WT-10 Ultra Low Latency Wireless Systems
“
Specifications
- Model: WT-10 / DH-10
- Power Source: 2 x AA alkaline batteries (not included)
- Connection: USB-C cable for DH-10
- Compatibility: Works with electronic musical instruments and
computers
Product Usage Instructions
WT-10 Panel Descriptions
- PAD1/PAD2 jacks: Connect drum pads or cymbal pads using the
included cables. - Slit for belt: Attach the WT-10 to your pad using a belt with
fasteners. - Battery housing: Insert two AA alkaline batteries into the back
of the unit.
DH-10 Panel Descriptions
- USB port: Connect to a computer or electronic musical
instrument with a USB Digital Trigger INPUT port using the provided
USB-C cable. - MIDI OUT connector: Use a TRS-MIDI cable to transmit MIDI
signals to an instrument with a MIDI IN connector. - Indicator lights: Red light indicates power, blue light blinks
when receiving signals or connected via USB.
Setup Instructions
- Insert two AA alkaline batteries into the WT-10.
- Attach the clamp to the WT-10 as needed for mounting.
FAQ
What should I do if items are missing from the package?
If any included items are missing, contact the dealer where you
purchased the product for assistance.
Can I use rechargeable batteries with the unit?
No, only use non-rechargeable AA alkaline batteries with this
unit.
How should I affix the WT-10 to my pad?
Pass a belt through the slits on the unit and fasten it securely
to your pad.
What do the indicator lights signify on the DH-10?
The red light indicates power, while the blue light blinks when
receiving signals or when connected to a device via USB.
“`
WT-10 / DH-10
Owner’s Manual
Overview
¹ The WT-10 and DH-10 are ultra low-latency wireless systems that operate on Roland’s proprietary transmission/reception algorithms. ¹ With the WT-10 or DH-10, you can wirelessly connect your pads to your drum sound module or computer, without the trouble of messing around with cables.
WT-10 DH-10
Receives signals from the pads and transmits them wirelessly as performance data. You can connect up to two pads to the WT-10.
Receives wireless performance data and converts this into MIDI signals, which are transmitted to your electronic musical instrument or computer.
¹ This transmits the setting data (trigger and MIDI settings) from your electronic musical instrument or computer to the WT-10. The settings are saved on the DH-10.
¹ You can use a USB cable to connect the unit to your computer or to an electronic musical instrument, or transmit MIDI signals to your instrument via the MIDI OUT connector.
Checking what’s included
Once you’ve opened the package, make sure that nothing is missing. If any of the included items are missing, consult with the dealer from which you purchased this product.
WT-10
DH-10
¹ WT-10 ¹ Clamp ¹ Two connection cables (0.4 m) ¹ Owner’s Manual (this document) * Batteries are not included.
¹ DH-10 ¹ Clamp ¹ USB-C cable (0.5 m) ¹ USB-C to A adaptor ¹ Owner’s Manual (this document)
Panel descriptions
WT-10
PAD1/PAD2 jacks
Use the included connection cables to connect these jacks to your drum pads, cymbal pads and so on.
* The power turns on when you insert a plug into the PAD1 jack. * When connecting only one pad, use the PAD1 jack. * When connecting the Roland VH-10 hi-hat or CY-16R-T cymbal, use
both jacks.
PAD1
PAD2
VH-10
HI-HAT plug
HH CONTROL plug
CY-16R-T RIDE plug
BELL plug
Slit for belt
Pass a belt with fasteners (commercially available) on either end through the slits to affix the WT-10 to your pad.
DH-10
USB port
Use the included USB-C cable to connect this unit to your computer or to an electronic musical instrument that has a USB Digital Trigger INPUT port. * Do not use a USB cable that is designed only for charging a device.
Charge-only cables cannot transmit data.
MIDI OUT connector
Use a commercially available TRS-MIDI cable to transmit MIDI signals to an electronic musical instrument that has a MIDI IN connector.
Clamp
This can be used to attach the unit to a stand or similar gear. Insert the clamp into the groove on the back of the WT-10. You can attach the unit in any of four directions. * When you operate the clamp, please be careful not to get
your fingers pinched between the movable part and the panel. In places where small children are present, make sure that an adult provides supervision and guidance.
Indicator (blue)
Lights up when the power is on and when a pad is struck.
Battery housing (back of unit)
Insert two alkaline batteries (AA, LR6). * Batteries are not included with this unit. * Rechargeable batteries cannot be used. * If you handle batteries improperly, you risk explosion
and fluid leakage. Make sure that you carefully observe all of the items related to batteries that are listed in the leaflet “USING THE UNIT SAFELY” and “IMPORTANT NOTES”.
Clamp
This can be used to attach the unit to a stand or similar gear. Insert the clamp into the groove on the back of the DH-10. You can attach the unit in any of four directions.
Indicator (red)
This lights up red when the power is on. The indicator blinks when a signal is received from a pad.
Indicator (blue)
When the unit is connected to an electronic musical instrument or computer via USB, this blinks until the connected device is recognized, and stays lit afterwards.
Before using this unit, carefully read the leaflet “USING THE UNIT SAFELY” and “IMPORTANT NOTES”. After reading, keep the document(s) where it will be available for immediate reference.
English ©2024 Roland Corporation
Setup
DH-10
WT-10
1. Insert two alkaline batteries (AA, LR6) into the WT-10.
2. Attach the clamp to the WT-10 as necessary.
3. Connect the cables to the PAD1/PAD2 jacks.
The power turns on when you insert a plug into the PAD1 jack (the indicator briefly lights up blue). * When connecting only one drum pad, use the PAD1 jack. * When connecting the Roland VH-10 hi-hat or CY-16R-T cymbal, use both jacks.
4. Configure the pad triggers.
Configure the triggers on the computer or electronic musical instrument to which the DH-10 is connected via USB. See the “DWe Control Setting Guide” (Roland website) for details on how to configure the triggers.
5. Attach the WT-10 onto the stand or pad.
To attach this unit to a stand or pad with the clamp, use these steps: (1) loosen the clamp screw Ó (2) fasten the clamp onto the stand or drum hoop Ó (3) tighten the screw to lock the clamp in place.
Example 1: Use the clamp to attach the unit to a hi-hat stand
Example 2: Use the clamp to use this unit with a drum or drum trigger
Mounted onto a bass Attached to a snare hoop Mounted onto a hoop
drum hoop
(RT-30, WT-10, BT-1)
with rubber rim
Example 3: Mount the unit onto a drum stand with a commercially available hook-and-loop fastener belt
1. Attach the clamp to the DH-10 as necessary.
2. Attach the DH-10 to your electronic musical instrument or
stand near the computer.
Use the included USB-C cable and USB-C to A adaptor, or a commercially available TRS-MIDI cable, according to the shape of the jack or connector you’re connecting to. Example: Attaching to an SPD-SX PRO
Main specifications
Wireless Format Wireless Carrier Frequency Transmission Range Connectors Power Supply Battery Life
Dimensions
Weight Clamp Mountable Diameter Size Accessories
WT-10 Original wireless transfer method
DH-10
2.4 GHz
10 m (32 feet) line-of-sight * May vary due to local conditions
Trigger input jacks (PAD1, PAD2)
USB Port: USB Type-C
MIDI OUT connector: TRS mini jack
Alkaline battery (AA, LR6) x 2
Supplied from via USB
Approx. 6 months
* This can vary depending
on the conditions of use.
Body: 70 (W) x 31 (D) x 98 (H) mm 2-13/16 (W) x 1-1/4 (D) x 3-7/8 (H) inches
Body:
70 (W) x 45 (D) x 58 (H) mm 2-13/16 (W) x 1-13/16 (D) x 2-5/16 (H) inches
Includes horizontal clamp: 84 (W) x 73 (D) x 98 (H) mm 3-5/16 (W) x 2-7/8 (D) x 3-7/8 (H) inches
Includes horizontal clamp:
84 (W) 88 (D) x 58 (H) mm 3-5/16 (W) x 3-1/2 (D) x 2-5/16 (H) inches
170 g / 6 oz (including batteries)
65 g / 3 oz
225 g / 8 oz (including batteries and clamp)
120 g / 5 oz (including clamp)
4.5 mm 32 mm
3/16 inches 1-5/16 inches
Clamp, Connection cables (0.4 m / 15 inches) x 2, Owner’s Manual, Leaflet “USING THE UNIT SAFELY”
Clamp, USB-C cable (0.5 m / 19 inches), USB C to A adaptor, Owner’s Manual, Leaflet “USING THE UNIT SAFELY”
Example 4: Use a 1/4-inch nut to mount the unit onto a camera tripod
* This document explains the specifications of the product at the time that the document was issued. For the latest information, refer to the Roland website.
Documents / Resources
 |
Roland WT-10 Ultra Low Latency Wireless Systems [pdf] Owner's Manual WT-10, WT-10 Ultra Low Latency Wireless Systems, Ultra Low Latency Wireless Systems, Low Latency Wireless Systems, Latency Wireless Systems, Wireless Systems |