Contents hide
1 MEAN WELL APV-35 Series 35W Single Output Switching Power Supply
2 Product Information
3 Product Usage Instructions
4 GTIN CODE
5 Features
6 SPECIFICATION
7 Mechanical Specification
8 Block Diagram
9 Derating Curve
10 Static Characteristics
11 Documents / Resources
11.1 References

MEAN-WELL-Logo

MEAN WELL APV-35 Series 35W Single Output Switching Power Supply

MEAN-WELL-APV-35-Series-35W-Single-Output-Switching-Power-Supply-Product

Product Information

Specifications:

  • Model: APV-35-5, APV-35-12, APV-35-15, APV-35-24, APV-35-36
  • Output Voltage: 5V, 12V, 15V, 24V, 36V
  • Rated Current: 5A, 3A, 2.4A
  • Rated Power: 25W, 36W
  • Ripple & Noise: 120mVp-p, 150mVp-p
  • Efficiency: 76.5%, 83%, 84%
  • Operating Temperature: -30°C to 70°C
  • Working Humidity: 20% to 90% RH non-condensing
  • Safety Standards: UL8750, CSA-C22.2 No. 250.0-13, BIS IS15885, EAC TP TC 004, IP42, BS EN/EN 62368-1 Approved
  • EMC Compliance: BS EN/EN55032, BS EN/EN61000-3-2 Class A, BS EN/EN61000-3-3
  • Isolation Resistance: I/P-O/P:3KVAC I/P-O/P:>100M Ohms/500VDC

Product Usage Instructions

Installation:

  1. Ensure the input power source matches the voltage range specified (90 ~ 264VAC).
  2. Connect the output terminals to your device following the correct polarity (V+ and V-).

Operation:

  1. Power on the switching power supply using the AC/N and AC/L terminals.
  2. Monitor the load current to ensure it stays within the specified range for each model.

Safety Precautions:

  1. Do not exceed the maximum current and voltage ratings to prevent damage.
  2. Keep the power supply away from moisture and high temperatures to ensure proper operation.

FAQ:

  • Q: What should I do if the power supply overheats?
    A: Ensure proper ventilation around the power supply and reduce the load if necessary to prevent overheating.
  • Q: Can I use this power supply for LED lighting applications?
    A: This product is not intended for LED lighting luminaire applications in the EU. Refer to the LPF/NPF/XLG series for such purposes.

User’s Manual

MEAN-WELL-APV-35-Series-35W-Single-Output-Switching-Power-Supply-Fig-1

GTIN CODE

MW Search: https://www.meanwell.com/serviceGTIN.aspx.

Features

  • Constant voltage mode power supply
  • Universal AC input / Full range
  • Withstand 300VAC Surge input for 5 seconds
  • Protections: Short circuit / Over load / Over voltage
  • Fully isolated plastic case
  • Cooling by free air convection
  • Small and compact size
  • IP42 design
  • Class 2 power unit
  • Pass LPS
  • 100% full load burn-in test
  • Low cost, high reliability
  • Suitable for LED-related fixtures or appliances (such as LED Decoration or Advertisement devices) (Note.10)
  • 2 years warranty.

MEAN-WELL-APV-35-Series-35W-Single-Output-Switching-Power-Supply-Fig-2

SPECIFICATION

MODEL APV-35-5 APV-35-12 APV-35-15 APV-35-24 APV-35-36
 

 

 

 

OUTPUT

 DC VOLTAGE 5V 12V 15V 24V 36V
RATED CURRENT 5A 3A 2.4A 1.5A 1A
CURRENT RANGE 0 ~ 5A 0 ~ 3A 0 ~ 2.4A 0 ~ 1.5A 0 ~ 1A
RATED POWER 25W 36W 36W 36W 36W
RIPPLE & NOISE (max.) Note.2 120mVp-p 150mVp-p 150mVp-p 180mVp-p 180mVp-p
VOLTAGE TOLERANCE Note.3 ±5.0%
LINE REGULATION ±1.0%
LOAD REGULATION ±2.0%
SETUP, RISE TIME Note.6 1500ms, 40ms / 230VAC             1500ms,40ms / 115VAC at full load
HOLD UP TIME (Typ.) 20ms/230VAC           12ms/115VAC at full load
 

 

INPUT

 VOLTAGE RANGE Note.4 90 ~ 264VAC           127 ~ 370VDC
FREQUENCY RANGE 47 ~ 63Hz
EFFICIENCY (Typ.) 76.5% 83% 84% 84% 85%
AC CURRENT 0.5A/230VAC 0.75A/115VAC
INRUSH CURRENT(Typ.) COLD START 45A(twidth=440μs measured at 50% Ipeak) at 230VAC
MAX. No. of PSUs on 16A CIRCUIT BREAKER 6 units (circuit breaker of type B) / 10 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT 0.25mA / 240VAC
 

PROTECTION

 OVERLOAD 110%~160% rated output power
Protection type: Hiccup mode, recovers automatically after fault condition is removed
OVERVOLTAGE 5.75 ~ 6.95V 13.8 ~ 16.2V 17.25 ~ 21V 27 ~ 32.4V 41.4 ~ 48.6V
Protection type: Shut down o/p voltage, re-power on to recover
 

 

ENVIRONMENT

 WORKING TEMP. -30 ~ 70℃(Refer to “Derating Curve”)
WORKING HUMIDITY 20 ~ 90% RH non-condensing
STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 50℃)
VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, and Z axes
 

SAFETY & EMC

 SAFETY STANDARDS UL8750 , CSA-C22.2 No. 250.0-13, BIS IS15885, EAC TP TC 004,IP42 , BS EN/EN 62368-1 Approved
WITHSTAND VOLTAGE I/P-O/P:3KVAC
ISOLATION RESISTANCE I/P-O/P:>100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION Compliance to BS EN/EN55032,BS EN/EN61000-3-2 Class A,BS EN/EN61000-3-3, EAC TP TC 020
EMC IMMUNITY Compliance to BS EN/EN55035,BS EN/EN61000-4-2,3,4,5,6,8,11; light industry level(surge 2KV), EAC TP TC 020
 

OTHERS

 MTBF 5489.6K hrs min.       Telcordia SR-332 (Bellcore);      600.8K hrs min. MIL-HDBK-217F (25℃)  
DIMENSION 84*57*29.5mm (L*W*H)
PACKING 0.18Kg; 72pcs / 14Kg/ 0.92CUFT
NOTE 1.   All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.

2.   Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3.   Tolerance: includes set up tolerance, line regulation and load regulation.

4.   Derating may be needed under low input voltage. Please check the static characteristics for more details.

5.   The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify the EMC Directive on the complete installation. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)

6.   Length of set up time is measured at the first cold start. Turning ON/OFF the power supply may lead to an increase in the set-up time.

7.   The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitudes higher than 2000m(6500ft).

8.   Products sourced from the Americas regions may not have the ENEC/BIS/CCC logo. Please contact your MEAN WELL sales for more information.

9.   For any application note and IP waterproof function installation caution, please refer to our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf

10.    This product is not intended for LED lighting luminaire applications in the EU. (In the EU the LPF/NPF/XLG series are recommended.)

※ Product Liability Disclaimer: For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx.

Mechanical Specification

Case No.PCD16A Unit: mm

MEAN-WELL-APV-35-Series-35W-Single-Output-Switching-Power-Supply-Fig-3

Block Diagram

fosc: 60KHz

MEAN-WELL-APV-35-Series-35W-Single-Output-Switching-Power-Supply-Fig-4

Derating Curve

MEAN-WELL-APV-35-Series-35W-Single-Output-Switching-Power-Supply-Fig-5

Static Characteristics

MEAN-WELL-APV-35-Series-35W-Single-Output-Switching-Power-Supply-Fig-6

Documents / Resources

MEAN WELL APV-35 Series 35W Single Output Switching Power Supply [pdf] Owner's Manual
APV-35 Series, APV-35 Series 35W Single Output Switching Power Supply, 35W Single Output Switching Power Supply, Single Output Switching Power Supply, Output Switching Power Supply, Switching Power Supply, Power Supply
MEAN WELL APV-35 Series 35W Single Output Switching Power Supply [pdf] Owner's Manual
APV-35-5, APV-35-12, APV-35-15, APV-35-24, APV-35-36, APV-35 Series 35W Single Output Switching Power Supply, APV-35 Series, 35W Single Output Switching Power Supply, Single Output Switching Power Supply, Switching Power Supply, Power Supply, Supply

References

Leave a comment

Your email address will not be published. Required fields are marked *