green Cyan chase RGB chase 7 color chase Blue meteor Purple meteor White meteor 7 color meteor Red oat
No.
Name
P21
Green oat
P22
Blue oat
P23
Purple oat
P24
RGBW oat
P25
Red Yellow oat
P26
Green Cyan oat
P27
Blue Purple oat
P28
Blue White oat
P29
6 color oat
P30
6 color smooth sectionally
P31
7 color jump sectionally
P32
7 color strobe sectionally
P33
White horse race (RGB jump)
P34
White smooth horse race (RGB smooth)
P35
White starlight (RGB random jump)
P36
White smooth starlight (RGB random smooth)
P37
White ow,forward
P38
White ow,forward on +backward off
P39
White ow,forward on +backward on
P40
White oat,forward
Note: P33-P40 dynamic modes are applicable to DMX type white light strip. P33-P36 dynamic modes, if the color DMX strip is connected, the corresponding color effect will appear.
User Manual Ver 1.0.1 2025.7
Page 7-8
Documents / Resources
 |
Skydance WT-DMX-M Lighting Control System [pdf] Owner's Manual WT-DMX-M Lighting Control System, WT-DMX-M, Lighting Control System, Control System, System |