MSI 271QRX MPG Series OLED Monitor
Product Information
Specifications
- Product Name: MPG Series OLED Monitor
- Models: MPG 271QRX QD-OLED (3CD7), MPG 321URX QD-OLED (3DD2)
- Revision: V1.0, 2023/12
Getting Started
Package Contents
The package includes the following items:
- Monitor
- Documentation
- Accessories
- Cables
- Quick Start Guide
- Stand
- Stand Base with Screw(s)
- Screw(s) for Wall Mount Bracket(s)
- Power Cord
- Ultra High-Speed HDMITM Cable (Optional)
Important:
- Contact your place of purchase or local distributor if any of the items are damaged or missing.
- Package contents may vary by country.
- The included power cord is exclusively for this monitor and should not be used with other products.
Installing the Monitor Stand
- Leave the monitor in its protective packaging. Align the stand to the monitor groove.
- Push the stand towards the monitor groove until it locks in place.
- Connect the base to the stand and tighten the base screws to secure the base.
- Make sure the stand assembly is properly installed before setting the monitor upright.
Important:
- Place the monitor on a soft, protected surface to avoid scratching the display panel.
- Do not use any sharp objects on the panel.
- The groove for installing the stand bracket can also be used for wall mount. Please contact your dealer for a proper wall-mount kit.
Adjusting the Monitor
This monitor is designed to maximize your viewing comfort with its adjustment capabilities.
Important:
- Avoid touching the display panel when adjusting the monitor.
- Please slightly tilt the monitor before pivoting it.
Monitor Overview
- Cable Routing Hole
- Macro Key – To activate OSD Application.
- Navi Key
- Power Button
- Kensington Lock
- Headphone Jack
- HDMITM Connector (MPG 271QRX QD-OLED) – Supports HDMITM CEC, 2560×1440@360Hz as specified in HDMITM 2.1.
- HDMITM Connector (MPG 321URX QD-OLED) – Supports HDMITM CEC, 3840×2160@240Hz as specified in HDMITM 2.1.
- HDMITM Connector (MPG 271QRX QD-OLED) – Supports 2560×1440@360Hz as specified in HDMITM 2.1.
- HDMITM Connector (MPG 321URX QD-OLED) – Supports 3840×2160@240Hz as specified in HDMITM 2.1.
- DisplayPort (MPG 271QRX QD-OLED) – Supports 2560×1440@360Hz as specified in DisplayPort 1.4.
- DisplayPort (MPG 321URX QD-OLED) – Supports 3840×2160@240Hz as specified in DisplayPort 1.4.
- USB Type-C Port – This port supports DisplayPort Alternate (DP Alt) Mode and up to 20V/4.5A (90W) power delivery.
- USB Type-C Power Delivery – 5V / 3A (15W), 9V / 3A (27W)
Important:
Your USB-C signal source and cable must support DisplayPort Alternate Mode to enable video output to the monitor.
FAQ
- Q: What should I do if any of the package contents are missing or damaged?
A: Contact your place of purchase or local distributor for assistance. - Q: Can I use the included power cord with other products?
A: No, the included power cord is exclusively for this monitor and should not be used with other products. - Q: Can I use the monitor stand for wall mounting?
A: Yes, the groove for installing the stand bracket can also be used for wall mount. Please contact your dealer for the proper wall mount kit. - Q: What should I do if I accidentally touch the display panel while adjusting the monitor?
A: It is recommended to avoid touching the display panel when adjusting the monitor to prevent any damage.
Getting Started
This chapter provides you with the information on hardware setup procedures. While connecting devices, be careful in holding the devices and use a grounded wrist strap to avoid static electricity.
Package Contents
| Monitor | MPG 271QRX QD-OLED
MPG 321URX QD-OLED |
| Documentation | Quick Start Guide |
|
Accessories |
Stand |
| Stand Base with Screw(s) | |
| Screw(s) for Wall Mount Bracket(s) | |
| Power Cord | |
| Cables | Ultra High Speed HDMI™ Cable (Optional) |
Important
- Contact your place of purchase or local distributor if any of the items is damaged or missing.
- Package contents may vary by country.
- The included power cord is exclusively for this monitor and should not be used with other products.
Installing the Monitor Stand
- Leave the monitor in its protective packaging. Align the stand to the monitor groove.
- Push the stand towards the monitor groove until it locks in place.
- Connect the base to the stand and tighten the base screws to secure the base.
- Make sure the stand assembly is properly installed before setting the monitor upright.
Important
- Place the monitor on a soft, protected surface to avoid scratching the display panel.
- Do not use any sharp objects on the panel.
- The groove for installing the stand bracket can also be used for wall mount. Please contact your dealer for a proper wall-mount kit.
Adjusting the Monitor
This monitor is designed to maximize your viewing comfort with its adjustment capabilities.
Important
- Avoid touching the display panel when adjusting the monitor.
- Please slightly tilt the monitor slightly before pivoting it.
MPG 271QRX QD-OLED
MPG 321URX QD-OLED
Monitor Overview
| 1 | Cable Routing Hole |
| 2 | Macro Key
To activate OSD Application. |
| 3 | Navi Key |
| 4 | Power Button |
| 5 | Kensington Lock |
| 6 | Headphone Jack |
| 7 | HDMI™ Connector
(MPG 271QRX QD-OLED) Supports HDMI™ CEC, 2560×1440@360Hz as specified in HDMI™ 2.1. (MPG 321URX QD-OLED) Supports HDMI™ CEC, 3840×2160@240Hz as specified in HDMI™ 2.1. |
| 8 | HDMI™ Connector
(MPG 271QRX QD-OLED) Supports 2560×1440@360Hz as specified in HDMI™ 2.1. (MPG 321URX QD-OLED) Supports 3840×2160@240Hz as specified in HDMI™ 2.1. |
| 9 | DisplayPort
(MPG 271QRX QD-OLED) Supports 2560×1440@360Hz as specified in DisplayPort 1.4. (MPG 321URX QD-OLED) Supports 3840×2160@240Hz as specified in DisplayPort 1.4. |
| 10 | USB Type-C Port USB Type-C
This port supports DisplayPort Alternate Power Delivery (DP Alt) Mode and up to 20V/4.5A (90W) 5V / 3A (15W) power delivery. 9V / 3A (27W) ⚠ Important 12V / 3A (36W) 15V / 3A (45W) Your USB-C signal source and cable must 20V / 3.25A (65W) support DisplayPort Alternate Mode to 20V / 4.5A (90W) enable video output to the monitor. |
| 11 | USB 2.0 Type-B Upstream Port
For USB Upstream Cable. ⚠ Important To Monitor Check the package for USB Upstream Cable and connect it to the PC and monitor. Once this cable is connected, the USB To PC Type-A Downstream Ports on the monitor will be ready for use. |
| 12 | USB 2.0 Type-A Port |
| 13 | Power Jack |
| 14 | Ventilator
The ventilator on the enclosure is used for air convection and to prevent the equipment from overheating. Do not cover the ventilator. Please remove the protective film. |
Connecting the Monitor to the PC
- Turn off your computer.
- Connect the video cable from the monitor to your computer.
- Connect the power cord to the monitor power jack. (Figure A)
- Plug the power cord into the electrical outlet. (Figure B)
- Turn on the monitor. (Figure C)
- Power on the computer and the monitor will auto-detect the signal source.
OSD Setup
This chapter provides you with essential information on OSD Setup.
Important
All information is subject to change without prior notice.
Navi Key
The monitor comes with a Navi Key, a multi-directional control that helps navigate the On-Screen Display (OSD) menu.
Up/Down/Left/Right:
- selecting function menus and items
- adjusting function values
- entering into/exiting from function menus
Press (OK):
- launching the On-Screen Display (OSD)
- entering submenus
- confirming a selection or setting
Hot Key
- Users may enter into preset function menus by moving the Navi Key up, down, left or right when the OSD menu is inactive.
- Users may customize their own Hot Keys to enter into different function menus.
MPG 271QRX QD-OLED
MPG 321URX QD-OLED
Important
The following settings will be grayed out when HDR signals are received:
- Night Vision
- Low Blue Light
- Brightness
- Contrast
- Color Temperature
- Optix Scope
- PIP/PBP
- A.I. Vision
G.I.
| 1st Level Menu | 2nd/3rd Level Menu | Description | |
| KVM | Auto | ∙ Auto allows the monitor to automatically switch between USB input sources, such as keyboards, mice or other USB devices.
∙ Users can also designate Upstream port or USB Type-C as the only USB signal source. |
|
| Upstream | |||
| Type C | |||
| Smart Crosshair | Icon | None | ∙ Through AI algorithm, this function enhances the visibility of in-game crosshair.
∙ Users can select the color and position of the crosshair. |
 |
|||
| Color | White | ||
| Red | |||
| Auto | |||
| Position | |||
| Reset | |||
| Optix Scope | Scope Size | Small | ∙ The center point will zoom in when Optix Scope is enabled.
∙ Smart Crosshair and Optix Scope can be enabled at the same time. ∙ Activating Optix Scope will affect: |
| Medium | |||
| Large | |||
| Scope Ratio | x1.5 | ||
| x2 | |||
| x3 (for MPG 271QRX QD-OLED) | |||
| x4 (for MPG 321URX QD-OLED) | |||
| OFF | |||
| ON | |||
Gaming
| 1st Level Menu | 2nd/3rd Level Menu | Description | |
| Game Mode | Premium Color | ∙ Use Up or Down Button to select and preview mode effects.
∙ Press the OK Button to confirm and apply your mode type. |
|
| User | |||
| FPS | |||
| Racing | |||
| RTS | |||
| RPG | |||
| Night Vision | OFF | ∙ This function optimizes background brightness and is recommended for FPS games. | |
| Normal | |||
| Strong | |||
| Strongest | |||
| A.I. | |||
| A.I. Vision | OFF | ∙ A.I. Vision enhances image quality by optimizing the contrast of images and background brightness.
∙ Activating A.I. Vision will affect: |
|
| ON | |||
| Refresh Rate | Location | Left Top | ∙ Location is adjustable in OSD Menu. Press the OK Button to confirm and apply your Refresh Rate Location.
∙ This monitor follows and works at the Operating System’s preset Screen Refresh Rate. |
| Right Top | |||
| Left Bottom | |||
| Right Bottom | |||
| Customize | |||
| OFF | |||
| ON | |||
| Alarm Clock | Location | Left Top | ∙ After setting the time, press the OK Button to activate the timer.
∙ Users have to manually restore their preset Alarm Clock after any AC power loss and reconnection. |
| Right Top | |||
| Left Bottom | |||
| Right Bottom | |||
| Customize | |||
| OFF | |||
| 15:00 | 00:01 ~ 99:59 | ||
| 30:00 | |||
| 45:00 | |||
| 60:00 | |||
| 1st Level Menu | 2nd/3rd Level Menu | Description |
| Adaptive-Sync | OFF | ∙ Adaptive-Sync prevents screen tearing.
∙ Activating Adaptive-Sync will affect: |
| ON |
Professional
| 1st Level Menu | 2nd Level Menu | Description |
| Pro Mode | Eco | ∙ Use Up or Down Button to select and preview mode effects.
∙ Press the OK Button to confirm and apply your mode type. ∙ The default setting “Eco” mode meets the requirements of TÜV Rheinland’s “Low Blue Light” standard. ∙ Activating sRGB, Adobe RGB, and Display P3 will affect: |
| User | ||
| Anti-Blue | ||
| Movie | ||
| Office | ||
| sRGB | ||
| Adobe RGB | ||
| Display P3 | ||
| Low Blue Light | OFF | ∙ Low Blue Light protects your eyes against blue light. When enabled, Low Blue Light adjusts the screen color temperature to a more yellow glow.
∙ When Pro Mode is set to Anti-Blue, it is mandatory to enable Low Blue Light. ∙ This monitor is a Low Blue Light monitor which will decrease the blue light emitted without adjusting the OSD settings. |
| ON | ||
| Image Enhancement | OFF | ∙ Image Enhancement enhances image edges to improve their acutance. |
| Weak | ||
| Medium | ||
| Strong | ||
| Strongest |
Image
| 1st Level Menu | 2nd/3rd Level Menu | Description | |
| Brightness | 0-100 | ∙ Properly adjust Brightness according to the surrounding lighting. | |
| Contrast | 0-100 | ∙ Properly adjust Contrast to relax your eyes. | |
| Sharpness | 0-5 | ∙ Sharpness improves clarity and details of images. | |
| Color Temperature | Cool | ∙ Use Up or Down Button to select and preview mode effects.
∙ Press the OK Button to confirm and apply your mode type. ∙ Users can adjust Color Temperature in Customization mode. |
|
| Normal | |||
| Warm | |||
| Customization | R (0-100) | ||
| G (0-100) | |||
| B (0-100) | |||
| Screen Size | Auto | ∙ Users can adjust Screen Size in any mode, any resolution and any screen refresh rate.
∙ Activating Screen Size will affect: |
|
| 4:3 | |||
| 16:9 | |||
| 16:10 | |||
| 1:1 | |||
| DisplayHDR | True Black 400 | ∙ Users can set the DisplayHDR to True Black 400 or Peak 1000 nits. | |
| Peak 1000 nits | |||
Input Source
| 1st Level Menu | 2nd Level Menu | Description |
| HDMI™ 1 | ∙ Users can adjust Input Source in any mode. | |
| HDMI™ 2 | ||
| DP | ||
| Type C | ||
| Auto Scan | OFF | ∙ Users can use the Navi Key to select Input Source at below status:
• While “Auto Scan” is set to “OFF” with the monitor at power saving mode; • While “No Signal” message box is shown on the monitor. |
| ON | ||
PIP/PBP
| 1st Level Menu | 2nd/3rd Level Menu | Description | |
| OFF | ∙ PIP (Picture in Picture) allows users to simultaneously display multiple video sources on one screen. One program is displayed on the full screen at the same time as one or more other programs are displayed in inset windows.
∙ PBP (Picture by Picture) is a similar feature that displays two input sources side-by-side on the screen. ∙ Display Switch allows users to switch between primary and secondary input sources. ∙ If there is only one signal input, the Display Switch and Audio Switch will be grayed out. ∙ Users can adjust the ratio of window division by switching mode 1/ 2. ∙ Activating PIP/PBP will affect: |
||
| PIP | Source | HDMI™ 1 | |
| HDMI™ 2 | |||
| DP | |||
| Type C | |||
| PIP Size | Small | ||
| Medium | |||
| Large | |||
| Location | Left Top | ||
| Right Top | |||
| Left Bottom | |||
| Right Bottom | |||
| Customize | |||
| Display Switch | |||
| Audio Switch | |||
| PBP | Mode 1 | ||
| Mode 2 | |||
| Customize | |||
| Source 1 | HDMI™ 1 | ||
| HDMI™ 2 | |||
| DP | |||
| Type C | |||
| Source 2 | HDMI™ 1 | ||
| HDMI™ 2 | |||
| DP | |||
| Type C | |||
| Display Switch | |||
| Audio Switch | |||
Navi Key
| 1st Level Menu | 2nd Level Menu | Description |
| Up Down Left Right | OFF | ∙ All Navi Key items can be adjusted via OSD Menus. |
| Brightness | ||
| Game Mode | ||
| Smart Crosshair | ||
| Alarm Clock | ||
| Input Source | ||
| PIP/PBP Mode | ||
| Refresh Rate | ||
| Info. On Screen | ||
| Night Vision | ||
| Optix Scope | ||
| KVM |
Settings
| 1st Level Menu | 2nd Level Menu | Description |
| Language | 繁體中文 | ∙ Users have to press the OK Button to confirm and apply the Language setting.
∙ Language is an independent setting. Users’ own language setting will override the factory default. When users set Reset to Yes, Language will not be changed. |
| English | ||
| Français | ||
| Deutsch | ||
| Italiano | ||
| Español | ||
| 한국어 | ||
| 日本語 | ||
| Русский | ||
| Português | ||
| 简体中文 | ||
| Bahasa Indonesia | ||
| Türkçe | ||
| (More languages coming soon) | ||
| Transparency | 0~5 | ∙ Users can adjust Transparency in any mode. |
| OSD Time Out | 5~30s | ∙ Users can adjust OSD Time Out in any mode. |
| RGB LED | OFF | ∙ Users can adjust RGB LED to ON or OFF. |
| MSI – Mystic Light | ||
| RGB Brightness |
| 1st Level Menu | 2nd Level Menu | Description |
| Power Button | OFF | ∙ When set to OFF, users can press the power button to turn off the monitor. |
| Standby | ∙ When set to Standby, users can press the power button to turn off the panel and backlight. | |
| Info. On Screen | OFF | ∙ The information of the monitor status will be shown on the right side of the screen. |
| ON | ||
| HDMI™ CEC | OFF | ∙ HDMI™ CEC (Consumer Electronics Control) supports Sony PlayStation®, Nintendo® Switch™, Xbox Series X|S consoles and various audio-visual devices that are CEC-capable.
∙ If HDMI™ CEC is set to ON: • The monitor will automatically power on when the CEC device is turned on. • The CEC device will enter power saving mode when the monitor is turned off. • When Sony PlayStation®, Nintendo® Switch™, or Xbox Series X|S console is connected, Game Mode and Pro Mode will be automatically set to default modes and can be adjusted to users’ preferred modes later. |
| ON | ||
| Type C PD Charge | OFF | ∙ This function enables users to charge their devices through a USB Type-C connector. |
| ON | ||
| Reset | YES | ∙ Users can Reset and restore settings to the original OSD Default in any mode. |
| NO |
MSI OLED Care
| 1st Level Menu | 2nd/3rd Level Menu | Description |
| Pixel Shift | Slow | ∙ Pixel Shift moves the pixels of your screen at regular intervals to reduce the possibility of screen burn-in or image retention. |
| Normal | ||
| Fast | ||
| Panel Protect | ∙ To maintain panel image quality, panel protect (short time) function will automatically activate when monitoring over 4 hours.
∙ This protection function may take several minutes to complete. ∙ The power indicator will blink orange color until the process is done. ∙ During process execution, please do not unplug the power cord from the monitor. ∙ During the process of executing, press the power button again to cancel this function. |
|
| 1st Level Menu | 2nd/3rd Level Menu | Description | |
| Protect Notice | Auto | ∙ When set to Auto, Protect Notice will pop up when the panel exceeds 4 hours of cumulative usage.
∙ When set to Usage 16 hrs, Protect Notice will pop up when the panel exceeds 16 hours of cumulative usage. ∙ When Panel Protect is interrupted, Protect Notice will pop up upon the next power-up. |
|
| Usage 16 hrs | |||
| Static Screen Detection | OFF | ∙ If Static Screen Detection is set to ON:
• When detecting static visuals over long periods, the monitor reduces brightness to prevent screen burn-in. • Once moving visuals, the monitor restores its previous brightness setting. |
|
| ON | |||
| Starting in | 50 Sec | ∙ Starting in detects the time a static image remains on the screen. | |
| 100 Sec | |||
| Time required | 120 Sec | ∙ Time required specifies the time for brightness reduction after detecting a static image for 50/100 seconds.
∙ The brightness reduction level depends on the setting of the Reducing Level. |
|
| 240 Sec | |||
| Reducing Level | 1-7 | ∙ Users can select a level for brightness reduction.
∙ Reducing effect depends on Brightness/ DisplayHDR setting. |
|
| Multi Logo Detection | OFF | ∙ This function helps prevent image image-sticking phenomenon. When set to ON, brightness reduction of multi-logo areas will kick in if logos are detected. | |
| ON | |||
| Reducing Level | 1-2 | ∙ Users can select a level for brightness reduction.
• 1 : 10% reduction • 2 : 20% reduction ∙ Reducing effect depends on Brightness/ DisplayHDR setting. |
|
| Taskbar Detection | OFF | ∙ This function helps prevent image image-sticking phenomenon. When set to ON, brightness reduction of taskbar areas will kick in if taskbars are detected. | |
| ON | |||
| Reducing Level | 1-3 | ∙ Users can select a level for brightness reduction.
• 1: 10% reduction • 2: 15% reduction • 3: 20% reduction ∙ Reducing effect depends on Brightness/ DisplayHDR setting. |
|
| 1st Level Menu | 2nd/3rd Level Menu | Description | |
| Boundary Detection | OFF | ∙ This function helps prevent image image-sticking phenomenon. When set to ON, brightness reduction of boundary areas will kick in if boundaries, such as letters, pillars, and vertical
lines are detected. |
|
| ON | |||
| Reducing Level | 1-3 | ∙ Users can select a level for brightness reduction.
• 1 : 10% reduction • 2 : 15% reduction • 3 : 20% reduction ∙ Reducing effect depends on Brightness/ DisplayHDR setting. |
|
| OLED Panel Info. | ∙ This field shows the information of MSI OLED
Care. |
||
* HDMI™ VRR (Variable Refresh Rate) synchronizes with Adaptive-Sync (ON/ OFF). For VRR ON/OFF status, please check Adaptive-Sync.
** When VRR is set to ON, the monitor scaler will detect whether the graphics card is sending VRR content.
Specifications
| Monitor | MPG 271QRX QD-OLED | MPG 321URX QD-OLED |
| Size | 26.5 inch | 31.5 inch |
| Curvature | Flat | |
| Panel Type | QD-OLED | |
| Resolution | 2560×1440 (WQHD) | 3840×2160 (UHD) |
| Aspect Ratio | 16:9 | |
| Brightness | ∙ Typical SDR: 250 nits
∙ Peak HDR: 1000 nits |
|
| Contrast Ratio | 1500000:1 | |
| Refresh Rate | 360Hz | 240Hz |
| Response Time | 0.03ms (GTG) | |
|
I/O |
∙ Headphone Jack x1
∙ DisplayPort x1 ∙ HDMI™ Connector x2 ∙ USB Type-C Port x1 ∙ USB 2.0 Type-B Upstream Port x1 ∙ USB 2.0 Type-A Port x2 |
|
| View Angles | 178°(H) , 178°(V) | |
| DCI-P3*/ sRGB | 99%/ 138% | |
| Surface Treatment | Anti-Reflection | |
| Display Colors | 1.07B (10 bits) | |
| Monitor Power Options | 100~240Vac, 50/60Hz,
2.7A |
100~240Vac, 50/60Hz,
3.1A |
|
Power Consumption (Typical) |
Power On < 205W
Standby < 0.5W Power Off < 0.3W |
Power On < 270W
Standby < 0.5W Power Off < 0.3W |
| Adjustment (Height) | 0 ~ 110mm | |
| Adjustment (Tilt) | -5° ~ 20° | -5° ~ 15° |
| Adjustment (Swivel) | -30° ~ 30° | -30° ~ 30° |
| Adjustment (Pivot) | -90° ~ 90° | -10° ~ 10° |
| Kensington Lock | Yes | |
| Monitor | MPG 271QRX QD-OLED | MPG 321URX QD-OLED | |
|
VESA Mounting |
∙ Plate Type: 100 x 100 mm
∙ Screw Type: M4 x 10 mm • Thread Diameter: 4 mm • Thread Pitch: 0.7 mm • Thread Length: 10 mm |
||
| Dimension (W x H x D) | 610 x 422 x 242 mm | 718 x 483 x 242 mm | |
| Weight | Net | 8.3 kg | 9.6 kg |
| Gross | 10.9 kg | 12.3 kg | |
|
Environment |
Operating |
∙ Temperature: 0℃ to 40℃
∙ Humidity: 20% to 90%, non-condensing ∙ Altitude: 0 ~ 5000m |
|
| Storage | ∙ Temperature: -20℃ to 60℃
∙ Humidity: 10% to 90%, non-condensing |
||
Preset Display Modes
Important
All information is subject to change without prior notice.
MPG 271QRX QD-OLED
| Standard | Resolution | Standard Mode | |||
| HDMI™ | DP | USB-C | |||
| QHD | 2560×1440 | @60Hz | V | V | V |
| @120Hz | V | V | V | ||
| @240Hz | V | V | V | ||
| @360Hz | V | V | V | ||
| Video Timing Resolution | 720P | V | V | V | |
| 1080P @60Hz | V | V | V | ||
| 1080P @120Hz | V | V | V | ||
| 2160P @30Hz | V | ||||
| 2160P @60Hz | V | ||||
| 2160P @120Hz | V | ||||
| HDMI™ VRR for PS5 | V | ||||
| Standard | Resolution | PIP Mode (Not Support HDR) | |||
| HDMI™ | DP | USB-C | |||
| QHD | 2560×1440 | @60Hz | V | V | V |
| @120Hz | V | V | V | ||
| Video Timing Resolution | 720P | V | V | V | |
| 1080P @60Hz | V | V | V | ||
| 2160P @30Hz | V | V | |||
| 2160P @50Hz | V | V | |||
| 2160P @60Hz | V | V | |||
| Standard | Resolution | PBP Mode 1 (Not Support HDR) | |||
| HDMI™ | DP | USB-C | |||
| Video Timing Resolution | 720P | V | V | V | |
| Used for PBP Full Screen | 1920×1440 | @60Hz | V | V | V |
| 640×1440 | @60Hz | V | V | V | |
| Standard | Resolution | PBP Mode 2/ Customize (Not Support HDR) | |||
| HDMI™ | DP | USB-C | |||
| Video Timing Resolution | 720P | V | V | V | |
| Used for PBP Full Screen | 1280×1440 | @60Hz | V | V | V |
|
Standard |
Resolution |
Screen Size 16:10 (Not
Support HDR) |
|||
| HDMI™ | DP | USB-C | |||
| QHD+ | 2560×1600 | @60Hz | V | V | V |
| @120Hz | V | V | V | ||
| @240Hz | V | V | V | ||
| @360Hz | V | V | V | ||
* HDMI™ VRR (Variable Refresh Rate) synchronizes with Adaptive-Sync (ON/ OFF).
MPG 321URX QD-OLED
| Standard | Resolution | Standard Mode | |||
| HDMI™ | DP | USB-C | |||
| QHD | 2560×1440 | @60Hz | V | V | V |
| @120Hz | V | V | V | ||
| UHD | 3840×2160 | @60Hz | V | V | V |
| @120Hz | V | V | |||
| @180Hz | V | V | V | ||
| @240Hz | V | V | V | ||
| Video Timing Resolution | 720P | V | V | V | |
| 1080P @60Hz | V | V | V | ||
| 1080P @120Hz | V | V | V | ||
| 2160P @30Hz | V | ||||
| 2160P @60Hz | V | ||||
| 2160P @120Hz | V | ||||
| HDMI™ VRR for PS5 | V | ||||
| Standard | Resolution | PIP Mode (Not Support HDR) | |||
| HDMI™ | DP | USB-C | |||
| QHD | 2560×1440 | @60Hz | V | V | V |
| @120Hz | V | V | V | ||
| UHD | 3840×2160 | @60Hz | V | V | V |
| @120Hz | V | V | V | ||
| Video Timing Resolution | 720P | V | V | V | |
| 1080P @60Hz | V | V | V | ||
| 1080P @120Hz | V | V | V | ||
| 2160P @30Hz | V | V | |||
| 2160P @50Hz | V | V | |||
| 2160P @60Hz | V | V | |||
| 2160P @120Hz | V | V | V | ||
| Standard | Resolution | PBP Mode 1 (Not Support HDR) | |||
| HDMI™ | DP | USB-C | |||
| Video Timing Resolution | 720P | V | V | V | |
| Used for PBP Full Screen | 960×2160 | @60Hz | V | V | V |
| 2880×2160 | @60Hz | V | V | V | |
| Standard | Resolution | PBP Mode 2/ Customize (Not Support HDR) | |||
| HDMI™ | DP | USB-C | |||
| Video Timing Resolution | 720P | V | V | V | |
| Used for PBP Full Screen | 1920×2160 | @60Hz | V | V | V |
| Standard | Resolution | Screen Size 16:10 (Not Support HDR) | |||
| HDMI™ | DP | USB-C | |||
| QHD+ | 2560×1600 | @60Hz | V | V | V |
| @120Hz | V | V | V | ||
| @144Hz | V | V | V | ||
| @240Hz | V | V | V | ||
Troubleshooting
The power LED is off.
- Press the monitor power button again.
- Check if the monitor power cable is properly connected.
No image.
- Check if the computer graphics card is properly installed.
- Check if the computer and monitor are connected to electrical outlets and are turned on.
- Check if the monitor signal cable is properly connected.
- The computer may be in Standby mode. Press any key to activate the monitor.
The screen image is not properly sized or centered.
- Refer to Preset Display Modes to set the computer to a setting suitable for the monitor to display.
No Plug & Play.
- Check if the monitor power cable is properly connected.
- Check if the monitor signal cable is properly connected.
- Check if the computer and graphics card are Plug & Play compatible.
The icons, font or screen are fuzzy, blurry or have color problems.
- Avoid using any video extension cables.
- Adjust brightness and contrast.
- Adjust RGB color or tune color temperature.
- Check if the monitor signal cable is properly connected.
- Check for bent pins on the signal cable connector.
The monitor starts flickering or shows waves.
- Change the refresh rate to match the capabilities of your monitor.
- Update your graphics card drivers.
- Keep the monitor away from electrical devices that may cause electromagnetic interference (EMI).
Safety Instructions
- Read the safety instructions carefully and thoroughly.
- All cautions and warnings on the device or User Guide should be noted.
- Refer servicing to qualified personnel only.
Power
- Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 100~240V before connecting the device to the power outlet.
- If the power cord comes with a 3-pin plug, do not disable the protective earth pin from the plug. The device must be connected to an earthed main socket outlet.
- Please confirm the power distribution system in the installation site shall provide the circuit breaker rated 120/240V, 20A (maximum).
- Always disconnect the power cord or switch the wall socket off if the device is left unused for a certain time to achieve zero energy consumption.
- Place the power cord in a way that people are unlikely to step on it. Do not place anything on the power cord.
- If this device comes with an adapter, use only the MSI-provided AC adapter approved for use with this device
Environment
- To reduce the possibility of heat-related injuries or of overheating the device, do not place the device on a soft, unsteady surface or obstruct its air ventilators.
- Use this device only on a hard, flat, and steady surface.
- To prevent the device from tipping over, secure the device to a desk, wall or fixed object with an anti-tip fastener that helps to properly support the device and keep it safe in place.
- To prevent fire or shock hazards, keep this device away from humidity and high temperatures.
- Do not leave the device in an unconditioned environment with a storage temperature above 60℃ or below -20℃, which may damage the device.
- The maximum operating temperature is around 40℃.
- When cleaning the device, be sure to remove the power plug. Use a piece of soft cloth rather than industrial chemicals to clean the device. Never pour any liquid into the opening; that could damage the device or cause electric shock.
- Always keep strong magnetic or electrical objects away from the device.
- If any of the following situations arises, get the device checked by service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the device.
- The device has been exposed to moisture.
- The device does not work well or you can not get it working according to the User Guide.
- The device has dropped and damaged.
- The device has obvious signs of breakage.
TÜV Rheinland Certification
TÜV Rheinland Low Blue Light Certification
Blue light has been shown to cause eye fatigue and discomfort. MSI now offers monitors with TÜV Rheinland Low Blue Light certification to ensure users’ eye comfort and well-being. Please follow the instructions below to reduce the symptoms from extended exposure to the screen and blue light.
- Place the screen 20 – 28 inches (50 – 70 cm) away from your eyes and a little below eye level.
- Consciously blinking the eyes every now and then will help to reduce eye strain after extended screen time.
- Take breaks for 20 minutes every 2 hours.
- Look away from the screen and gaze at a distant object for at least 20 seconds during breaks.
- Make stretches to relieve body fatigue or pain during breaks.
TÜV Rheinland Flicker Free Certification
- TÜV Rheinland has tested this product to ascertain whether the display produces visible and invisible flicker for the human eye and therefore strains the eyes of users.
- TÜV Rheinland has defined a catalog of tests, which sets out minimum standards at various frequency ranges. The test catalog is based on internationally applicable standards or standards common within the industry and exceeds these requirements.
- The product has been tested in the laboratory according to these criteria.
- The keyword “Flicker Free” confirms that the device has no visible and invisible flicker defined in this standard within the range of 0 – 3000 Hz under various brightness settings.
- The display will not support Flicker-Free when Anti Motion Blur/MPRT is enabled. (The availability of Anti Motion Blur/MPRT varies by product.)
Regulatory Notices
CE Conformity
This device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), ErP Directive (2009/125/EC) and RoHS directive (2011/65/EU). This product has been tested and found to comply with the harmonized standards for Information Technology Equipment published under Directives of Official Journal of the European Union.
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used under the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the measures listed below:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/television technician for help.
Notice 1
- The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Notice 2
- Shielded interface cables and AC power cord, if any, must be used to comply with the emission limits.
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
MSI Computer Corp.
901 Canada Court, City of Industry, CA 91748, USA
626-913-0828 www.msi.com
WEEE Statement
Under the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2012/19/EU, products of “electrical and electronic equipment” cannot be discarded as municipal waste anymore and manufacturers of covered electronic equipment will be obligated to take back such products at the end of their useful life.
Chemical Substances Information
In compliance with chemical substances regulations, such as the EU REACH Regulation (Regulation EC No. 1907/2006 of the European Parliament and the Council), MSI provides information of chemical substances in products at: https://csr.msi.com/global/index
RoHS Statement
Japan JIS C 0950 Material Declaration
A Japanese regulatory requirement, defined by specification JIS C 0950, mandates that manufacturers provide material declarations for certain categories of electronic products offered for sale after July 1, 2006.
https://csr.msi.com/global/Japan-JIS-C-0950-Material-Declarations
India RoHS
This product complies with the “India E-waste (Management and Handling) Rule 2016” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.
Turkey EEE Regulation
Conforms to the EEE Regulations of the Republic Of Turkey
Ukraine Restriction of Hazardous Substances
The equipment complies with the requirements of the Technical Regulation, approved by the Resolution of Cabinet of the Ministry of Ukraine as of 10 March 2017, № 139, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment.
Vietnam RoHS
As from December 1, 2012, all products manufactured by MSI comply with Circular 30/2011/TT-BCT temporarily regulating the permitted limits for many hazardous substances in electronic and electric products.
Green Product Features
- Reduced energy consumption during use and stand-by
- Limited use of substances harmful to the environment and health
- Easily dismantled and recycled
- Reduced use of natural resources by encouraging recycling
- Extended product lifetime through easy upgrades
- Reduced solid waste production through a take-back policy
Environmental Policy
- The product has been designed to enable proper reuse of parts and recycling and should not be thrown away at its end of life.
- Users should contact the local authorized point of collection for recycling and disposing of their end-of-life products.
- Visit the MSI website and locate a nearby distributor for further recycling information.
- Users may also reach us at gpcontdev@msi.com for information regarding proper disposal, take-back, recycling, and disassembly of MSI products.
Warning!
Overuse of screens is likely to affect eyesight.
Recommendations:
- Take a 10-minute break for every 30 minutes of screen time.
- Children under 2 years of age should have no screen time. For children aged 2 years and over, screen time should be limited to less than one hour per day.
Copyright and Trademarks Notice
Copyright © Micro-Star Int’l Co., Ltd. All rights reserved. The MSI logo used is a registered trademark of Micro-Star Int’l Co., Ltd. All other marks and names mentioned may be trademarks of their respective owners. No warranty as to accuracy or completeness is expressed or implied. MSI reserves the right to make changes to this document without prior notice.
The terms HDMI™, HDMI™ High-Definition Multimedia Interface, HDMI™ Trade dress, and the HDMI™ Logos are trademarks or registered trademarks of HDMI™ Licensing Administrator, Inc.
Technical Support
If a problem arises with your product and no solution can be obtained from the user’s manual, please contact your place of purchase or local distributor. Alternatively, please visit https://www.msi.com/support/ for further guidance.
Documents / Resources
 |
MSI 271QRX MPG Series OLED Monitor [pdf] User Guide 271QRX MPG Series OLED Monitor, 271QRX, MPG Series OLED Monitor, Series OLED Monitor, OLED Monitor, Monitor |
