MEAN WELL AD-155A 155W Single Output with Battery Charging UPS Function Owner's Manual

MODEL		AD155-A		AD155-B		AD1 55-C
OUTPUT	OUTPUTNUMBER	CH1	CH2	CH1	CH2	CH1	CH2
	DC VOLTAGE	13.8V	13.3V	27.6V	27.1V	54V	53.5V
	RATED CURRENT	10.5A	0.5A	5A	0.5A 0-0.5A	2.7A 0- 2.7A	0.2A 0 – 0.5A
	CURRENTRANGE	0 – 11.5A	0 – 0.5A	0-55A
	RATED POWER	151.55W		151.55W		156.55W
	RIPPLE& NOISE(max.) Note.,	15-0tm/p-p	—	150mVp-p	—-	240mVp-p	—
	VOLTAGEADJ. RANGE	CH1: 12- 14.5V		CH1 : 24 -29V		CH1 : 48-58V
	VOLTAGETOLERANCE Note.3LINEREGULATION	±2.0% ±0.5%	— — — —	±1.0% ±0.5%	– — ——	±1.0% ±0-.5%	— —-
	LOAD REGULATION	±o.5%	– –	±0.5%	— —	±o.5%	—
	SETU,PRISE TIME	1OOOms, 90ms/230VAC 2000ms, 90ms/115VACat full load
	HOLD UP TIME (Typ,)	24ms/230VAC 2oms115VACat ru11 l o ad
INPUT	VOLTAGE RANGE FREQUENCYRANGE	88 – 264VAC 124- 370VDC 47 – 63Hz
	POWER FACTOR ( Typ.)	PF>0.92at lull load
	EFFICIENCY(Typ)	80%			84%
	ACCURRENT(Typ.)	2.5A/115VAC 1.5A/230VAC
	INRUSH CURRENT(Typ.) LEAKAGE CURRENT	COLD START 23A1115VAC 45A/’230VAC <1mA/24 0VAC

PROTFCTION	OVERLODA	CH1:105- 135% CH2:0.51 -0.9Arated output power
		Protection Type : AC Charging Mode : Constant current limiting, recover automatically after fault condition is removed UPS Mode : Protected by Internal fuse
	OVERVOLTAGE BATTERYLOW	CH1:1 .87- 18.G3V		CH1:31.74- 37.26V		CH1G: 2.1- 72.9Y
		Protection Type : Shut down O/P voltage, e re-power on to recover 10VJ:0.8 V f1 9.5V(+1.5V-1,V) 39V±2V
ENVIRONMENT	WORKINGTEMP.	-10 – +60ºC (Refer lo “Derating Curve”)
	WORKING HUMIDITY	20 – 90% RH non-condensing
	STORAGE TEM.P, HUMIDITY	-20- +85-ºC, 10 – 95%RH
	TEMP. COEFFICIETN	±o 03%FC (0 – 50ºC)
	VIBRATION	10- 500Hz. 2G10mni .11cycle,60min.each along X. Y. Z axes
SAFETY & EMC (Note4)	SAFETY STANDARDS	UL62368-1, TW esENIEN62368-1A, SINZS 62368.1, EAC TPTC 004 approved
	WITHSTANDVOLTAGE	IIP-OIP:3KVAC 1/P-F G:1.SKYAC 0/P-FG:O.SKYAC
	ISOLATION RESISTANCE	IIP-0/ P, I/P-FG, 0/P-FG:1OOM Ohms/ 500VDCI 25″C/ 70%RH
	EMCEMISSION EMCIMMUNITY	Compliance to BSEN/EN5S032 (CISPR32)Class B,BSEN/EN61000-3-2,-3,EAC TP TC 020
		Compliance to BS EN/EN6100-4-2.3.4.5.6.8.11. esENIENS5024. light industry level. criteria A EAC TP TC020
OTHERS	MTBF	183.3Khr min. MIL-HDBK-217F /25’CI
	DIM ENSION	199•110•50,nm (L-w-H)
	PACKING	0,88Kg; 11pi CS/15Kg/0.9oCUFI
NOTE	All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature. Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1 uf & 47uf parallel capacitor. Tolerance: includes set up tolerance, line regulation and load regulation. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives.

Mechanical Specification

Terminal Pin No. Assignment

Pi n No . 1	Assignment AC/L	Pin No . 5	Assignment BAT+
2	AGIN	6	BAT. -/COM
3	FG	7	DC OUTPUTCOM
4	NC	8	DCOUTPUT+V

CN1 Pin No. Assignment :JST B2B-XH or equivalent

Pin No.	Assignment	Mating Housing	Terminal
1	RESET SW	JST XHP or equivalent	JST SXH-001T-P0.6 or equivalent
2

Block Diagram

Derating Curve

Output Derating VS Input Voltage (A)

OPTIONAL DIN RAIL MOUNTING KIT

SIMPLY ADD THE SUFFIX “/DRL” TO THE END OF THE MODEL NUMBER. I.E. “AD155-A/DRL”

Documents / Resources

MEAN WELL AD-155A 155W Single Output with Battery Charging UPS Function [pdf] Owner's Manual
AD-155A 155W Single Output with Battery Charging UPS Function, AD-155A, 155W Single Output with Battery Charging UPS Function, Output with Battery Charging UPS Function, Battery Charging UPS Function, Charging UPS Function, UPS Function, Function

References

User Manual

Features

SPECIFICATION