SEGWAY ROBOTICS CFI-ZCT1NA AMR Development Robot
Product Information
Specifications
- Product Name: Nova Carter AMR Development Robot
- Configuration: 3D Mapping Top Module Pre-installed
- Controller Model: CFI-ZCT1NA
- Certifications: CB/CE-safety, UL2271 EU Battery Directive, RoHS/REACH/PoPs, IEC/EN 62133-2:2017, UL2271, 2013/56/EC, UN38.3, S/SG/AC.10/11, Article 38.3, SDS/MSDS EMC, GOST-R, ECE R10
Product Usage Instructions
Getting Started with Nova Carter
- Step 1: Remove the Lidar Cover
Remove the screws holding the LIDAR cover in place using the included 2.5 mm, hex driver. Reinstall the screws once the cover is removed. - Step 2: Connect Monitor, Keyboard, and Mouse
Connect peripherals to the rear IO panel. You may use the provided USB-C to USB-A dongle for convenience. - Step 3: Power On
Hold the power button to turn the robot on. - Step 4: Start Using Jetson
Begin developing your robot using the familiar NVIDIA Jetson AGX OrinTM Linux environment. Default Username: nvidia Password: nvidia
Emergency Stop Use
- Press the Emergency Stop (E-Stop) button to immediately cut motor power.
- The front indicator light will blink red while the EStop is engaged. To release the E-Stop, twist the button clockwise.
Charging the Robot
- To charge Nova Carter, connect the included wall charger to the charge port.
- The charger may be used while the robot is on or off. Nova Carter will not respond to movement commands while charging.
FAQ
- Q: Where can I find more information about Nova Carter?
- A: You can scan the QR code or visit the link provided for more information: https://robotics.segway.com/download/
Getting Started with Nova Carter
Step 1: Remove the Lidar Cover
- Remove screws holding the LIDAR cover in place using included 2.5 mm hex driver. Reinstall the screws once the cover is removed.
Step 2: Connect Monitor, Keyboard, and Mouse
- Connect peripherals to the rear IO panel. You may use the provided USB-C to USB-A dongle for convenience.
Step 3: Power On
- Hold the power button to turn the robot on.
Step 4: Start Using Jetson
- Begin developing your robot using the familiar NVIDIA Jetson AGX Orin™ Linux environment.
- Default Username: nvidia
- Password: nvidia
Emergency Stop Use
- Press the Emergency Stop (E-Stop) button to immediately cut motor power. The front indicator light will blink red while the EStop is engaged. To release the E-Stop, twist the button clockwise
Charging the Robot
- To charge Nova Carter, connect the included wall charger to the charge port. The charger may be used while the robot is on or off.
- Nova Carter will not respond to movement commands while charging.
Packing Contents
Product Overview
Certifications
| Item | Standard | Qualified or not | Certification report or not |
| CB/CE-safety | IEC/EN 62133-2: 2017 | Qualified | Yes |
| UL2271 | UL2271 (sent from UL) | Qualified | Yes |
| EU Battery Directive | 2013/56/EC | Qualified | Yes |
| RoHS/REACH/PoPs | Qualified | Yes | |
| UN38.3 | S/SG/AC.10/11, Article 38.3, Dangerous Goods Transport Simulation Test of United Nations | Qualified | Yes |
| SDS/MSDS | / | Qualified | Yes |
| EMC | ECE R10 | Qualified | No |
| GOST-R | / | Qualified | Yes |
Note: The standards mentioned above are about battery certification.
More Information
- Please scan the QR code or visit the link below for more information about Nova Carter. https://robotics.segway.com/download/
CONTACT
- Distributed by Segway Robotics Inc.
- Manufactured by Ninebot Commercial (Beijing) Technology Co. LTD
- Address: 98 Spit Brook Rd. #2203, Nashua, 03062, NH, USA
- Service: support@robotics.segway.com
Documents / Resources
 |
SEGWAY ROBOTICS CFI-ZCT1NA AMR Development Robot [pdf] User Guide CFI-ZCT1NA AMR Development Robot, CFI-ZCT1NA, AMR Development Robot, Development Robot, Robot |