rako RK-HUB 2024 Wireless Ethernet Hub User Guide

Network interface : Local Programming, App control and IP integration of 3rd party control systems.
Cloud Gateway: I nterfaces with Amazon Alexa, Google Home, Apple Homekit, Sonos etc.

Storing Project ﬁle information: Room, Channel and Scene information can be stored.
Timed Events : Automatic functions at ﬁxed times including dawn & dusk.

Mapping : Commands can be redirected to perform other tasks.
Macros : A series of commands that are triggered by a single command or event. Speciﬁc steps can be enabled and disabled giving conditional functionality.

Holiday Mode: Replays recorded system activity, creating an occupied appearance to a property.

Installing the RK-HUB

Step 1: Plug DC power supply into RK-HUB and available 13A socket.
Step 2: Plug the Ethernet patch cable from the RK-HUB to a spare port in a router or network switch.

Step 3: Mount the RK-HUB to a wall using the ﬁxing plate if required.

Discovering the HUB and Setting the House Number

Before proceeding with any programming, the HUB needs to be discovered and the House number set. This is done via a webpage setup wizard.

Discovering the HUB

Open Rasoft Pro programming software. Ensure that the laptop is connected to the same network as the HUB.
The HUB should appear in the “Communication” window in the bottom right of the software with a red stop sign. If it does not appear, press “Refresh.” If it still does not appear, refer to Section 3.4 of this manual.

Setting up the HUB using the Webpage Wizard
To access the HUB webpages, right-click the communication device in the bottom-right corner of the software. Select “Open in Browser.”

Step 1: On the Welcome page, select “Next to begin setup.”
Step 2: Set a password; this will be used to login to the webpages. It will also be the password used to login to the App if a password is needed.

Step 3: Sets the House number of the HUB and therefore system. This should be set to match the Rasoft Pro project ﬁle as deﬁned in the “New Project Wizard.”
Step 4: Select “Finish” to complete setup.

Managing the HUB House number
Leaving the HUB at the default House address of 1 is strongly discouraged. Leaving the House number at 1 drastically increases the likelihood of interference from nearby Rako systems.
The HUB always has a default House Address of 1, fit has not been set up before . Before programming using the HUB, it is important to ensure the HUB House number corresponds to the Project File House number.

Change the House number if the HUB has already been set up as described in 3.2. See below:

As a ﬁnal check, it is advisable to disconnect and reconnect to the HUB by double-clicking the HUB:

If no pop-up box appears, then the HUB House number and Project File House number are the same.

WARNING
I f a pop-up box appears with a warning about the House number, click “Cancel.” Do not continue programming; this means there is a conﬂict between the “ Project File House Number ” and the “ HUB House Number. ”

If you cannot connect to the HUB

If the software cannot connect to the HUB, ﬁrst restart the software and ensure that it is fully updated. If the HUB still does not appear, it is most likely a networking issue. If this problem cannot be solved, then the HUB can be connected point-to-point using a standard Ethernet cable.

Linking the HUB for cloud services

To be able to access cloud services, the HUB must be linked to a my.rakocontrols.com account.

Where to ﬁnd each cloud service
Some cloud services are conﬁgured and customised from the HUB webpage, whereas others are from my.rakocontrols.com
HUB webpage: Sonos Activities (new cloud API and “ACM” style custom IP strings) including custom and default templates (RCM/WCM-audio style keypads)
my.rakocontrols.com: Amazon Alexa, Google Home and Apple Home including “Custom Scenes” and advanced apple Home conﬁguration (Channel and Room mode etc.)

NB
More detailed descriptions of how to use the advanced settings within the cloud services are linked from the relevant section of either the HUB webpages or my.rakocontrols.com

Linking the HUB to Cloud services
This is linked via the HUB webpages; navigate to the “Cloud” section from the menu on the right-hand side of the screen. This will open a page, as below:

Step 1: Press “Connect”; this will link you to the my.rakocontols.com page.

Make sure that all “Service Status” is green before proceeding with the following steps:
Step 2: Press “Login/Register” if you already have an account at my.rakocontrols.com; use the email and password that are used for this; if not, create an account.
Step 3: Once logged in, the code within the HUB will be automatically veriﬁed.
Please wait; this process may take a couple of minutes
Step 4: Once it has been linked, the HUB will ask to be given a “Nickname”. This is how it will be referred to in the my.rakocontrols.com interface. It is not the same as the “HUB name” as deﬁned within the HUB setup wizard.
Once completed, the my.rakocontrols.com “Devices” page should appear as below:

Adding the HUB as a device to Rasoft Pro

Once the HUB has been successfully connected, it will need to be added to the software as a device. Please note that this guide assumes that your project ﬁle has already been created as described in the relevant Rasoft programming guide.

Step 1: Select “File”- “New Device” to open the new device wizard. Choose “Bridge” as the device to be added.

Step 2: Select “Next” on the “Assign to Room” step. No room or channel needs to be associated with the HUB.
Step 3: Select the HUB from the list; it will appear if you are successfully connected in the communications window. Click “Refresh” if it does not appear.
Step 4: The HUB should now appear in the device list with green text and a blue icon. The device is now assigned.

Uploading the project ﬁle

Once the entire system has been completed, the project ﬁle should be uploaded to the HUB. The HUB stores the Room, Channel and Scene information for the system. This information is required for the App. to operate correctly.
The “Smartphone/Web Data” tab is used to upload the Project File to the HUB. Once selected, it will open the page as below. Press “ Save & Upload Room Data To Bridge ” to upload.

Type – This will change the appearance of the icon used at the top of the room screen on the App. It will also affect the keypad that appears. For example, a room set to “switch” will show two buttons: “on” and “off,” whereas a “blind” type room will show three buttons: “open,” “stop,” and “close.”
Mode – The mode of the room is only set when “lighting” is selected as the type. It will set the variety of “keypad” that will appear in the App. Typically, it is best to make this match the physical keypad in the room.

If there are a speciﬁc number of scenes that are not in the standard 4, 7, or 16 layout, then “named scenes” should be selected. Give custom names to the scenes in the room editor, and any number of scenes can be made to appear on the App.
While the order of the rooms can be changed from this screen, the order of the channels is always ﬁxed. To get channels in a speciﬁc order, they must be addressed or mapped in the desired order.

Downloading the project ﬁle

If information has been uploaded to the HUB, then it is possible to import the Room, Channel and Scene data into a blank project ﬁle.
The tab used for downloading information from the HUB is called “ Room Import, ” Select it to open the page below.

Step 1: Press “Download Data” at the top of this page. This will open the data for preview on this page.

Step 2: Press “Refresh List” if the rooms do not appear. If no rooms appear or only “default room” or “test bench,” then there is no information to be downloaded from the HUB.
Step 3: Press “Import Data” to write the Room and Channel information into the Project File.
Step 4: Press “Refresh Channel Levels” to write the Scene data into the Project File.

Events can be viewed, added, and edited using either Rasoft Pro, the Rako App, or the HUB webpages. It should be noted that calendar event conditions can only be set from the HUB web page interface.
The HUB can generate automated Events that trigger commands at speciﬁc times.
For example, it is possible to automatically turn on the Garden lights at Dusk and turn off the Garden lights at Dawn.

Events

Events can be viewed, added, and edited using either Rasoft Pro, the Rako App, or HUB webpages. It should be noted that calendar event conditions can only be set from the HUB web page interface.
The HUB can generate automated Events that trigger commands at speciﬁc times.
For example, it is possible to automatically turn on the Garden lights at Dusk and turn off the Garden lights at Dawn.

Setting Events using Rasoft Pro
HUB Events can be viewed and edited using Rasoft Pro. To open the events page in the software, select the HUB in the device editor and select the “Events” tab from the top of the window.

Mappings List:
All Events are listed on the left-hand side of the events tab. Select an event such that it is highlighted to edit the “Event Trigger/Active Days” and “Output Action” sections for this Event.

Event Trigger/Active Days:
“Event Trigger” and “Active Days” are the timing conditions that deﬁne when the event will occur.

NB
The dawn and dusk settings can be changed via the location settings in the webpage interface. An offset from this value can be set from this screen if desired.

Output Action
The Output action section on the right-hand side of the screen will deﬁne the command to be sent when both the conditions in “Event Trigger” and “Active Days” are met.

NB
The “Action” drop-down menu is used to select the command sent when the event is triggered.
Typically, these will be scene commands but it is possible to trigger and control Macros, Holiday settings, etc.

Setting Events using the Rako App.
Events can also be created via the Rako App. The method to create events in the App is essentially the same as detailed above.
For more information, please refer to the App User Guide.

Activities

Setting Events using Activities
Events can be set via the “Activities” section of the HUB webpages. Navigate to this by selecting “Activities” from the menu on the left-hand side of the HUB web pages and then selecting “Edit” on “Rasoft Pro Activity.”.

Type:
This is the time at which the output of the event will occur. It can be deﬁned via a 24-hour clock or in relation to the year-round tracked dawn/dusk time internal to the HUB.

Condition:
A condition requirement can be added to the event that needs to be satisﬁed for the output of the event to occur. This can be a day of the week or a calendar condition.

Output:
The command will be sent when the “Type” and “Condition” are both met. This will usually be a Scene but can also be a level, fade, etc.

Setting Audio Activities
The HUB has built-in templates to integrate with third-party audio players, such as Sonos ® and BlueSound .

Step 1: Select the “Activities” section on the HUB webpages.
Step 2: Select “Use Template Activity.”

Step 3: Choose the template that represents the keypad layout required and select ‘ Create Activity’
Step 4: Select ‘Get Players’; this will scan the local wired network for audio devices, and choose from the selection.
Step 5: Select the Virtual Room to which the audio device will be mapped

Step 6: Select ‘Create Activity’

Once the Activity has been created, the Rako Room selected in the Activity will have the commands processed by the HUB, which will communicate with the audio device over IP.

Mappings

When Mappings are used, the HUB can “listen” to a Rako command (Source) and perform a certain action (Output Action) every time it is “heard.”

NB
I t is usually preferable to use a programmable keypad rather than HUB Mapping when possible. Where WCMs and RNCs are used in the system, use Keypad Mapping rather than HUB Mapping.

Mapping wireless commands to give multi-room functionality
Wireless commands can be mapped to additional wireless commands to make multiple rooms turn on at once. In the example below, “Hall Scene 1” is mapped to also trigger “Kitchen Scene 1.”

NB
It is also possible to “Enable” and “Disable” maps from other commands via the “Mapping Control” Action.

Triggering Macros from Maps
When a Macro is used, it must be triggered from a map (this could also be from a WCM map, WAVFR map, etc.). Below Mapping 2 is an example of a map being used to trigger a macro: in this case, “Start Macro 2.”

Macros

Macros allow a sequence of actions to take place when triggered by an Event or Map. The HUB can store up to 60 Macros, each of which can have a maximum of 32 steps.
The HUB Macro screen is located on the tab in the HUB device editor.

There are 3 steps in this example Macro:

Room 9, All Channels, Scene 2

Room 17, All Channels, Scene 1
Room 49, All Channels, Scene 2

With this simple Macro the HUB will just run through the three commands listed. More complex functionality can be achieved by using the commands in the tables outlined below.

Writing Macros
Macro steps can be one of four types:

Action

Pause

Delay

Goto

Can be a simple	A running Macro will	The Macro can wait at	The Macro can be
command, including	stop at a Pause and	this step for a deﬁned	sent to a deﬁned step
Scenes, Fades etc.	remain there until it	period of time. Useful	in this or another
Can also include	hears a Continue.	when programming	Macro.
“Macro Control” and		PIR timeouts, etc.
“Mapping Control”
for more complex
programming.

Triggering Macros
Macros can be triggered in several ways. Most commonly:

Wired device direct Map (WCM, WAVFR, etc.)

HUB Mapping
HUB Event

Once a macro trigger is sent, it will perform one of four different functions for a Macro:

Start	Stop	Pause	Continue
This will cause the	This will cause a	This will cause a	This will cause the
Macro to start from	Macro that is already	Macro to Pause at	Macro to continue
the beginning (Step	running to Stop	whatever step it is	from a Paused state,
1), regardless of its	running and return to	currently running.	performing the step
current position in the	Step 1.		immediately after this
Macro.			and proceeding.

NB
It is also possible to “Enable” and “Disable” Macros (or parts of Macros) via the “Macro Control” Action.

Holiday Mode

Holiday mode allows the HUB to record normal lighting activity in the system over a period of time. This can then be replayed while the property is empty in order to give a realistic impression that it is occupied.

Holiday mode has three states:

Record : Used to create a log of the system.
Playback : Used when the house is unoccupied to replay the information gathered in “Record.”
Idle : Used when the system is in normal occupied operation and no recording is being made. Holiday mode is most easily controlled from the App. However, it is also possible to change the holiday mode state from a keypad map, HUB map, or by selecting commands on the HUB webpages.
NB: For how to control Holiday mode via the App. see “ App User Guide .”

Upgrading the HUB

Do not update the HUB through RASOFT Pro; always do so through the HUBs webpage.

Step 1: Access the HUB webpages as shown in section 3.3 of this manual
Step 2: Using the HUB web pages, select the “Help” section so that you have the page shown below.

Step 3: Click on the updates panel.
Step 4: This will show the current firmware of the HUB as well as the latest version available.

NB
As the HUB is a new product, it will require updates to have all the features available. Complete the following steps to make sure the HUB is updated to the latest ﬁrmware and all features are available .

UDP Feedback

It is possible to monitor commands received and transmitted by the HUB. This can be done using the UDP Feedback feature.

Live feedback
In the very bottom right of the software (below the communications window) is the Live Feedback section. Each command received or transmitted by the HUB will appear here, and it is useful for checking commands that have been programmed as desired.

NB
A Bridge or HUB will have to be connected in order to see this feedback.

UDP feedback log
When more detailed or long-term feedback is required, a log of commands received or transmitted by the HUB can be opened. In the toolbar, select “Window” – ”Output” – ”Output” to view the page as below:

HUB webpage logs
A timestamped log of system activity can be found within the HUB webpages. These can be accessed by selecting the “Logs” section of the HUB webpages.

As well as a description of the address (Room and Channel) and command, the source of the command can also be viewed.

Activity States

The “Activity States” page in the system settings of the HUB webpages is used to trigger Events, Mappings, and Macros. This can be useful for testing purposes, for example, testing Dawn and Dusk Events or Macros.

Each green number is an active Mapping, Event, or Macro, and by clicking on the box, it will be enabled. This can be veriﬁed by selecting the HUB logs where the command should be visible.

Thank you for choosing Rako Controls; we hope that you are pleased with your system. Should you require further assistance, please contact us via our website, www.rakocontrols.com, or by calling our customer support
helpline on 01634 226666.

Manual Version 1.4.4

Documents / Resources

rako RK-HUB 2024 Wireless Ethernet Hub [pdf] User Guide
RK-HUB 2024, RK-HUB 2024 Wireless Ethernet Hub, RK-HUB 2024, Wireless Ethernet Hub, Ethernet Hub, Hub

References

User Manual

rako RK-HUB 2024 Wireless Ethernet Hub

Specifications

FAQ

Functions of the RK-HUB