oricom UHF390R 5 Watt UHF CB Radio with Controller Speaker Mic User Guide

Position the microphone plug with the plastic flap facing
upward and insert it into the socket until it clicks.
Gently press the rubber boot into the hole surrounding the
socket for a secure fit.

Extension Cable Accessory:

Microphone Extension Cable:
- Install the microphone to the socket end and the plug end into
  the transceiver.
- Use this extension where the transceiver is mounted away from
  the driver for more installation options.

Pass-Through Extension Cable:
- Connect one end to the rear of the pass-through and the other
  end into the transceiver. Plug the microphone into the
  pass-through.
- This cable is used when a UHF pass-through connector is
  installed in the vehicle dash.

Antenna Information

The antenna is crucial for optimal performance. Purchase an
antenna designed for the 477MHz frequency band to maximize output
power and receiver sensitivity.

Frequently Asked Questions (FAQ)

Q: Can I use any antenna with this UHF radio?

A: No, it is recommended to use an antenna designed specifically
for the 477MHz frequency band to ensure proper performance.

Q: How do I set up the controller speaker microphone?

A: Follow the instructions provided in the manual to position
and secure the microphone plug into the socket of the controller
speaker.

Q: When should I use the pass-through extension cable?

A: The pass-through extension cable is useful when a UHF
pass-through connector is installed in your vehicle dash, allowing
for easy connection and disconnection of the microphone when using
the radio.

View Fullscreen

UHF390R Quick Set Up Guide

For the full product user guide, please scan QR code or visit www.oricom.com.au

Pack contents
· UHF CB Radio Transceiver · Heavy Duty Controller Speaker
Microphone · Microphone mounting bracket · Transceiver mounting bracket

· Pack of supplied mounting screws · Quick Start Guide · 1 x Microphone extension cable · 1 x Microphone extension cable
(pass through compatible)

Please read before installing or operating your Oricom radio
The operation of your UHF radio in Australia and New Zealand is subject to conditions in the following licenses: In Australia, the ACMA Radio communications (Citizen Band Radio Stations) and in New Zealand by MED the General User Radio License for Citizen Band Radio.

Need help? Contact Oricom Support
If you need assistance setting up or using your Oricom product now or in the future, call Oricom Support.

Australia

(02) 4574 8888 www.oricom.com.au Mon-Fri 8am 6pm AEST

New Zealand

0800 67 42 66 Mon-Fri 10am 8pm NZST

When a new narrowband radio receives a transmission from an older wideband radio the speech may sound loud and distorted simply adjust your radio volume for the best listening performance. When an older wideband radio receives a signal from a new narrowband radio the speech may sound quieter – simply adjust your radio volume for best listening performance. When operating a narrowband radio or Channel 41 – 80 interference is possible from wideband radios transmitting on high power or on adjacent frequency.
The issues described above are not a fault of the radio but a consequence of mixed use of wideband and narrowband radios.

This unit complies with all relevant Australian and New Zealand approval requirements AS/NZS 4365:2011 1

Controls and Indicators Front View of Controller Speaker Microphone

LCD display Microphone On/Off/Volume/ Channel/Squelch
Speaker

Scan/Memory skip/ Memory 1
Priority channel recall/ Key lock/Memory 2 Replay/Monitor/ Memory 3 Triple watch/Menu/ Memory 4
Memory recall/ Memory write

Rear View of Radio

3.5mm external jack for optional 8 ohm speaker

Power supply connection Antenna Jack

LCD Icons & Indicators

Signal strength RF

Record/

Triple Duplex

output & TX meter (SRF) Playback On watch on on

Status Channel display display

CTCSS or DCS Scrambler DCS CTCSS Roger Memory

channel display on

on on Beep on channel

Warnings and Safety Information

Potentially Explosive Atmosphere Turn your radio OFF when in any area with a potentially explosive atmosphere. Sparks in such areas could cause an explosion or fire resulting in injury or even death. WARNING NOTE: Areas with potentially explosive atmospheres are often, but not always clearly marked. They include fuelling areas such as below deck on boats; fuel or chemical transfer or storage facilities; areas where the air contains chemicals or particles, such as grain, dust, or metal powders; and any other area where you would normally be advised to turn off your vehicle engine. Blasting Caps and Areas To avoid possible interference with blasting operations, turn your radio OFF near electrical blasting caps or in a “blasting area” or in areas posted: “Turn off two way radios.” Obey all signs and instructions. Electromagnetic Interference/Compatibility Nearly every electronic device is susceptible to electromagnetic interference (EMI). To avoid the possibility of electromagnetic interference and/or compatibility conflicts, turn off your radio in any location where posted notices instruct you to do so such as health care facilities.
This radio is designed for operation on a 12 Volt battery system. It should not be connected directly to a 24 Volt system. When installing your radio in your vehicle, check that during installation you do not damage any CAUTION wiring or vehicle components that may be hidden around the mounting position. Ensure the installation does not interfere with the operation of the vehicle and meets all regulatory and safety retirements for accessories fitted to your vehicle. For optimum performance, your radio needs to be installed correctly. If you are unsure about how to install your radio, we suggest you have your radio professionally installed by a UHF specialist or Auto electrician. When installing the radio, avoid mounting it close to heaters or air conditioners. Never press the PTT button before connecting the antenna to the radio.

Installation of Your Oricom Radio
Fitting the Controller Speaker Microphone
The controller speaker microphone uses a 6-pin telephone style plug and socket: 1.Position the microphone plug so the plastic flap faces upward,
and insert the plug into the socket until it `clicks’. 2.Gently press the rubber boot into the hole surrounding the
socket so that the slot around the boot fits neatly inside the rim of the entry hole.

Extension Cable Accessory
A. Using microphone extension cable, microphone is installed to socket end, and plug end is installed into transceiver.

This microphone extension cable is typically used where the

transceiver is mounted away from the driver. For example; Under

the seat or behind the center console. This gives the user extra

cable length to the microphone, allowing for more installation

options.

B. Using pass-through extension cable, plug one end into the rear of the pass-through and the other end into the transceiver. Plug the microphone into pass-through.

This pass-through extension cable is used when a UHF pass

through connector (not supplied) is installed in the vehicle dash.

Simply plug the extension cable from the transceiver to the back

of the pass-through connector, then plug your microphone into

the pass-through connector when using the radio. When the

radio is not in use, user can unplug the microphone and store in

a safe place.

Disconnecting the Controller Speaker Microphone It is recommended that the Controller Speaker Microphone be left permanently connected to the radio, but if it must be disconnected, proceed as follows: 1. Lift the rubber boot and the lip of the raised area on the front panel. 2. Ease the rubber boot out of the cable entry hole and slide it along the cable away from the front panel. 3. Identify the plug locking lever, and move the lever towards the plug body. At the same time gently pull the plug from the socket.
Wiring Methods There are two possible wiring configurations for connecting to the vehicles power supply. A. Radio stays ON when the ignition is switched OFF Connect the radio’s negative (black) lead to the vehicle chassis, or directly to the battery’s negative terminal. Connect the radio’s positive (red) lead via the 3 Amp fuse to the battery’s positive terminal. Alternatively, the positive lead could be connected at the fuse box at a point that has DC Power continuously available (preferably the battery side of the ignition switch) via the 3 Amp fuse. B. Radio turns OFF with the ignition switch Connect the radio’s negative (black) lead to the vehicle’s chassis, or directly to the battery’s negative terminal. The radios positive (red) lead should connect to an accessory point in the vehicle’s fuse box via the 3 Amp fuse.
Antenna information The antenna (not supplied) is of critical importance to maximise your output power and receiver sensitivity. A poorly installed, inferior quality antenna, or one not designed for the correct frequency band, will give poor performance. You should only purchase an antenna designed for the 477MHz frequency band.
Antenna installation To obtain maximum performance from the radio, select a high quality antenna and mount it in a good location.
Never press the PTT before connecting an antenna to the radio.
Optional accessories

SPE85 MMM100

External speaker If required, you may install an external (8 ohm, Minimum 5W power) speaker fitted with a 3.5mm plug (not supplied). Depending on the installation, it may be necessary to use an external speaker (not supplied) to give improved volume and clarity. This can be plugged into the external speaker (SP) socket on the rear of the unit.
Magnetic microphone holder
3

Quick Overview of Basic Controls Turning on the Power
Press and hold the Channel selector. At power on, the current applied DC voltage is displayed numerically as shown below. Special over and under voltage detection circuitry protects the radio and warns of excessive voltage conditions by the LCD flashing the 3 backlight colours.
Setting the Volume Turn the channel selector clockwise to adjust the sound level for comfortable reception.
Selecting a channel Press channel selector once. “CH” will appear on the LCD. Select the channel by rotating the channel knob.
Setting the Squelch Level 1. Press channel selector 2 times. The current squelch level is displayed. 2. Select the squelch level by rotating the channel knob. The radio has 16 preset (off to 15) squelch levels, off-Squelch open. 1 – Max. sensitivity (Min. squelch) 15 – Min. sensitivity (Max/Tight squelch)
Note : * If a button is not pressed within 5 seconds, the radio will automatically exit the sub display of “VOL” “CH” and “SQL”.
PTT (Push-To-Talk) button Before transmitting, always listen on the channel to make sure it is not being used by another operator. Pressing the PTT allows audio to be transmitted, by speaking across the front of the controller speaker microphone. TX is indicated by the level bars on the LCD display. To receive, release the PTT button and then TX will disappear on the display. When transmitting, hold the MIC 5 cm from your mouth and speak clearly in normal voice across the front of the mic.
Factory Reset If the radio’s display locks up or stops functioning properly, you might need to reset your UHF radio. Caution: This procedure clears all the information you have stored in your UHF radio. Before you reset your UHF radio, try turning it off and on again. If your UHF radio is still not functioning correctly, you may need to reset the UHF radio. To reset, press and hold monitor button and power on. “Reset” will appear in the display. The radio will then return to standby mode.
4

6.2 Nominal Carrier

Table 1 Nominal Carrier Frequency UHF CB channels and frequencies

Channel
01* 41*
02*
42* 03*
43*
04* 44*
05*
45* 06*
46*
07* 47*
08*
48* 9
49
10 50
11
51 12
52
13 53
14
54 15
55
16 56
17
57 18
58
19 59
20
60

Tx Freq MHZ
476.4250 –
476.4500
476.4750
–
476.5000 –
476.5250
476.5500
–
476.5750 –
476.6000
476.6250 476.6375
476.6500 476.6625 476.6750
476.6875 476.7000 476.7125
476.7250 476.7375 476.7500
476.7625 476.7750 476.7875
476.8000 476.8125 476.8250
476.8375 476.8500 476.8625
476.8750 476.8875 476.9000
476.9125

Rx Freq MHz
476.4250 476.4375 476.4500
476.4625 476.4750 476.4875
476.5000 476.5125 476.5250
476.5375 476.5500 476.5625
476.5750 476.5875 476.6000
476.6125 476.6250 476.6375
476.6500 476.6625 476.6750
476.6875 476.7000 476.7125
476.7250 476.7375 476.7500
476.7625 476.7750 476.7875
476.8000 476.8125 476.8250
476.8375 476.8500 476.8625
476.8750 476.8875 476.9000
476.9125

Channel
21 61
22
62 23
63
24 64
25
65 26
66
27 67
28
68 29
69
30 70
31*
71* 32*
72*
33* 73*
34*
74* 35*
75*
36* 76*
37*
77* 38*
78*
39 79
40
80

Tx Freq MHz
476.9250 —
476.9500
— 476.9750
—
477.0000 477.0125 477.0250
477.0375 477.0500 477.0625
477.0750 477.0875 477.1000
477.1125 477.1250 477.1375
477.1500 477.1625 477.1750
477.1875 477.2000 477.2125
477.2250 477.2375 477.2500
477.2625 477.2750 477.2875
477.3000 477.3125 477.3250
477.3375 477.3500 477.3625
477.3750 477.3875 477.4000
477.4125

Rx Freq MHz
476.9250 —
476.9500
— 476.9750
—
477.0000 477.0125 477.0250
477.0375 477.0500 477.0625
477.0750 477.0875 477.1000
477.1125 477.1250 477.1375
477.1500 477.1625 477.1750
477.2000
–
477.2250 –
477.2500
477.2750
–
477.3000 –
477.3250
477.3500
–
477.3750 477.3875 477.4000
477.4125

* The primary use for these channels is repeater operation using 750 kHz offset. Channels 1-8 inclusive

are used for mobile reception and channels

31-38 for mobile transmission. Note that additional channels 41-48 and

71-78 are also available for repeater operation to supplement channels 1-8 and-31-38 respectively

* Thaes apprpimroavreydubsyethfoerAtChMesAeCcBhRanSnCellasssisLriceepnecaeteinr oApusetrraatliiaonanudsitnheg M75E0D kGHUzRLofinfsNete.wCZheaanlannedls. I1n-8 inclauudssdeivditeifooanrr,eraenupyseeadtdeesrfiogornpaemtreaodtbiorienlep. eraetceerpcthiaonnnaenl md acyhabnenueslesd3f1o-r3s8imfpolrexmoopbeirlaetitornaninsmariesassiownh. eTreheityismnaoyt also

Speech telephony shall be inhibited on these channels. _____________________________________________________________________________________________________________________________________________________ EMCAtTtehcehntoimloegieosf(pNrZo)dLutcdtion Channels 61, 62 and 63 are guard channels and are not available for use.

CShTaRnEnEeTl 5AaDnDdR3E5SS(p- a47ireMdacfoKrelDviuepSlterexert,eGpreeaytLerysn)n,arAeurcekslaenrdv,eNdZas emergencPyhcohnea:n+n6e4ls9 a3n60d0s8h6o2ulFdaxb:e+u64se9d360 0861

oPnOlySTinAaLnAeDmDeRrEgSeSnc- yP.O Box 68 307, Newton, Auckland, New Zealand

E-mail: aucklab@ihug.co.nz

CPTaCgSe S11aonfd2D3 CS wilTl hniostroeppoerrtamteayonnotthbeeserecphroadnunceelds.except in full A list of currently authorised channels can be obtained from the ACMA website in Australia and the MED

website in New Zealand. Channel 11 is a calling channel generally used to call others and channel 40 is the

customary road vehicle channel.

Once contact is established on the calling channel, both stations should move to another unused “SIMPLEX”

channel to allow others to use the calling channel.

Channels 22 and 23 are for Telemetry and Telecommand use, voice communications are not allowed on

these channels by law.

Channel 9 and above are the best choices for general use in Simplex mode.

Express Warranty (Australia)
This Express Warranty is provided by Oricom International Pty Ltd ABN 46 086 116 369, Unit 1, 4 Sovereign Place, South Windsor NSW 2756, herein after referred to as “Oricom”.
Oricom products come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Oricom warrants that the product is free from defects in materials or workmanship during the Express Warranty Period. This Express Warranty does not extend to any product from which the serial number has been removed or was purchased outside of Australia.
Nothing in this Express Warranty excludes, restricts or modifies any condition, warranty, guarantee, implied term, right or remedy pursuant to the Australian Consumer Law and which may not be so excluded, restricted or modified. For such conditions, terms, guarantees and warranties that cannot be excluded, restricted or modified, Oricom limits the remedies available to extent permitted in the relevant legislation.
The Express Warranty Period will be 5 years from the date of purchase of the product evidenced by your dated sales receipt. You are required to provide proof of purchase as a condition of receiving Express Warranty services.
You are entitled to a replacement product or repair of the product at our discretion according to the terms and conditions of this document if your product is found to be faulty within the Express Warranty Period. This Express Warranty extends to the original purchaser only and is not transferable.
Products distributed by Oricom are manufactured using new materials or new and used materials equivalent to new in performance and reliability. Spare parts may be new or equivalent to new. Spare parts are warranted to be free from defects in material or workmanship for thirty (30) days or for the remainder of the Express Warranty Period of the Oricom branded product in which they are installed, whichever is longer. During the Express Warranty Period, Oricom will where possible repair and if not replace the faulty product or part thereof. All component parts removed under this Express Warranty become the property of Oricom. In the unlikely event that your Oricom product has a recurring failure, Oricom may always, subject to the Competition and Consumer Act 2010, at its discretion, elect to provide you with a replacement product of its choosing that is at least equivalent to your product in performance.
No change to the conditions of this Express Warranty is valid unless it is made in writing and signed by an authorised representative of Oricom.
Oricom will not be liable under this Express Warranty, and to the extent permitted by law will not be liable for any defect, loss, damage or injury arising out of or in connection with a: 1. Failure by you to adhere to the warnings and follow the instructions set out in this user guide for the proper installation
and use of the product; 2. Wilful misconduct or deliberate misuse by you of the product; 3. Any external cause beyond our control, including but not limited to power failure, lightning or over voltage; or 4. Modification to the product or services carried out on the product by anyone other than Oricom or Oricom’s authorised
service provider.
How to make a claim under your Express Warranty in Australia
Oricom has a simple warranty process for you to follow: · Please call or email our Customer Support Team, (02) 4574 8888 or support@oricom.com.au. · A Customer Support Team member will verify after troubleshooting with you if your product qualifies under warranty. If
so, they will give you a Product Return Authorisation number. · We will then email or fax a Return Authorisation form and a Repair Notice (if necessary), together with instructions on
how to return the goods for warranty service. Please note that if a Customer Support Team member advises that your product does not qualify for return, this warranty does not apply to your product. Products that are authorised to be returned to Oricom in Australia must include all of the following: · A completed Return Authorisation form · A copy of your Proof of Purchase (please keep your original copy) · The faulty product, including all accessories. Send the approved returns to:
Oricom International Pty Ltd Locked Bag 658 South Windsor NSW 2756 Australia
Please note that this Express Warranty excludes expenses incurred by you in returning any faulty product to us. You must arrange and pay any expenses incurred (including postage, delivery, freight, transportation or insurance of the product) to return the faulty product to us, however, we will arrange delivery of the repaired or replaced faulty product to you.
Important Information Repair Notice
Please be aware that the repair of your goods may result in the loss of any user-generated data (such as stored telephone numbers, text messages and contact information). Please ensure that you have made a copy of any data saved on your goods before sending for repair. Please also be aware that goods presented for repair may be replaced by refurbished goods or parts of the same type rather than being repaired.
6

Documents / Resources

oricom UHF390R 5 Watt UHF CB Radio with Controller Speaker Mic [pdf] User Guide
UHF390R 5 Watt UHF CB Radio with Controller Speaker Mic, UHF390R, 5 Watt UHF CB Radio with Controller Speaker Mic, Radio with Controller Speaker Mic, Controller Speaker Mic, Speaker Mic

References

User Manual

UHF390R 5 Watt UHF CB Radio with Controller Speaker Mic

Specifications

Product Usage Instructions

Installation