Ring 5AT3S2 Contact Sensor User Guide

Contents hide

1 ring 5AT3S2 Contact Sensor

2 IMPORTANT PRODUCT INFORMATION

3 SAFETY INFORMATION

4 BATTERY SAFETY

5 PRODUCT SPECIFICATIONS

6 FCC Rules

7 Documents / Resources

7.1 References

8 Related Posts

ring 5AT3S2 Contact Sensor

IMPORTANT PRODUCT INFORMATION

Safety and Compliance Information Use Responsibly. Read all instructions and safety information before use.

SAFETY INFORMATION

FAILURE TO FOU.OW THESE SAFETY l,D INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE.

BATTERY SAFETY

This product contains lithium coin batteries. L,D This device requires batteries for use. Only use new CR2032 3V batteries. Never mix old and new batteries. Keep all of the batteries out of the reach of children. Do not open, disassemble, puncture, cut, bend, shred or heat the batteries and do not allow metal objects to touch the battery terminals on the remote as they can become hot and cause burns. Remove all batteries if they are worn out or before storing your Device for an extended period of time. Dispose of all batteries in accordance with applicable laws and regulations and do not dispose of batteries by throwing them into a fire. If any batteries begin to leak, take steps to prevent the fluid from coming into direct contact with skin or clothes as the fluid could be corrosive and may be toxic. Remove the batteries and clean the battery compartment in accordance with the battery manufacturer’s recommendations. WATCH FOR SMAU. PARTS. Your device and accessories may present a choking hazard to small children. Keep them out of reach of small children.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment should
be installed and operated with minimum distance 20 cm between the radiator & your body.
CAUTION: To reduce the risk of electrical shock, DO NOT open the unit. There are no user serviceable parts inside the unit. Refer to customer support for any repairs.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of the used batteries according to the manufacturer’s instructions.

PRODUCT SPECIFICATIONS

Electrical Rating: 2 CR2032 (3 V)
Temperature Rating: 32°F to 120″F (D°C to 49°C)

RECYCLING YOUR DEVICE PROPERLY

In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle,

your device in accordance with your local laws and regulations. For informalion aboul recycling your device, go to –.amazon.com/device support

TERMS OF SERVICE AND WARRANTY

Use of the product is subject to your registration with Ring and your agreement with the Terms of Service found at-.ring.com/terms. To reviewyour warranty coverage, please refer to the enclosure inside this box or visit-.ring.com/warranty.

FOR USERS IN THE UNITED STATES

Supplier’s Declaration of Conformity• Compliance Information Statement Unique Identifier: Contact Sensor

Model: 5AT3S2

FCC ID: 2AEUP5AT3S2

Responsible Party and Party issuing

Supplier’s Declaration of Conformity:

Ring LLC, 1523 26th Street Santa Monica, CA 90404 -.ring.com / legal@ring.com

FCC Rules

FCC Compliance Statement (for products subject toPart15)

This device complies with part 1 5 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and(2)this device must accept any interference received, Including any interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.

Connect the equipment to a socket on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Pursuant to Section 15.21 of the FCC rules, changes or modifications to a Product by the user that are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The device meets the FCC Radio Frequency Emission Guidelines. Information on the product is on file with the FCC and can be found by inputting such Product’s FCC ID (which can be found on the device) into the FCC ID Search form available at https://fccid.io.
The party responsible for FCC compliance is Ring LLC, 1523 26th Street Santa Monica, CA 90404.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated
in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement.
FOR USERS IN CANADA
Innovation, Science and Economic Development Canada (ISED) Compliance
This device contains license-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.

This device must accept any interference, including interference that may cause undesired operation of the device.

Documents / Resources

ring 5AT3S2 Contact Sensor [pdf] User Guide
5AT3S2, 2AEUP5AT3S2, 5AT3S2 Contact Sensor, Contact Sensor

References

User Manual