45W PWM Output LED Driver
ODLV-45 series
User’s Manual
http://www.meanwell.com.cn/Upload/PDF/LED_EN.pdf
Features
- Constant Voltage PWM style output with frequency 1KHz
- Plastic housing with class Il design
- Built-in active PFC function
- No load power consumption<0.5W (Blank-Type)
- IP67 rating for indoor or outdoor installations
- Function options: 2 in 1 dimming (dim-to-off); Auxiliary DC output
- 3 years warranty
Applications
- LED strip lighting
- Indoor LED lighting
- LED decorative lighting
- LED architecture lighting
Description
ODLV-45 series is a45W AC/DC LED driver featuring the constant voltage mode PWM style output design. ODLV-45 operates from 90~295VAC and offers models with different rated voltage ranging between 12V and 60V. Thanks to the high efficiency up to 90%, with the fanless design, the entire series is able to operate for -20°C ~+85C case temperature under free air convection. The design of plastic housing and IP67 ingress protection level allows this series to fit indoor wet applications. ODLV-45is equipped with various function options, such as dimming methodologies, so as to provide the design flexibility for LED lighting system.
Model Encoding
| Type | Function | Note |
| Blank | 2 in 1 dimming (0~10VDC and 10V PWM) | ln Stock |
| A | 2 in 1 dimming and Auxiliary DC output | ln Stock |
SPECIFICATION
| MODEL | ODLV-45 -12 | ODLV-45 -24 | ODLV-45 -36 | ODLV-45 -48 | ODLV-45 -60 | |
| OUTPUT | DC VOLTAGE | 12V | 24V | 36V | 48V | 60V |
| RATED CURRENT | 3.0A | 1.88A | 1.25A | 0.94A | 0.75A | |
| RATED POWER | 36W | 45.12W | 45W | 45.12W | 45W | |
| DIMMING RANGE | 0~100% | |||||
| VOLTAGE TOLERANCE | ±10% | |||||
| PWM FREQUENCY (Typ.) | 1KHz(±20%) | |||||
| SETUP TIME Note.3 | 500ms / 230VAC 1200ms/115VAC | |||||
| AUXILIARY DC OUTPUT Note.4 | Nominal 12V(deviation 11.4~12.6)@50mA for A-Type only | |||||
| INPUT | VOLTAGE RANGE Note.2 | 90 ~ 295VAC (Please refer to “STATIC CHARACTERISTIC” section) |
||||
| FREQUENCY RANGE | 47 ~ 63Hz | |||||
|
POWER FACTOR (Typ.) |
PF>0.95/115VAC, PF>0.92/230VAC, PF>0.9/277VAC@full load (Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section) | |||||
| TOTAL HARMONIC DISTORTION | THD< 20%(@load≧60%/115VAC,230VAC; @load≧75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION” section) | |||||
| EFFICIENCY (Typ.) | 84% | 86% | 88% | 88% | 90% | |
| AC CURRENT (Typ.) | 0.6A / 115VAC 0.4A / 230VAC 0.3A / 277VAC | |||||
| INRUSH CURRENT(Typ.) | COLD START 30A(twidth=150μs measured at 50% Ipeak) at 230VAC; Per NEMA 410 | |||||
| MAX. No. of PSUs on 16A CIRCUIT BREAKER | 32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC | |||||
| LEAKAGE CURRENT | <0.75mA / 277VAC | |||||
| NO LOAD POWER CONSUMPTION | <0.5W for Blank-Type, <1.2W for A-Type | |||||
| PROTECTION | SHORT CIRCUIT | Shut down O/P voltage, re-power on to recovery | ||||
| OVER CURRENT | 105 ~ 115% | |||||
| Protection type : Hiccup mode, recovers automatically after fault condition is removed | ||||||
| ENVIRONMENT | WORKING TEMP. | Tcase=-20 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section) | ||||
| MAX. CASE TEMP. | Tcase=+85℃ | |||||
| WORKING HUMIDITY | 20 ~ 90% RH non-condensing | |||||
| STORAGE TEMP., HUMIDITY | -40 ~ +80℃, 10 ~ 95% RH | |||||
| TEMP. COEFFICIENT | ±0.03%/℃ (0 ~ 50℃) | |||||
| VIBRATION | 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes | |||||
| SAFETY & EMC | SAFETY STANDARDS | UL8750(type”HL”),CSA C22.2 NO.250.13-12;ENEC BS EN/EN61347-1 & BS EN/EN61347-2-13 independent, BS EN/EN62384,GB19510.1,GB19510.14; BIS IS15885( for ODLV-45-12,24,48 only), EAC TP TC 004,IP67 approved | ||||
| WITHSTAND VOLTAGE | I/P-O/P:3.75KVAC | |||||
| ISOLATION RESISTANCE | I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH | |||||
| EMC EMISSION | Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@load≧60%) ; BS EN/EN61000-3-3,GB17743, GB17625.1,EAC TP TC 020 | |||||
| EMC IMMUNITY | Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level(surge immunity: Line-Line:1KV),EAC TP TC 020 | |||||
| OTHERS | MTBF | 388.02K hrs min. MIL-HDBK-217F (25℃) | ||||
| DIMENSION | 111*77*28.5mm (L*W*H) | |||||
| PACKING | 0.42Kg;24pcs/11Kg/ 0.72CUFT | |||||
| NOTE | 1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature. 2. De-rating may be needed under low input voltages. Please refer to “Stack CHARACTERlSTlC” sections for details. 3. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time. 4. Aux. 12V will be damaged with short circuit; lt will not be available with dimming off or output no load condition. 5. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 6. The ambient temperature derating of 3.5℃/1000m with finless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft). 7. For any application note and lpm water proof function installation caution, please refer our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf 8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains. ※ Product Liability Disclaimer: For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx |
|||||
DIMMING OPERATION
※ Dimming principle for PWM style output
- Dimming is achieved by varying the duty cycle of the output current.
※ 2in 1dimming function
© Applying additive 0~ 10VDC
Note :
- Min. duty cycle of output current is about 8% and the output current s not defined when 0%< Iout<8%.
- The duty cycle of output current could drop down to 0% when dimming input is about 0Vdc or 10V PWM signal with 0% duty cycle.
OUTPUT LOAD vs TEMPERATURE
STATIC CHARACTERISTIC
De-rating is needed under low input voltage.
De-rating is needed under low input voltage.
POWER FACTOR (PF) CHARACTERISTIC
Tcase at75C
TOTAL HARMONIC DISTORTION (THD)
60V Model, Tcase at 75°C
EFFICIENCY vs LOAD
ODLV-45 series possess superior working efficiency that up to 90% can be reached in field applications. 60V Model, Tcase at 75
BLOCK DIAGRAM
DRIVING METHODS OF LED MODULE
MECHANICAL SPECIFICATION
INSTALLATION MANUAL
Please refer to : http://www.meanwell.com/manual.htm|
File Name: ODLV-45-SPEC 2022-01-24
Documents / Resources
 |
MEAN WELL ODLV-45-12 45W PWM Output LED Driver [pdf] Owner's Manual ODLV-45-12 45W PWM Output LED Driver, ODLV-45-12, 45W PWM Output LED Driver, Output LED Driver, LED Driver, Driver |