Shenzhen Inateck Technology KB02011 Detachable Keyboard with Flexible Kickstand product 
Product Overview
How to pair an iPad
Step 1: Install iPad onto The Bluetooth keyboard
Step 2: Toggle the power switch to ON, and the Bluetooth keyboard starts.
Step 3: Press the 
simultaneously. Indicator 2 will flash in blue, which means the keyboard is under Bluetooth pairin ode. g + m
Step 4: On the iPad, select Settings- Bluetooth· On.
Step 5: The iPad will display ‘lnateck KB02011’ as an available device.
Step 6: Select “lnateck KB02011 • on the iPad.
Step 7: Indicator 2 goes off, which means the keyboard has been paired with iPad successfully.
Note
- After one successful pairing, the Bluetooth keyboard and the iPad can be automatically paired in future. However, when interference exists or unstable Bl uetooth signal on the iPad, the automatic parsing might fail. In that case, please do as following.
- Delete all Bluetooth pairing record related to KB0201 l on your iPad
- Turn off Bluetooth on iPad
- Follow ‘How to pair an iPad’ to connect.
- If iPad reminds: Connection Unsuccessful, Make sure ‘lnateck KB02011’ is turned on and in range. Please follow the steps below to reconnect.
- Delete all Bluetooth pairing record related to KB02011 on your iPad
- Turn off Bluetooth on iPad
- Follow ‘How to pair an IPad’ to connect.
Function Keys
Some shortcut Keys are listed below.
Note
- Press and hold the command key to see shortcuts in any app that supports them.
- If you want to use Caps Lock Key In normal to switch the case of alpha Characters, please follow the steps to change the iPad settings.
Find General-Keyboard-Hardware Keyboard: TURN OFF Caps Lock and Switch to/from Latin - Double click might generate full stop punctuation on iPad. If you encounter such condition while typing Space key, please follow the steps below to change the iPad settings.
Find General-Keyboard-Hardware Keyboard: TU RN OFF “• Shortcut
How to check battery status
Press
simultaneously, and judge the battery level by the nash times or lndicator 3.
Note
Indicator 3 keeps red when the keyboard is being recharged At this moment there is no way to check the battery level
Recharging
When the battery is low, indicator will flash in red. If all indicators are off, it means the battery is completely drained. Under both situations, the keyboard should be recharged. The required voltage for charging is SV with current under 250mA. A current control chip is set inside the keyboard for overcurrent protection. You can recharge the keyboard by using an ordinary phone charger or on the USB port of a computer that regularly outputs voltage at SV. The keyboard can be fully recharged in approximately 3-4 hours. Indicator keeps red when the keyboard is being recharged. The battery indicator will turn green when the keyboard is fully recharged.
Note You can use the keyboard while it is being recharged.
Sleeping mode
The keyboard will sleep automatically if there is no operation on it for 30 minutes. Wake it up by pressing any button. Under sleep mode. Blue1001h will disconnect automatically, and you can build reconnection by pressing any key.
Product Specifications
Packing list
1<802011’1
Micro-B Charging Cable*l
User Manual*l
Assembly Manual of the Keyboard*l
FAQs
When iPad alerts: Connection Unsuccessful Make sure ‘lnateck KB02011’ is turned on and in range.
Please follow the steps below to reconnect.
- Delete all Bluelooth pairing record related Lo K802011 on your iPad;
- Turn off Bluetooth on iPad;
- Follow ‘How to pair an IPad1 to reconnect.
Documents / Resources
 |
Shenzhen Inateck Technology KB02011 Detachable Keyboard with Flexible Kickstand [pdf] User Manual KB02011, 2A2T9-KB02011, 2A2T9KB02011, KB02011 Detachable Keyboard with Flexible Kickstand, KB02011, Detachable Keyboard with Flexible Kickstand, Detachable Keyboard, Keyboard |
