RICE LAKE 6756 Plus Static Dimensioning System Instruction Manual

© Rice Lake Weighing Systems. All rights reserved.
Rice Lake Weighing Systems®
is a registered trademark of Rice Lake Weighing Systems.
All other brand or product names within this publication are trademarks or registered trademarks of their respective companies.
All information contained within this publication is, to the best of our knowledge, complete and accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make changes to the technology, features, specifications and design of the equipment without notice.
The most current version of this publication, software, firmware and all other product updates can be found on our website: www.ricelake.com
Rice Lake continually offers web-based video training on a growing selection of product-related topics at no cost. Visit www.ricelake.com/webinars
Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training or obtained by calling 715-234-9171 and asking for the training department.

Introduction

This manual provides an overview of the iDimension Plus setup and operating instructions.
Ensure the iDimension Plus unit is fully assembled by following the iDimension Plus Assembly Instructions (PN 197164).
When interfacing this device with third party software, please reference the software manufacturer’s documentation for setup and configuration parameters as necessary.

Manuals are available from Rice Lake Weighing Systems at www.ricelake.com/manuals
Warranty information is available at www.ricelake.com/warranties

Additional Manual Resources

iDimension Plus Assembly Instructions (PN 197164). The iDimension Plus Assembly Instructions describe how to assemble the iDimension Plus.

iDimension Plus QubeVu Managers Guide (PN 195441). The iDimension Plus QubeVu Managers Guide provides a detailed overview of the QubeVu Manager, the embedded firmware of the iDimension Plus.

1.1 Regulatory Information
This product is a Class 1 Laser Product according to IEC 60825-1:2007 Ed. 2.0 and complies with 21 CFR 1040.1 pursuant to Laser Notice No. 50. A laser source with a diffraction optical element is embedded in the product, which produces a maximum output power of 1.1 mW at the aperture with a maximum wavelength of 825 nm.
1.2 FCC Compliance
United States
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Canada
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
1.3 OIML/EU Certification Special Notice of Use
The dimensions and/or volume shown are those of the smallest rectangular box that fully encloses the object.

1.4 Safety
Safety Definitions:

DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Includes hazards that are exposed when guards are removed.
WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death. Includes hazards that are exposed when guards are removed.
CAUTION: Indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury.
IMPORTANT: Indicates information about procedures that, if not observed, could result in damage to equipment or corruption to and loss of data.

General Safety
Do not operate or work on this equipment unless this manual has been read and all instructions are understood.
Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake Weighing Systems dealer for replacement manuals.

WARNING
Failure to heed could result in serious injury or death.

Electric shock hazard!
There are no user serviceable parts. Refer to qualified service personnel for service.
The unit has no power switch, to completely remove power from the unit, disconnect the power source at the AC outlet.
For pluggable equipment the socket outlet must be installed near the equipment and must be easily accessible.
When cycling power, use the in-line power cord at a power outlet, do not power at the base.
Always disconnect from main power before performing work on the device.
Do not allow minors (children) or inexperienced persons to operate this unit.
Do not operate without all shields and guards in place.
Do not place fingers into slots or possible pinch points.
Do not use this product if any of the components are cracked.
Do not make alterations or modifications to the unit.
Do not remove or obscure warning labels.
Do not use near water, avoid contact with excessive moisture.
Keep the unit dry.
Retain packaging. When transporting the unit, always disassemble and pack it in its original packaging.
Use only supplied power adapter. Never short-circuit the power adapter or the device.
Never remove the iDimension Plus head cover or the electrical connection panels at the base of the pole assembly.
Never modify or attempt to repair the unit. Service must be performed by Rice Lake Weighing Systems only.
Handle cables and cable connectors with care.
Never use damaged power cords, plugs or loose electrical sockets.
Never touch the power cord with wet hands.
Ensure that the base plate, pole assembly and head unit are all securely attached before attempting to move the unit.
Never lift the unit by grasping only the pole assembly.
Always ensure that both sections of the pole assembly and the base plate are supported.
Never drop or allow an impact to the head.
Mount on a flat surface.
Never use product for anything other than its intended purpose.

1.5 Installation Requirements
IMPORTANT: Avoid installation of the unit near direct sunlight or near bright lights. Direct sunlight and overhead lighting causes void pixels and noise that will affect the system from performing a dimension.
Protect the iDimension Plus from static electricity and connect to a clean AC power outlet.
Install the iDimension Plus on a table or sturdy level work surface large enough for the base plate and scale. Ensure the location provides a large enough work surface clear from other objects in the measurement area.

1.5.1 Measuring Platform
The iDimension Plus can be installed over any platform or surface. Measuring flat items, such as envelopes and small poly bags, requires a flat, non-reflective platform. Please contact Rice Lake Weighing Systems for further information.
1.5.2 Scale Placement
If using a scale, place the scale on the base plate, centered on the marks (Figure 1-1). Secure the scale into position.
Continuous movement of the scale may provide inaccurate measurements. If the scale moves from the original position placed after a zero height or reset function, results may be inaccurate.

Setup Wizard

This section provides an overview of how to set up the iDimension Plus.
The Setup Wizard displays during initial power-up. Skip to Step 4 if Setup Wizard displays.

2.1 Access Setup Wizard
If Setup Wizard does not display, use the following steps.

From the display (Figure 3-1 on page 16), select the Device Information button . Device Info menu displays (Figure 4-1 on page 20).

Select the Configuration Menu button (Section 4.1 on page 20). Configuration Menu displays.
Select Setup Wizard.

The Initial Setup Wizard displays.
5. Select checkmark to run the initial Setup Wizard.

2.1.1 Time Zone
The Time Zone button displays the current time zone.

Use the following steps to edit the time zone.

Select Time Zone, Figure 2-5. The current time zone displays.
Scroll or to highlight the desired time zone.

Select to continue.

2.1.2 Date and Time
The Date and Time button allows the adjustment of date or time if necessary.

Use the following steps to adjust the date or time.

Select Time & Date Figure 2-2 on page 10.
Use or to enter the current time and date.
Select to continue.

2.2 Zero Height

Select the base type of the iDimension Plus.
• Flat base or smooth scale: If the base is a smooth top scale or no scale, only using the iDimension Plus base, select the and proceed to Step 3
• Scale with bumps tread or rollers: If the base has an uneven surface (roller balls or conveyor), not using the iDimension Plus base, select the then continue to Step 2
Place the calibration object on top of the scale then select .
Ensure the platform is clear of other objects then select .
NOTE: It is important to keep the scale or iDimension Plus base clear and unobstructed during the zero height calibration to set the zero height accurately.
Stand clear of the unit before the countdown completes.
The operator is advised on the platform distance that will be adjusted and asked to confirm by pressing .
Press upon successful zero height calibration.
Remove the calibration object, if used when the base has an uneven surface (roller balls or conveyor). The base is selected within Step 1 on page 12.

NOTE: If the zero height fails, ensure the dimensioning area is clear, the scale is level and repeat the zero height function.
If unable to perform a successful zero height, calibration may be required (Section 2.0 on page 10).

2.3 Scan Zone
The scan zone is the area the system uses to dimension an item. When identifying the scan zone, consider the area needs to be clear from all other objects and is used to identify motion detected by an operator placing an item on the platform. Before the unit can attempt to perform a dimension, the scan area is required to be free from motion by the operator or objects near the device.
If the application has enabled flats; items than are less than 1.2″ (3 cm) in height, the scan zone is required to be as large in length and width as the object.

Adjust the scan area by adjusting each of the four dots (touch points) on the screen Figure 2-11.
Select when scan zone is configured.

2.4 Certified Settings

Select or to select the appropriate configuration profile.
NOTE: The default configuration is US (48”). Selecting –Current Settings– leaves this unchanged.
Please contact Rice Lake Weighing Systems Support for advice on profile selection.
The profile will depend on the hardware configuration and Legal for Trade requirements and was selected during the initial setup wizard. See Table 2-1 on page 15 for detailed information on each profile.

Select

when the desired certified setting is selected.

Profile Name	Use If
Metric (1.2 m)	Measurement unit Scan head mount height Minimum object height Legal for Trade application	= Metric = 1.2 m > 3 cm No
Metric (1.2 m with glass platter)	Measurement unit Scan head mount height Scale with glass platter Legal for Trade application	= Metric = 1.2 m Yes No
Metric (1.2 m with rgb camera)	Measurement unit Scan head mount height Minimum object height Legal for Trade application	= Metric = 1.2 m < 3 cm No
Metric (1.5 m)	Measurement unit Scan head mount height Minimum object height Legal for Trade application	= Metric = 1.5 m > 3 cm No
Metric (1.5 m with glass platter)	Measurement unit Scan head mount height Scale with glass platter Legal for Trade application	= Metric = 1.5 m Yes No
Metric (1.5 m with rgb camera)	Measurement unit Scan head mount height Minimum object height Legal for Trade application	= Metric = 1.5 m < 3 cm No
Metric (2.0 m)	Measurement unit Scan head mount height Minimum object height Legal for Trade application	= Metric = 2.0 m > 10 cm No
Certified – MID: T1108 (1.2 m)	Measurement unit Scan head mount height Legal for Trade application	= Metric = 1.2 m Yes (MID
Certified – MID: T1108 (1.5 m)	Measurement unit Scan head mount height Legal for Trade application	= Metric = 1.5 m Yes (MID)
Certified – MID: T1108 (2.0 m)	Measurement unit Scan head mount height Legal for Trade application	= Metric = 2.0 m Yes (MID
Certified – OIML: R129/2000-NL1-A-20.05 (1.2 m)	Measurement unit Scan head mount height Legal for Trade application	= Metric = 1.2 m Yes (MID)
Certified – OIML: R129/2000-NL1-A-20.05 (1.5 m)	Measurement unit Scan head mount height Legal for Trade application	= Metric = 1.5 m Yes (OIML)
Certified – OIML: R129/2000-NL1-A-20.05 (2.0 m)	Measurement unit Scan head mount height Legal for Trade application	= Metric = 2.0 m Yes (OIML)
US (48”)	Measurement unit Scan head mount height Minimum object height Legal for Trade application	= US = 48” > 1.2” No
US (48” with glass platter)	Measurement unit Scan head mount height Scale with glass platter Legal for Trade application	= US = 48” Yes No
US (48” with rgb camera)	Measurement unit Scan head mount height Minimum object height Legal for Trade application	= US = 48” < 1.2” No
US (60”)	Measurement unit Scan head mount height Minimum object height Legal for Trade application	= US = 60” > 1.2” No
US (60” with glass platter)	Measurement unit Scan head mount height Scale with glass platter Legal for Trade application	= US = 60” Yes No
US (60” with rgb camera)	Measurement unit Scan head mount height Minimum object height Legal for Trade application	= US = 60” < 1.2” No
US (80”)	Measurement unit Scan head mount height Minimum object height Legal for Trade application	= US = 80” > 4” No

Table 2-1. Measurement Parameters
• Selecting any of the “Metric” profiles prompts for the selection of measurement unit: m, mm or cm.
RICE LAKE 6756 Plus Static Dimensioning System - Introduction 14

Select or to scroll to the desired unit of measure.
Select when the desired unit of measure is selected.
Upon completion of the setup wizard, the system restarts.

Clear the platform of obstructions to continue.

2.5 Next Steps
The Setup Wizard is now complete. Additional setup requires connection of the iDimension Plus to a PC from a network connection to access QubeVu Manager.

Connect iDimension to network (Section 6.0 on page 31).

Configure general settings (Section 7.2 on page 35).
Configure scale settings for connecting to iDimension Plus (Section 7.2.2 on page 37).
Configure network (Section 7.3 on page 38).

Touchscreen Display

This section provides an overview of iDimension Plus USB touchscreen display indicator and control instructions.
The USB touchscreen display combines the weight and dimensions from the iDimension Plus and the optional scale to be visualized.
The touchscreen display provides the dimensions, a live displayed scale weight and operator access to system level controls.

3.1 Touch Screen Display Operation
A live image provides the user feedback on the placement of the item and conditions that may cause the system to be unable to dimension, for example out of bounds. The blue line shown in Figure 3-1, indicates the scan zone defined during initial setup.
The Power button for the USB display is located on the back of the unit. The USB operator display can be configured in QubeVu Manager, see the iDimension Plus QubeVu Managers Guide (PN 195441).

The indicator provides out of bounds and shape information for dimensioning. Function keys allow the iDimension Plus to be managed via the touchscreen display.
3.1.1 Live Image
The weigh area provides a real-time view of the scanning area from the scanning head onto the USB display. The blue box within Figure 3-1 is the Scan Zone which indicates the area the iDimension Plus will dimension.

3.1.2 Out of Bounds Indication
The Out of Bounds icon indicates the object is not outside of the Scan Zone. If the object is outside of the Scan Zone, an exclamation point appears with arrows indicating the direction the object is not within the Scan Zone.
If all four of the arrows within the Out of Bounds icon are lit , the object being dimensioned is not within the viewing area or the item is too large. The arrows within the Out of Bounds icon display the direction which the item is outside of the Scan Zone.

3.1.3 Shape Indication
The Shape Indication icon indicates the shape of the object being dimensioned.

The Regular Shape icon indicates if the item is dimensioned as a regular shape and the dimensions are displayed in 0.2” or 0.5 cm increments.
The Irregular Shape icon indicates if the item is dimensioned as an irregular shape and the dimensions are displayed in 0.5” or 0.5 cm increments.

3.1.4 Status Indication
Status indicates the current status of the iDimension Plus unit.

The status indicates the device is ready to perform a dimensioning transaction
The status indicates a successful dimensioning transaction is complete
The status displays during restart or if the devices requires a restart from the Configuration menu

The status displays briefly while dimensioning or if user intervention is required; select the Help function key to see real time feedback of the system if the device displays the started, stopped or wait condition

3.1.5 Help Key
The Help function key displays the Issue Review menu.
The Help function key provides real time feedback to the operator of the unit. It provides step-by-step instructions on how to clear conditions such as start, stop, wait or remove condition with no object in the scan area.

Select the ruler icon at the bottom of the touchscreen display Figure 3-2 to return to the main screen.

3.1.6 Zero Height Key
The Zero Height function key allows the iDimension Plus to calculate the distance between the scan head and the base.
Zeroing the height after initial setup is only necessary if the distance between the scan head and the measuring platform changes.
Example: When a scale is added or removed.
To perform the Zero Height function, refer to the following steps:

Select the base type of the iDimension Plus.
• If the base is a smooth top scale or no scale, only using the iDimension Plus base, select the scale type and proceed to Step 3 on page 20
• If the base has an uneven surface (roller balls or conveyor), not using the iDimension Plus base, select the then continue to Step 2. For best performance, choose this function

Place the calibration object on top of the scale then select .
Ensure the platform is clear of other objects then select .
NOTE: It is important to keep the scale or iDimension Plus base clear and unobstructed during the zero height calibration to set the zero height accurately.
Stand clear of the unit before the countdown completes.

Upon successful zero height calibration select . The display returns to the Touchscreen Display (Figure 3-1 on page 17).
Remove the calibration object.

Configuration Menu

This section provides an overview of iDimension Plus configuration menu instructions.The Configuration Menu provides more configuration options when accessed through touchscreen display than when accessed through a PC.

4.1 Access Configuration Menu
To access the Configuration Menu, use the following steps:

Select the Device Information function key located at the bottom of the screen (Figure 3-1 on page 17).

The Device Info menu displays (Figure 4-1). For additional Device Info information (Section 4.2 on page 26).
Select the Configuration function key .
The Configuration Menu displays.

Item	Description	Reference
Setup Wizard	Steps through initial configuration to allow unit operation	Section 4.1.2 on page 22
View EULA	Displays the Software End User License Agreement information	Section 4.1.3 on page 23
Time Zone	Displays the current time zone and allows for time zone configuration	Section 4.1.4 on page 23
Date & Time	Allows the adjustment of date and time	Section 2.1.2 on page 11
Data Extract	View the configuration settings and the current and previous status; Must be configuration in administration mode	Section 4.1.4 on page 23
Scan Zone	Allows for configuration of the Zone of Interest	Section 2.3 on page 14
Restart	Select to restart the iDimension Plus unit	Section 4.1.5 on page 24
Upgrade Firmware	Allows for a connected USB drive to update the current device firmware	Section 4.1.6 on page 24
IP Address	Select to view the current IP address of the iDimension Plus unit	Section 4.1.7 on page 25

Table 4-1. Configuration Menu Keys

4.1.1 Inspection Menu Key
The Inspection Menu function key provides access to Weight and Measures Inspector menu.

4.1.2 Setup Wizard
The Setup Wizard displays during initial assembly and power-up. If Setup Wizard does not display, see Section 2.1 on page 10.
Select the Setup Wizard to automatically step through the following information.

4.1.3 View EULA
The View EULA button displays the Software End User License Agreement.

5. Use or to scroll through the license agreement.
6. Select when read.

4.1.4 Data Extract
If Long Terms Store and Daily Extract are enabled by the system administrator, the operator can view the configuration settings and current/historical status. All settings are configured in the administrator mode of QubeVu Manager.

Select to refresh.
Select to perform a manual export.

Select the ruler icon to return to normal operating mode.

4.1.5 Restart
Select Restart for confirmation before restarting the device. Select to confirm or to cancel the process.

4.1.6 Upgrade Firmware
Updated firmware may be available at www.ricelake.com. When upgrading the unit, the firmware release must be downloaded to a USB drive.

Select Upgrade Firmware.
Attach the USB drive to the iDimension Plus USB port. Select to continue.

Firmware upgrade files contained on the USB drive are displayed.
Select the firmware upgrade required. Select to continue. NOTE: The firmware update is copied from the USB drive to the iDimension Plus. The file checksum is used to validate the file.
Select at the message Uploaded file checksum to proceed with upgrade. The update process takes a few minutes. Do not interrupt the process. The iDimension Plus reboots upon completion.

NOTE: Select to cancel the process.
4.1.7 IP Address
The IP address displays the current IP address defined by the system administrator or network. Use the displayed IP address to configure the network port to access the Administrative QubeVu Manager software for full system setup and configuration.
4.2 Device Information
Provides access to a weights and measures inspector and important information about the device.
Select the ruler icon to return to the normal operating mode.
4.2.1 Device Information Key
The Device Information function key displays the Device Info Menu.
Press to enter into the Device Info menu on the USB touchscreen display. The menu provides access to a weights and measures Inspection menu and Configuration menu for setup of standard user functions (Section 4.2.2).
4.2.2 Weights and Measures
This screen must be accessed by a local weights and measures inspectors for Legal-for-Trade devices using category 3 audit trail.
From the Device Info menu, select the Inspection button .Certification Change Log
The Certification Change Log provides a log of configuration and calibration changes for weights and measures inspectors.

Use or arrows to scroll through the log
Select the ruler icon to return to normal operating mode

Select to return to the previous screen

Transaction Log
For specific applications and International approvals requiring long term storage, audit trail must be configured in the QubeVu Manager Measurement Settings tab. If not configured, No LTS data is available displays.

Use and Operation

For iDimension Series use and operation information, see the following sections:
5.1 Measurement Capabilities
When reporting dimensions of an item, the device defines length, width and height as follows:

Length – Longer of the two horizontal measurements
Width – Shorter of the two horizontal measurements
Height – Vertical measurement

The iDimension Series has been tested and approved with an OIML & MID certified accuracy of ± 5 mm on regular shaped items. See Section 9.0 on page 47 for additional specification information.
NOTE: Minimum and maximum certified capacities do not reflect certified performance specifications. Contact Rice Lake Weighing Systems for details.
NOTE: When a scale is used on top of the base plate, it reduces the maximum object size available since it reduces the distances between the scanning head and base plate.
5.1.1 Flats
Dimensioning objects smaller than 1.2” (3 cm) in height requires the following:

Selection of the correct configuration profile (Section 2.4 on page 14)
A connected scale or use of the Disk Finder feature.

5.1.2 Object Types
The iDimension Plus is factory configured to dimension both cube (rectangular) and irregular shaped objects. Irregular shaped objects are dimensioned as rectangles around the shape.
See Table 5-1 for an example of how and what types of shapes the iDimension Plus will measure.Item Placement
For best results, centrally place the item below the scanning head. If the Zone of Interest or Work Area are configured too small, errors may occur.The maximum size of an item to be dimensioned varies due to the camera’s field of view.
5.2 Performing A Measurement
This section provides an overview of how to perform a measurement.
5.2.1 Automatic Package Detection

To dimension, the iDimension Plus must be in a Ready status and the scale, if used, is at zero weight.
Place object within the Zone of Interest. Once the scale has settled and there is no motion within the Work Area, the iDimension Plus will provide the dimensions, weights and image of the package with a blue bounding box representing the measurements displayed.
NOTE: To enable Manual Trigger Mode, attach an optional bar code scanner or use a third-party software to trigger a dimension.

Remove the object. The system returns to the Ready status.
If the system does not return to the ready state, select the Help function key on the USB display (Section 3.1.5 on page 18) follow the instructions to return the iDimension Plus to the Ready status.

Item Out of Bounds
The system will provide an out of bounds alert if trying to dimension an object that is too large for the field of view. Use the out of bounds indicator to determine if reposition is required. NOTE: See Section 2.3 on page 14 to adjust the scan zone.

Network Connection

iDimension Plus is installed as a network device and supports both static and dynamic IP configuration. DHCP is enabled as default, however, it also has a fixed, failsafe IP address of 169.254.1.1 which can be used for initial setup and configuration.
Configuring the iDimension Plus uses the embedded firmware, QubeVu Manager, which is accessed via an IP address over a wired Ethernet connection through a web browser. 6.1 Connection
If using DHCP, connect the iDimension Plus to the network and follow the instructions in Section 6.2 to determine the IP address. Alternatively, contact your local IT Department.
If using a static IP address, connect the iDimension Plus directly to a laptop or PC and follow the instructions in Section 6.3 on page 33.
6.2 DHCP Connection
To connect via DHCP, see the following information:

Connect the Ethernet cable to the back of the iDimension Plus and to the network.
Power on the iDimension Plus.

The network assigns an IP address.
To identify the IP address assigned from the touchscreen display, select the Device Information function key .
From the Information menu, select the Configuration Menu function key to access the configuration menu.

Select the IP Address button, document the IP address.
Open a web browser, Google Chrome is the recommended web browser, type in the IP address into the web browser, the QubeVu Manager menu displays.
See Section 7.3 on page 38 for advanced network adapter settings.

6.3 Static IP Connection
To connect via the static, failsafe IP, use the following steps.

Connect a laptop/PC directly to QubeVu using a standard Ethernet cable.
NOTE: It is important this is a direct connection with no hubs/switches in between.
Configure the Ethernet port on the laptop/PC with the following IP settings:

IP Address: 169.254.1.10
Subnet mask: 255.255.0.0
Confirm connectivity by pinging 169.254.1.1

If ping is successful, QubeVu Manager should be accessible at http://169.254.1.1

The 169.254.1.1 failsafe address is intended for use during initial setup to access QubeVu Manager and facilitate configuring a static IP address. See Section 7.3 on page 38 for advanced network adapter settings.
6.4 Admin Tools Menu
Admin Tools are used for configuring, calibrating, defining, upgrading, backing up and running diagnostics on the system.
Use the following steps to enter the Admin Tools menu.

From the QubeVu homepage, select to log in.

The default user name is admin and the default password is password.
Select desired tool within the Admin Tools menu.

Parameter	Description
Setup	Configuration settings, define Work Area and Zone of Interest (Section 4.0 on page 21)
Calibration	Calibration settings, calibrate cameras, time and date, data extraction and long term storage (Section 7.0 on page 34)
Capture Definitions	Capture definitions for QubeVu
Firmware Upgrade	Update firmware
Backup	Backup and restore settings; See the iDimension Plus QubeVu Managers Guide (PN 195441) for additional backup details
Diagnostics	Diagnostics settings (Section 9.1 on page 47)

Table 6-1. Admin Tools
6.4.1 Edit/Cancel/Save Keys
While in Admin Tools menus, Edit, Cancel and Save keys are active and are found on the right side of the screen the screen.Edit
Select to make changes to the Admin Tools settings. This displays while in the general setting mode and calibration menu.
Change the settings, then select to continue.
Cancel
Cancels all edits made to all tabs, unless saved.
Save
saves all changes made during the edit process within the page and a sub menu tab. Upon save, the unit may restart and return to the home screen.

Setup

This section provides an overview of iDimension Plus setup instructions, using QubeVu Manager.
For complete QubeVu Manager setup instructions, see the iDimension Plus QubeVu Managers Guide (PN 195441).7.1 Setup Menu
Use the following steps to navigate to the setup menu.

From the QubeVu Manager menu, select .

The QubeVu Manager login screen displays. The username is admin. The password is password.
Select .

7.2 General Settings

From the QubeVu Manager menu, select .
The QubeVu Manager login screen displays. The username is admin. The password is password.
Select .
Select .

7.2.1 General Settings Parameters
Default factory settings are shown in Figure 7-4 and Table 7-1

Parameter	Description
High Resolution Camera	Enables or disables the high resolution camera; NOTE: High resolution cameras are not present in all models. High resolution image capture is controlled by the Capture Definitions
Auto Trigger Flats	Determines if the capture (dimensions, weight, image) is automatically triggered for items classified as flats; On = capture initiated when a flat item is placed in the Work Area, item is stable and a stable weight has been received from a connected scale, default
Auto Trigger Parcels	The default setting is On; A parcel is defined as a package that is determined automatically at 85% or higher in a cuboid score
Logging Level	The default setting is Info; Changing to error or debug will increase the amount engineering and performance information stored in the diagnostics and log files shown in “ipaddress/log” command
Self Recovery	The default setting is Reboot; Off – System will not perform a self recovery; Restart – If the system has determined a critical error state, the unit will perform a restart of the software and returns the system to normal mode; If an object is under the device during a reboot, Wait will be displayed on the USB display; Clear the platform to return to ready state; Reboot – If the system has determined a critical error state, the unit will perform a reboot, an automatic power cycle that clears the error and returns the system to normal mode; If an object is under the device during a reboot, Wait will be displayed on the USB display; Clear the platform to return to ready state; If the scale is receiving power from the USB port, check to make sure the scale is on and working properly

Table 7-1. General Settings Parameters
7.2.2 Scale
The iDimension Plus is designed to directly interface to common shipping scales. Each scale has unique interface protocols that are designed to work with common shipping systems.
Refer to the manufacturers manual to determine the available “protocols” to choose from.
The iDimension Plus provides a USB port for connecting the scale. Some scale manufacturers may vary on the compatibility and capabilities of protocols for a scales with RS-232 or USB connections.
NOTE: A scale with USB HID is a standard Windows and USB.org protocol that works with scales when displaying weight lb or kg. If a Postal Scale displays weight in lb/oz, the USB HID protocol does not function.
If the scale is equipped with only an RS-232 port, a compatible FTDI RS-232/USB Converter (PN 178501) is required.

Parameter	Description
Scale Type	Selectable from a drop-down list: Auto – Upon Start-up or reset, the iDimension Plus automatically attempts to identify a scales factory default settings; It is recommended to use one of the scale manufacturers; USB HID scales are not supported None – No scale is connected External – Requires advanced integration using iDimension Plus API; With no scale connected USBHID* – A compatible scale using scale using USB HID protocol; See Comms parameter Mettler Toledo – A scale configured for the Mettler Toledo Standard protocol MTSICS –A scale configured for using the (Mettler Toledo Standard Interface Command Set) NCI – A scale using the Avery Weigh-Tronix/NCI protocol; For Rice Lake BenchPro Postal Scales, use this setting for scales in lb/oz mode Pennsylvania7300 – The Pennsylvania 7300 scale is used
Communication Parameters USB RS-232	Enter the RS-232 parameter settings of the scale selected; See the scale manufacturers operator’s manual for instructions: Baud Rate – 1200, 2400, 4800, 9600, 14400, 19200, 38400, 57600 and 115200 Parity – None, Odd, Even Bits – 5,6,7,8,9 Stopbits – 1, 1.5, 2 Example: 9600,N,8,1
Communication Parameters USB HID	The following is a list of Compatible USB HID scales including the Vendor ID and product ID; The following example is for a Rice Lake BenchPro Scale; 1C19 is the vendor ID and 0002 is the product id; Use a comma to separate the values (Table 7-3) Example: 1C19,0002

Table 7-2. Scale Parameters

Manufacturer	Model	Vendor ID	Product ID
Rice Lake Weighing Systems	BenchPro Series	1C19	0002
Fairbanks Scale	Ultegra Series	0EB8	0x555e
Mettler Toledo	PS / BC Series	922	F000
Dymo Costar	M10	922	8003
Dymo Costar	S50	922	8007

Table 7-3. Scale Manufacturer Information
NOTE: If the required scale is not listed, contact Rice Lake Weighing Systems to purchase a BenchPro scale.

Parameter	Description
Use Scale Stable Status	Use Scale Stable Status determines when iDimension locks the displayed weight and dimensions on the touchscreen display. Dimensions are locked and the remove state is displayed using both the scale stable reading and iDimension filter Scale+QubeVu – This is the default factory setting and is recommended for use; QubeVu – Dimensions are locked and remove is displayed without checking if the scale is stable; Using this feature may provide incorrect weight on the display; Not recommended for use; Scale – Dimensions are locked and remove is displayed when the scale has returned a stable reading to the iDimension; Not recommended for use, this may increase the remove state to more than 3 seconds
Wait Timeout (ms)	The time in milliseconds the dimensions wait for the scale to return a stable weight; System timeouts and does not return to the remove state; Increase this settings if the scale is in an unstable environment
Scale Delay (ms)	The time in milliseconds in which the iDimension requests a weight from the scale; Increase this setting to 500 ms to allow the weight on the scale to stabilize, if experiencing incorrect weights being displayed on the iDimension vs the scales display

Table 7-4. Use Scale Stable Status Selections
7.3 Network
Use the Network tool to define network settings.
Press while within the Setup menu.
Figure 7-6. Network Interface Settings
Enter or modify the network settings for the enterprise network.

Parameter	Description
DHCP	Have the network administrator verify if the iDimension Plus is to be set up on the network using the Dynamic Host Configuration Protocol (DHCP); If DHCP is checked, a unique Host Name for this device must be defined; The name is used to access the device from the Manager Tools in the future; A host name can be up to 15 characters Example: http://<hostname>/
IP Address	If DHCP is checked, do not enter an IP address; If DHCP is not checked, define a unique IP address for each iDimension Plus is installed; Default IP address: 169.254.1.1 Consult with the network administrator if unsure how to assign a new IP address; If using fixed IP addresses, access iDimension Plus by the hostname or the IP address: http://<hostname>/ http://<ip address>/
Subnet Mask	Default subnet mask: 255.255.255.0; Consult the network administrator for the correct setting
Gateway	Default gateway: 0.0.0.0; Consult the network administrator for the correct setting
Hardware Address	Do not modify; Each iDimension Plus has been assigned a unique hardware address
Host Name	The default host name is the alphanumeric portion of the device serial number; A unique host name may be defined for each device; Up to 15 characters are allowed for the Host Name

Table 7-5. Network Interface Parameters
7.3.1 Network Security
Network Security settings allow enhanced security by encrypting communications with the iDimension Plus using the Hypertext Transfer Protocol (HTTPS). By default, communication with the iDimension Plus is via HTTP.

Select the Network Security tab to display the current settings
Click on Enable HTTPS to enable HTTPS
Click Browse to select your SSL key and cert files, then Upload
Select Upload to transfer the information from the PC to the iDimension Plus

NOTE:SSL certificates are not supplied by Rice Lake Weighing Systems. Contact your IT Department for further information. NOTE: With HTTPS enabled, both the HTTP and the HTTPS addresses are available.

Calibration

This section provides an overview of iDimension Plus calibration instructions.
The calibration menu provides access to the following information:

Calibration settings for the Work Area and Zone of Interest configuration
Camera calibration – if required, calibrates the iDimension Plus using the calibration object

8.1 Calibration Settings
The calibration settings include configuration of the Work Area and Zone of Interest.
8.1.1 Work Area
The Work Area represents the area around the base used for detecting motion. The system waits until there is no motion detected before attempting to scan an item.
The Work Area also provides a maximum area for the detection of flats (items less than 1.2” in height) and irregular objects.
Flats and irregular objects must fit completely within the Work Area in order to be detected.
When configuring the Work Area, this area should be clear of objects that would affect dimensioning performance. IMPORTANT: Figure 8-1 is for flats and irregular objects only. Parcels are dimensioned even if part of the item is outside of the Work Area.
8.1.2 Zone of Interest
The Zone of Interest represents the detection area to be used for item dimensioning. Items must be placed at least partially within the Zone of Interest. NOTE: If the background of the dimensioning area is reflective, adjust the Zone of Interest to approximately 3” x 3”.
8.1.3 Zone of Interest Configuration Mode
To review the current camera calibration settings within QubeVu, see the following procedure:

From the Admin menu, select to enter the setup menu.
Select to set parameters within the Calibration Settings tab.
Select the Zone of Interest tab.
Select to switch to configuration mode. This may take a few minutes while the device resets. NOTE: Modifying the Zone of Interest and Work Area is required if the height of the scale has been changed or if a scale has been added or removed from the operation.
Once the system has successfully entered into the edit and configuration mode, a live image will be displayed.
Select or and hold the mouse over the image to create new parameters.
NOTE: Ensure the Work Area is larger than the Zone of Interest.
Select to continue. The system restarts. Ensure the platform is clear of obstructions to return to the ready state.

8.2 Camera Calibration from QubeVu Manager
For camera calibration information, see the following procedures:
8.2.1 Camera Calibration
The system is factory calibrated however it is may be required to perform a calibration if the system has moved to a different location, new scale is being used or the system is providing inaccurate dimensions.
Calibration requires the use of the included calibration object.
If using a scale, make sure the scale is centered between the marks on the base plate and place the calibration object on top of the scale platform.
If no scale is used, place the calibration object between the base plate mark.To calibrate the camera, use the following steps:

From the Admin menu, select .
Select . The Camera Calibration menu displays.
Select
Select the Depth Confidence tab. A live image displays.
Press and hold the left mouse button and hover over the image to create a blue rectangle line around the calibration object.
Select the Low Resolution tab.
Press and hold the left mouse button and drag the mouse to draw a rectangle around the calibration object.
If a 4k model has been purchased, select the High Resolution tab.
Press and hold the left mouse button to drag the mouse to draw a rectangle around the calibration object.
Select Calibrate. must display on each tab for the calibration to be successful.
Review each tab to ensure the calibration object was successfully captured and no other object had mistakenly been placed in the view of the camera.
Select . The unit automatically restarts to apply the camera calibrations.

Calibration Unsuccessful
If displays, the calibration has failed. The red cross hairs out of alignment indicate they are out of alignment and a new calibration is required.

Select Cancel and perform a new calibration.
Redraw the rectangles within each available tabs.
Calibrate again until both tabs display.

If unsuccessful calibration continues, check for:

The dimensioning head is level.
Sunlight is not within the background and field of view of the camera.
Glare from overhead lights are within the background and field of view of the camera.
The workspace or background has to much clutter, or noise from other objects.

Appendix

This section provides an overview of additional iDimension Plus instructions.
9.1 Diagnostics
This section provides an overview of iDimension Plus diagnostics instructions.
The Diagnostics tools can be used to test hardware components and gather diagnostic information.
NOTE: The Administrator defined a username and password during the initial setup process. The username and password are required to log into and access the iDimension Plus Admin Tools.
9.1.1 Diagnostics Menu
The Diagnostics menu provides tools to help troubleshoot the device.
From the Admin menu, select to enter the diagnostics menu.
The Diagnostics menu has four tools used for testing hardware and providing information about the system.9.1.2 Component Tests
The Component Tests menu is used to test hardware components individually or all at once.

Select Test All to test all hardware components; If a scale is connected the camera level test will fail
Select to test individual components

The status of each individual component is returned as either Passed or Failed. Additional details can be viewed by selecting the test name.Table 9-1 lists common troubleshooting tests to run:

Field Test	Description
Depth Sensor	Tests the main sensors to determine operating status
High-res Camera	Tests the high resolution camera to determine operating status
Scale	Tests the scale is communicating using the scale parameters configured in Admin Tools > Setup > General Settings
Network	Tests the network link speed. Failure is indicated when the link speed is < 1000Mb/s
DMESG	Displays information on low-level hardware components
Camera Level	Manufacturing test; Not intended for field use
Top	Displays information on CPU and memory utilization
PS	Displays information on running processes
Serial Number	Checks for a valid serial number and model
Port	Displays information on USB buses
Temperature	Displays the SBC temperature

9.1.3 Scale Test
The Scale Test tool is used to help determine the communication settings of a serial scale attached to the iDimension Plus.

Select the Serial Port and Scale Type from the drop down lists.
Select to start the test.
If a valid scale is detected, the output provides the scales communication parameters.

9.1.4 System Log
The system log storage data is configured in the setup menu. For troubleshooting, the file may be required to be sent to the factory for engineering analysis and troubleshooting. The log view can be customized by type (view all or view info, debug or error messages only) or by order (view the latest first or the earliest first).The log can be refreshed by pressing or automatically refreshes by checking the auto refresh box.
To download the log to a CSV file, press Download.
9.1.5 Debug Info
The Debug Info is a file that provides engineering and trouble shooting information of the operation of the unit.
This file may be requested for troubleshooting purposes. Select the desired information to be downloaded.

Press Download to save the file to the computer.

9.2 Troubleshooting
This section provides an overview of iDimension Plus troubleshooting instructions.
9.2.1 iDimension Plus Does Not Return to Ready State

Select on the display.
Follow the provided help instructions to return the iDimension Plus to Ready state:
A. Device status: STARTED or REMOVE displays; Clear the scale of obstructions
B. Zero the scaleC. The iDimension Plus is zeroed

9.2.2 iDimension Plus Display is Off or Blank

Check the power connection on the back of the iDimension Plus and the 120 V outlet.
Check USB connection on back of USB display.
Press the Power button on the back of the USB display.
Power cycle the iDimension Plus.
Check connection on scanning head.

9.2.3 iDimension Plus Display is Green

Check access to QubeVu Manager.
Connect a laptop/PC directly to QubeVu using a standard Ethernet cable. It is important this is a direct connection with no hubs/switches in between.
Configure the Ethernet port on the laptop/PC with the following IP settings:
• IP Address: 169.254.1.10
• Subnet mask: 255.255.0.0
Confirm connectivity by pinging 169.254.1.1
If ping is successful, QubeVu Manager should be accessible at http://169.254.1.1

9.2.4 iDimension Plus Display is Locked and Will Not Dimension

Power cycle the iDimension Plus from an AC Outlet.
Restart the iDimension Plus.
Select on the touch screen display.
Select .
Select Restart.
Select to restart the device.
The USB display will go to a green display and within 2 minutes return to the ready state.

Compliance

DECLARATIONOF CONFORMITY

Rice Lake Weighing Systems
230 West Coleman Street
Rice Lake, Wisconsin 54868
United States of AmericaType:iDimension Plus
We declare under our sole responsibility that the products to which this declaration refers to, is in conformity with the following standard(s) or other regulations document(s).

EU Directive	Certificates	Standards Used / Notified Body Involvement
2014/35/EU LVD	–	EN 62368-1:2014+A11
2014/30/EU EMC	–	EN 55032:2015, CISPR 32:2013, EN 61326-1:2013
2011/65/EU RoHS	–	EN 50581:2012

Signature:Name: Brandi Harder
Title: Quality Manager
Place: Rice Lake, WI USA
Date: June 15, 2021
DECLARATION OFCONFORMITY
Type: iDimension Plus
We declare under our sole responsibility that the products to which this declaration refers to, is in conformity with the following standard(s) or other regulations document(s).

UK Regulations	Certificates	Standards Used / Approved Body Involvement
2016/1101 Low Voltage	–	EN 62368-1:2014+A11
2016/1091 EMC	–	EN 55032:2015, CISPR 32:2013, EN 61326-1:2013
2012/3032 RoHS	–	EN 50581:2012

Signature:Name: Brandi Harder
Title: Quality Manager
Place: Rice Lake, WI USA
Date: December 30, 2021

Specifications

Product Dimensions

Length	25” (63.5 cm)
Width	14.25” (56 cm)
Height	63.8” (162 cm)
Weight	28.5 lb (13 kg)

Power Requirements
Single power source 110–240 V external power supply, US power cord
Object Colors
All opaque packaging
Measurement Time
0.2 seconds, scale setting times vary by manufacturer
Cuboidal Specifications

	Length	Width	Height
Maximum Length	5 48″ (120 cm)	5 28″ (80 cm)	5 28″ (80 cm)
Minimum Dimension	.? 5.6″ (14 cm)	5.6″ (14 cm)	2.0″ (5 cm)
Accuracy	± 0.2″ (0.5 cm)	± 0.2″ (0.5 cm)	± 0.2″ (0.5 cm)

Irregular Specifications

	Length	Width	Height
Maximum Length	5 48″ (120 cm)	28″ (80 cm)	5 28″ (80 cm)
Minimum Dimension	? 5.6″ (3 cm)	1.2″ (3 cm)	0″ (0 cm)
Accuracy	± 0.5″ (1 cm)	± 0.5″ (1 cm)	± 0.5″ (1 cm)

NOTE: Specifications depend on hardware configuration and certification requirements. Please contact your sales representative for further information.
Operating Temperature
32°F–86°F (0°C–30°C)
Humidity
Non-condensing
Mechanical Environment Class
M1
Electromagnetic Class
E1
I/O Ports
(1) USB type A port (interface to scale)
(1) 10/100/100BASE-T Ethernet port (interface to PC)
Software Integration
API and SDK files available for network device integration
Warranty
Two-year limited warranty
Certifications and Approvals

	NTEP CoC Number: 19-040A1
	EU File Number: T11908
	OIML File Number: R129/2000-A-NL1-20.05

© Rice Lake Weighing Systems Content subject to change without notice.
230 W. Coleman St.
Rice Lake, WI 54868
USA USA: 800-472-6703
International: +1-715-234-9171
September 15, 2023
www.ricelake.com
PN 206286 Rev C

Documents / Resources

RICE LAKE 6756 Plus Static Dimensioning System [pdf] Instruction Manual
6756 Plus Static Dimensioning System, 6756, Plus Static Dimensioning System, Static Dimensioning System, Dimensioning System, System

References

User Manual

6756 Plus Static Dimensioning System