Q-TRAN LUME-01 Fully Encapsulated Flexible Fixture

ATTENTION: Please read all instructions BEFORE installation

• Product to be installed by a licensed electrician – Field modifications void warranty
• Use only with Class 2 power supply unit — Compatible for use with Q-Tran power supplies
• Surface mount or recessed in millwork
• Not rated for walkover
• Input Voltage: 24VDC
• Diagrams for representation only and not to scale.

METHODS OF INSTALLATION

Mounting Method

• WSC (page 6)
• MC (page 7)
• PPS-LP-CL-2 (page 8)
• PPS-LP-CL-96 & PPS-LP-CL-FT (page 9)

Cove, Under & over cabinet:
Ideal for office, retail, hospitality, education, laboratory, and residential.

Shelf:
Ideal for office, retail, hospitality, education, laboratory, and residential.

Display cabinet:
Ideal for retail and hospitality

Signage:
Ideal for lobby, retail, hospitality, institutional, and transportation.

COMPONENTS & HARDWARE

MOUNTING CLIP & MOUNTING CHANNEL
WSC	MC
White snug clip	Magnetic clip (Cove use only)
Included	Included
#6 Flat Screw (one provided for each clip)	#6 Flat Screw (one provided for each clip)

SEAMLESS MOUNTING CLIP & SEAMLESS MOUNTING CHANNEL
PPS-LP-CL-2	PPS-LP-CL-96	PPS-LP-CL-FT
Low profile PVC mounting clip	Low profile PVC channel	Low profile PVC channel
Included	Included	Included
#8 flat head screw (1 screw for every 16”) No wireway	#8 flat head screw (1 screw for every 16”) No wireway	#8 flat head screw (1 screw for every 16”) No wireway Custom length

ACCESSORIES SOLD SEPARATELY

Q-ANGLE; sold in pairs

Q-ANGLE

Included

4 SS #6×1.25” Flat head wood screws 2 SS 4-40 Flat head clip screws 2 SS 6-32 Fillister screws

NOTES:
MOUNTING CLIP	SEAMLESS CLIP
2 white snug clips provided per first 12”, 1 for each additional 12”. Other mounting styles incur additional charge, see price guide for details	PPS-LP-CL-2to join two fixtures together PPS-LP-CL-96/FT to support the fixtures PPS-LP-CL-FT is to be cut at Q-Tran to requested length

CONTINUOUS WIRING CONFIGURATION OPTIONS

Review wire method to ensure clean installation prior to mounting finished fixture.

NOTE: Additional wire methods include:
S1: Connector/Wire Input only
P1: Connector/Wire Input and Output

SURFACE MOUNTING METHOD

SURFACE PREPARATION

1. Temperature and environmental concerns
   • Ideal application environment is 70-100ºF in 50% humidity or less.
   • Minimum application temperature: 50ºF
   • This temperature and humidity should be maintained for 72 hours after application for maximum holding force.
   
2. Using a 50/50 alcohol mix, thoroughly clean the backside of the fixture and the surface area where fixture will be installed. Allow 5 minutes to dry.
   
3. Using a 50/50 alcohol mix, thoroughly clean the backside of the fixture and the surface area where fixture will be installed. Allow 5 minutes to dry.
   

MATERIALS	SUGGESTED EPOXIES
Concrete, Stone, Cinderblock, Metal, and Brick	Loctite Metal and Concrete Two-Part Epoxy
BS, Fiberglass, Plastic, and PVC	Loctite Plastic Two-Part Epoxy
Tile, Wood, Ceramic, Glass, or Metal	Loctite Clear Two-Part Epoxy
All Purpose	Strong Stik

SURFACE MOUNTING METHOD: WHITE SNUG CLIP

• 2 clips provided per first 12”, 1 for each additional 12”

1. Determine the fixture(s) location and positioning on desired surface; evenly distribute clips. Make any necessary reference markings to indicate where each clip is to be secured in place. Recommended every 12”.
   
2. • Secure clips using the #6 flat head hardware provided
   • Ensure the screw head is flush with the clip’s base.
   
3. Snap fixture onto clips.
   

MOUNTING METHOD: MAGNETIC CLIP

• 2 clips provided per first 12”, 1 for each additional 12”

1. Determine the fixture(s) location and positioning on desired surface; evenly distribute clips. Make any necessary reference markings to indicate where each clip is to be secured in place. Recommended every 12”.
   
2. Attach clips to fixture matching magnet distances.
   NOTE: Flat head screw type is dependent on surface/application material.
   Alternative flat head screws may be required. Refer to the surface material manufacturer for suggested screw type.
   
3. Align and snap fixture to magnetic rings.
   

SEAMLESS MOUNTING METHOD: PPS-LP-CL-2

• Connects two fixtures, with no wire exit
• 2” low profile PVC mount channel

1. Snap in 2” channel.
   
2. Press fixture into mounted PPS channel.
   
3. Finished assembly for end feed mounting
   

SEAMLESS MOUNTING METHOD: PPS-LP-CL-96 / PPS-LP-CL-FT

• Support two fixtures, without built-in wireway
• 96” (PPS-LP-CL-96) or custom length (PPS-LP-CL-FT)low profile PVC mount channel

1. The PPS-BRACKET can be field cuttable and cut to whatever length your application requires. The PPS-BRACKET can be  installed as a full length of 96”, multiple smaller pieces, or end to end for longer seamless runs.
   Using pre-drilled pilot holes screw the #8 flat head screws to mount the PPS-BRACKET (1 screw every 16”).
   NOTE: For drywall applications mount directly into a stud.
   
   
2. Using pre-drilled pilot holes, use the #8 flat head screws to mount the PPS-BRACKET.
   
3. To mount, pinch the upper half of the PPS-LP-CL-96 or PPS-LP-CL-FT while you pivot it around one side of the PPS-BRACKET and push-in until you hear it snap into place. The PPS-LP-CL-96 or PPS-LP-CL-FT flexes around the PPS-BRACKET to create a solid, and secure snap on connection
   

Customer Support

© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | sales@q-tran.com | www.q-tran.com Specification subject to change. Rev-05-05-23 9 

Documents / Resources

Q-TRAN LUME-01 Fully Encapsulated Flexible Fixture [pdf] Instruction Manual LUME-01 Fully Encapsulated Flexible Fixture, LUME-01, Fully Encapsulated Flexible Fixture, Encapsulated Flexible Fixture, Flexible Fixture, Fixture

References

• User Manual