Megacom Catchmon Go Plus Auto Catcher Accessory
INTRODUCTION
- Enhanced Bluetooth design
Automatically collect and capture, and earn stardust, candy, and experience. - Always on 600 hours on standby
With up to 600 hours of standby power, no need to recharge - One-tou” reconnection
Only need to touch your phone to reconnect CATCHMON GO
How to connect Catchmon GO with your phone for the first time
Insert two AAA batteries and turn on Catchmon GO. The LED will flash green several times
- Turn on Bluetooth in the phone
- Go to Pokemon Go and click “Main Menu”
- Click “Settings” in the upper right corner
- Go to the bottom and click “Pokémon Go Plus” Available devices are shown below.
- Click on the pokemon go plus on phone to start connecting with Catchmon GO
- After successful connection, available devices on the app will light up like a graph.
- After successful connection, available devices on the app will light up like a graph.
- LED will be purple and flashing when Catchmon GO is connected.
If Catchmon GO had successfully connected with the phone before but the signal is lost, LED will be blue and flashing.
To reconnect, simply click Go Plus icon at top right in the phone app map. (Purple light flashing if connection successful)
To connect with new phones, first unpair the previous Catchmon GO connection. Methods are indicated as follows.
Function and light description
- Press Catchmon GO button to switch between the different light functions.
- Press once and go from blue light > green light> purple light in order.
- Switch to the desired light option, then set up based on the instructions below.
Blue light: to unpair Catchmon GO Bluetooth
Catchment GO with a new phone, first unpair previous
connection: Pressing LED to blue light, long press again for 3 sec to unpair.
When unpairing, LED will be blue and yellow flashing for 30 sec.
- Unpairing successful: green light flashes
- Unpairing unsuccessful: red light flashes
Greenlight: notification sound switch
- Greenlight: sound on
- Green breathing light: sound off
- In green light display, press 3s to switch on/off notification sound setting.
- Turned on: green light flashes
- Turned off: red light flashes
Purple light: vibration switch
- Purple light: vibration on
- Purple breathing light: vibration off
- In purple light display, press for 3s again to switch on/off the vibration setting.
- Turned on successful: purple light flashes
- Turned off successful: red light flashes
When you turn on Catchmon GO, press the button first and turn on the power itch together, both sound and vibration functions will be turned off.
Catchmon tips
- If bag is full and cannot collect items from Pokestop, first deactivate “Nearby Pokestop” notification in Go Plus setting menu.
- If out of red Pokebals and temporarily cannot capture, first deactivate “Nearby Pokémon” notification in Go Plus setting menu.
Light, sound, and vibration description
Additional Instructions
Catchmon Go consumes very little power and has power-saving and sleep mode features.
Pokemon app will automatically disconnect from Catchmon every hour. If not reconnected after 10min, Catchmon Go will go into sleep mode.
Players can press the Go Plus connection icon in app anytime and automatically call up Catchmon Go to reconnect. When changing batteries, Catchmon Go will retain all settings in memory so reset is not necessary.
f unable to connect with Catchmon Go, please try the following:
- Delete Pokemon Go Plus Bluetooth setting in the phone.
- Go to game settings and disconnect Pokemon Go Plus.
- Unpair Bluetooth setting in Catchmon (Press blue LED 3 sec)
- Turn off game and restart it.
- Connect Catchmon GO and Pokemon Go App as the first time.
P.S: Pokemon Go App, Android, and iOS system upgrades may cause Catchmon Go to not connect. Multiple Catchmons in one place will also cause Bluetooth interference in phone and cause disconnection.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions
- This device may not cause harmful interference, and (2) this device must accept any interference recelved, including interference that may cause undesired operation.
Non-modification Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements,
The device can be used in portable exposure conditions without restriction.
Compatible with iphone 6s or higher devices with OS Ver: 11 or higher installed.
compatible with Android devices with 2 GB RAM or more. Bluetooth Smart (Bluetooth Ver. 4.0 or higher) capability and Android Ver. 7.0 or higher installed.
Copyright Sperry Corporation All Rights Reserved.
Catchmon Go is the trademark of Sperry Corporation. Pokemon/ PokemonGo / Pokemon Go Plus are the trademarks of Nintendo. The other trademark names are the used marks, trademarks or registered trademarks of the corresponding companies. This Product is not sponsored, endorsed, or approved by Nintendo, the ThePokémon Company Or Niantic.
Made in Taiwan
SPERRY CORPORATION
369, Fu-Shin North Road, Taipei Taiwan
www.dualcatchmon.com
Brand: MEGACOM
Model No: CG-1688
Power Rating: DC 3V, AAA batteries*2 (not Included)
FREQUENTLY ASKED QUESTION
Do they remove the capture time delay function from this model? it was on dual catchmon and it’s slower because of the delay.
It’s slower probably because it’s focusing on two inputs & not one. It doesn’t have a speed setting.
By John on August 11, 2020
It means you don’t have to turn the egg back on to reconnect. It will auto disconnect after an hour. You’ll have to reconnect through Pogo.
On settings in-game, you can select “Pokémon” or “Stops” from the pogo + section in settings. once you deselect Pokémon it will stop trying to catch them and only spin stops.
Yup! It lets you know if it’s new to your account based on how the colors change
Google thier webite. Try to reset the device & disconnect it from your bluetooth. Then pair it again.
No. The code was made open source so companies could make things like this. You must realize that Nintendo is very powerful and finicky about their trademarks. If they didn’t want them to be sold, you would not find them on Amazon.
You can turn off the “phone screen” or let the Game APP works on the background.
our device will let the Game keeps counting your moving for hatching the egg.
Try disconnecting on the PoGo game in the settings and than resetting
Yeah, that’s the phone I use. It works as intended and will connect properly. Keep in mind as a side note though, the plastic on this is cheap and breaks easily so keep it somewhere safe if you get it. The on switch comes off easily as well.
hi, you can turn off the “screen” (not the app) or let the APP on the background. it will auto catch, auto collect and hatch the egg.
