Murdock A171-UG-SO Ada Drinking Fountain
STANDARD FEATURES
- Rough-Ins Match Other Manufacturers for Easy Replacement
- Child or Adult ADA Compliant (When Properly Installed)
- Apron and One-Piece Bottom Wrapper is Satin Finish Or
- Gray Powder Coat Finish
- Flexible, Low Flow, Anti-Microbial Anti-Rotation, NonSquirt Bubbler
- 100-Mesh Inlet Strainer
- Hanging Bracket provided
- 9 Volt Sensor Operation
- Lead-Free
SUGGESTED SPECIFICATIONS
Model A171100F-UG-SO is a self-contained, Sensor Operated
Drinking Fountain. The unit shall be activated by a front-mounted 9 Volt Infrared Sensor. Bubbler shall deliver a 0.3 GPM flow, have a Flexible Guard with an integrally designed non-squirt feature, and operate on a water pressure range of 20-105 PSIG. The basin shall be constructed from 304 Stainless Steel and have an Integral Drain.
The cabinet shall be either Galvanized or Galvannealed Steel with a Gray Powder Coat Finish or Stainless Steel with a Satin Finish. Unit shall be certified to Public Law 111- 380 (NO-LEAD) and NSF/ANSI/CAN 61. Fixture meets ADA, ADA Standing Person, and ADA Child requirements when mounted appropriately.
MODEL
(Must Specify)
FLEXIBLE BUBBLER
- A171100F-UG-SO Gray Finish (Standard Shown)
- A171400F-UG-SO Satin Stainless Finish
STAINLESS STEEL BUBBLER
- A171100S-UG-SO Gray Finish
- A171400S-UG-SO Satin Stainless Finish
OPTIONS
(Additional costs may apply.)
- LOGO Customer Specified Logo / Graphics
ACCESSORIES
- (Additional costs may apply. Accessory items are packaged separately.)
- 1 o -WF1 1500-gallon Capacity Water Filter 1 o -WF3 3000-gallon Capacity Water Filter
NOTES
- 1- Refer to the Supplemental Submittal Sheet for details.
Compatible Mounting Support Carrier
Jay R. Smith Mfg. Co. Figure # 0830 https://www.JRSmith.com
- A. 3/8″ O.D. SUPPLY INLET
- B. WASTE OUTLET FOR P-TRAP BY OTHERS FOR
- PROVIDED 1-1/4″ O.D. TAILPIECE
- C. ELECTRICAL SERVICE ROUGH
- D. Ø3/8″ HANGER BRACKET PUNCHING, 6 PLACES
- FOR ANCHORING HARDWARE BY OTHERS
- E. Ø1/4″ PUNCHING, 2 PLACES FOR ANCHORING
- HARDWARE BY OTHERS
- F. DRINKING FOUNTAIN SENSOR
- G. REMOVABLE PLUG FOR BOTTLE FILLER (-BF11 OR -BF12 ONLY)
- H. 1-1/4″ [32] O.D. TAILPIECE FOR P-TRAP BY OTHERS
GENERAL NOTES
- ALL DIMENSIONS ARE IN INCHES [MM]
- ALLOW 4 INCHES [102 MM] MINIMUM CLEARANCE PER SIDE FOR VENTILATION
- DIMENSIONS SHOWN ARE FOR ADA ADULT HEIGHT. ADJUST VERTICAL
- DIMENSIONS AS NECESSARY TO COMPLY WITH FEDERAL, STATE, & LOCAL CODES
- STOP VALVE, P-TRAP, & ELECTRICAL OUTLET NOT SUPPLIED
- IMPORTANT: COOLERS MUST BE ATTACHED TO THE WALL WITH APPROPRIATE
ANCHOR SCREWS
IMPORTANT: Dimensions are shown for reference only. Refer to the product Installation Manual for complete details before Rough-in.All dimensions are subject to manufacturer tolerance of plus orminus 1/4” nominal and subject to change without notice. Murdock assumes no responsibility for the use of void or superseded data. Dimensions may change with the addition of ® optional accessories. Murdock Mfg., Member ® of Morris Group International. Please visit www.murdockmfg.com for the most current specifications.
MURDOCK MFG. 15125 Proctor Avenue City of Industry, CA 91746 USA
Phone 800-453-7465 or 626-333-2543 www.murdockmfg.com
Documents / Resources
 |
murdock A171-UG-SO Ada Drinking Fountain [pdf] Owner's Manual A171-UG-SO Ada Drinking Fountain, A171-UG-SO, Ada Drinking Fountain, Drinking Fountain, Fountain |