WiFi CampPro 2 Long Range WiFi Repeater Kit
User Manual
NEED HELP?
 |
SignalBooster.com |
 |
855.846.2654 |
Interdiction
The WiFi CampPro 2 is the new innovative solution for WiFi Hotspot extension. It will help to you to extend WiFi Hotspot internet connection to your multiple devices such as pads, smartphones, and laptops.
Hardware Contents
Hardware Installation
Note: Please connect USB cable with Indoor device and outdoor USB device before plug-in power adapter
Configuration
Follow the below easy setup steps to set up your WiFi CampPro 2
- Login Page
When first-time setup your WiFi CampPro 2, you must set up your own password ( for security reasons can not allow below 8 characters) to access the setup
- After you set up your own password, click the “ Submit” button to go to the setup page ( it will be the required password for future setup)
- When your WiFi CampPro 2 hardware installs properly, you should see below network discovery page.
Note: if you don’t see this page, please go to the troubleshooting section at the last section of the user manual
- Pick up the Hotspot AP you wish to connect to and click the “Select” button
- ① Type in Hotspot Password if required by your selected Hotspot
② Also, required to set up your own WiFi CampPro 2 Wireless Password for the device to wireless connect your WiFi CampPro 2
Note: ③ If Hotspot has many same Name APs and you want to Lock to a specified Hotspot AP, you can select the Lock Hotspot MAC button to lock the AP
- After filling in all required information, then click the “ Finish” button
- The WiFi CampPro 2 will reboot after finished setup
Note: Please reconnect your WiFi with the correct SSID and Network Password
- After successful setup, you will see a status page with green “Connected” information
- Easy Setup
• Hotspot Name: By clicking the
scan and selecting the name of the Hotspot AP to connect.
• Lock Hotspot MAC: When clicking
Only the MAC of this Hotspot AP allows accessing the internet
• Encryption: It shows automatically when the Hotspot SSID was scanned
Here are the supported Encryptions
• Hotspot Password: Just type the Hotspot password to connect the Hotspot.
• Network Type: 5 Types of Hotspot networks are supported Static (Fixed), Dynamic(DHCP), L2TP,PPPoE and PPTP
• Hostname: WiFiCampPro2 is the default hostname or name another for your own preference.
• DNS server: You can Manual add another DNS server list or by Auto - Status:
• 
The Hotspot was successfully connected to your WiFiCampPro2
•
Now you can get the IP address from the Hotspot DHCP Server, RSSI readings, and other info.
•
Your local WiFi Network info. - HotSpot Settings
• It contains a history of the Profiles that were saved from the previous Hotspot connection. You can Enable, Edit
, Delete
or Add
to each profile.
•
Inside the profile you can set up HotSpot MAC, Password/Passkey, Type of Network, IP address, Netmask, Gateway, and DNS Server list.
Note: if you have changed any configuration, please click Apply to save the setting. - Local Network
• Wired Network
• Wired Network Configuration: You can set Static Address or DHCP Client to log on to your CampPro2 Webpage setting menu.
Note: The default IP address is 192.168.36.1
• DHCP Server: If Enable. You can set the Start IP address, Limit the number, and Lease the time of subscribers.
Note: Force enables DHCP on this network even if another server is detected. Or Disable it.
Wireless 2.4G 
- Wireless Basic Configuration: Radio On/Off, HT Mode(None HT, HT20,HT40 Auto) , Channel selection, Transmit Power (0 to 23 dBm) and Use ISO/IEC 3166 alpha2 Country codes (00 World – W Zimbabwe)
- Wireless AP Mode Configuration: SSID, MAC Address Filter, Hide SSID, and WMM mode. The Encryptions support as follow
DHCP and DNS
- Active DHCP Leases: Current active client users list. It shows the name, IP, MAC, and lease time remaining.
- Active DHCPv6 Leases: No Active IPv6 User lease.
- Static Leases: You can add or delete Static leases.
Tools: Some Network Utilities for testing Internet status.
- Ping: IPv4
- Traceroute: IPv4
- Nslookup:
System
- System Time
- System Properties: You can set the Time Zone and Sync with the browser.
- Time Synchronization: Enable NTP Client and Server.
Add or delete NTP server candidates.
Administration:
- Login Password: Change your login password.
- SSH Access: Setting listening Port. Allow login from the Internet. (Remote hosts to connect to local SSH forwarded)
System Maintenance:
System Configuration: Restore to factory default. Export or import system configuration.
The restore to default procedure will take about 180 seconds to erase the configuration partition and reboot. 
After rebooting login 192.168.36.1 and set up the new password again for later Webpage access. 
Select the exported file and import the configuration.
The pre-saved configuration will be back after the system reboot.
- Firmware Upgrade. Select the firmware file and upgrade it. You can either keep the current configuration or the default setting. It takes about 240 seconds for the system to flash.
Note: You don’t have to remove the USB WLAN Adapter while upgrading firmware. - System Reboot: Take about 180 seconds to reboot.
It wills lost LAN connection when the system is rebooting.
Logout
It shows the Login required and clicks Login to continue. 
After Login it shows the whole WiFiCampPro2 Status.
Troubleshooting:
If you see the below screen information, Please insert the ALFA USB WLAN adapter on the USB port before powering on your WifiCampPro2. Otherwise, the webpage will show USB devices not found. 
855.846.2654 | order@signalbooster.com
Documents / Resources
 |
SIGNAL BOOSTERS WiFi CampPro 2 Long Range WiFi Repeater Kit [pdf] User Manual WiFi CampPro 2, Long Range WiFi Repeater Kit, WiFi CampPro 2 Long Range WiFi Repeater Kit |
