Contents hide
1 MEAN WELL PLC-30-9 Single Output LED Power Supply With PFC
2 Features
3 SPECIFICATION
4 Mechanical Specification
5 Block Diagram
6 Derating Curve
7 Static Characteristics
8 Power Factor Characteristic
9 EFFICIENCY VS LOAD (48V Model)
10 DRIVING METHODS OF LED MODULE
11 Documents / Resources
11.1 References

MEAN-WELL-LOGO

MEAN WELL PLC-30-9 Single Output LED Power Supply With PFC

MEAN-WELL-PLC-30-9-Single-Output-LED-Power-Supply-With-PFC-PRODUCT

Features

  • Universal AC input / Full range
  • Adjustable output voltage and current level
  • Protections: Short circuit / Over current / Over voltage/ Over temperature
  • Cooling by free air convection
  • Built-in constant current limiting circuit
  • Fully isolated plastic case with terminal block style of I/O
  • Built-in active PFC function, comply with BS EN/EN61000-3-2 class C (Pin≥25W)
  • Class II power unit, no FG
  • Class 2 power unit
  • 100% full load burn-in test
  • High reliability
  • Suitable for LED lighting and moving sign applications (Note.2)
  • Compliance to worldwide safety regulations for lighting
  • 2 years warranty

MEAN-WELL-PLC-30-9-Single-Output-LED-Power-Supply-With-PFC-FIG-9

User’s Manual

MEAN-WELL-PLC-30-9-Single-Output-LED-Power-Supply-With-PFC-FIG-8

SPECIFICATION

MODEL PLC-30-9 PLC-30-12 PLC-30-15 PLC-30-20 PLC-30-24 PLC-30-27 PLC-30-36 PLC-30-48
 

 

 

 

 

OUTPUT

 DC VOLTAGE 9V 12V 15V 20V 24V 27V 36V 48V
CONSTANT CURRENT REGION Note.6 6.3 ~ 9V 8.4 ~ 12V 10.5 ~ 15V 14 ~ 20V 16.8 ~ 24V 18.9 ~ 27V 25.2 ~ 36V 33.6 ~ 48V
RATED CURRENT 3.3A 2.5A 2A 1.5A 1.25A 1.12A 0.84A 0.63A
CURRENT RANGE 0 ~ 3.3A 0 ~ 2.5A 0 ~ 2A 0 ~ 1.5A 0 ~ 1.25A 0 ~ 1.12A 0 ~ 0.84A 0 ~ 0.63A
RATED POWER 29.7W 30W 30W 30W 30W 30.24W 30.24W 30.24W
RIPPLE & NOISE (max.) Note.2 2.6Vp-p 2Vp-p 2.6Vp-p 2.6Vp-p 2.4Vp-p 2.3Vp-p 3.6Vp-p 3.7Vp-p
VOLTAGE ADJ. RANGE Note.5 8.55 ~ 9.9V 11.4 ~ 13.2V 14.5 ~ 16.5V 19 ~ 22V 22.8 ~ 26.4V 25.65 ~ 29.7V 34.2 ~ 39.6V 45.6 ~ 52.8V
CURRENT ADJ. RANGE Note.5 2.475 ~ 3.399A 1.875 ~ 2.575A 1.5 ~ 2.06A 1.125 ~ 1.545A 0.938 ~ 1.288A 0.84 ~ 1.1536A 0.63 ~ 0.865A 0.473 ~ 0.649A
VOLTAGE TOLERANCE Note.3 ±10%
LINE REGULATION ±3.0%
LOAD REGULATION ±5.0%
SETUP TIME 500ms / 230VAC  3000ms / 115VAC at full load
 

 

 

 

INPUT

 VOLTAGE RANGE             Note.4 90 ~ 264VAC             127 ~ 370VDC
FREQUENCY RANGE 47 ~ 63Hz
POWER FACTOR (Typ.) PF>0.95/115VAC, PF>0.9/230VAC at full load (Please refer to “Power Factor Characteristic” curve)
TOTAL HARMONIC DISTORTION THD< 20% when output loading≧70% at 115VAC/230VAC input
EFFICIENCY (Typ.) 80% 82.5% 83.5% 84% 84% 84.5% 85% 85.5%
AC CURRENT (Typ.) 0.4A/115VAC  0.2A/230VAC
INRUSH CURRENT (Typ.) COLD START 35A(twidth=25μs measured at 50% Ipeak) at 230VAC
MAX. No. of PSUs on 16A CIRCUIT BREAKER 64 units (circuit breaker of type B) / 64 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT <0.5mA / 240VAC
 

 

 

PROTECTION

 OVER CURRENT 100 ~ 110%
Protection type : Constant current limiting, recovers automatically after fault condition is removed
SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed.
OVER VOLTAGE 10 ~ 14V 14 ~ 17V 17 ~ 22V 23 ~ 26V 27 ~ 34V 31 ~ 35V 40 ~ 50V 53 ~ 63V
Protection type : Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE Shut down o/p voltage, re-power on to recover
 

 

ENVIRONMENT

 WORKING TEMP. -30 ~ +50℃ (Refer to “Derating Curve”)
WORKING HUMIDITY 20 ~ 95% RH non-condensing
STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT ±0.06%/℃ (0 ~ 50℃)
VIBRATION 10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes
 

 

SAFETY & EMC

 SAFETY STANDARDS UL1310, TUV BS EN/EN61347-1, BS EN/EN61347-2-13, GB19510.14,GB19510.1, CAN/CSA C22.2 No. 223-M91(except for 48V),

EAC TP TC 004 approved
WITHSTAND VOLTAGE I/P-O/P:3.75KVAC
ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION Compliance to BS EN/EN55015, GB17743, GB17625.1,BS EN/EN61000-3-2 Class C (Pin≧25W), Class D (>70% load) ;

BS EN/EN61000-3-3,EAC TP TC 020
EMC IMMUNITY Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN55024, BS EN/EN61547, light industry level, criteria A,EAC TP TC 020
 

OTHERS

 MTBF 625.5Khrs min.  MIL-HDBK-217F (25℃)
DIMENSION 160*46*30mm (L*W*H)
PACKING 0.2Kg; 70pcs/15Kg/0.96CUFT

NOTE

  1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.
  2. Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0. 1uf & 47uf parallel capacitor.
  3. Tolerance : includes set up tolerance, line regulation and load regulation.
  4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
  5. Output voltage can be adjusted through the SVR1 on the PCB; limit of output constant current level can be adjusted through the SVR2 on the PCB.
  6. Please refer to “DRIVING METHODS OF LED MODULE”.
  7. The power supply is considered as a component that will be operated in combination with final equipment. Since MC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify MC Directive on the complete installation again.
  8. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
  9. To fulfill requirements of the latest Er regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains.
  10. The ambient temperature derating of 3.5°C/1000m with fanless models and of 5°C/1000m with fan models for operating altitude higher than 2000m(6500ft.
  11. PLC-30-9 is used for any light source that exempt from the ErP-Directive (EU) 2019/2020 requirement, for example this model could be
    use for signalling products (including, but not limited to road-, railway-, marineorair traffic-signalling, traffic control or airfield lamps).
  12. Product Liability Disclaimer: For detailed information, please refer to httos://www.meanwell.com/serviceDisclaimer.aspx File Name:PLC-30-SPEC 2021-12-

Mechanical Specification

MEAN-WELL-PLC-30-9-Single-Output-LED-Power-Supply-With-PFC-FIG-1

Block Diagram

MEAN-WELL-PLC-30-9-Single-Output-LED-Power-Supply-With-PFC-FIG-2

Derating Curve

MEAN-WELL-PLC-30-9-Single-Output-LED-Power-Supply-With-PFC-FIG-3

Static Characteristics

MEAN-WELL-PLC-30-9-Single-Output-LED-Power-Supply-With-PFC-FIG-4

Power Factor Characteristic

MEAN-WELL-PLC-30-9-Single-Output-LED-Power-Supply-With-PFC-FIG-5

EFFICIENCY VS LOAD (48V Model)

  • PLC-30 series possess superior working efficiency that up to 85.5% can be reached in field applications.MEAN-WELL-PLC-30-9-Single-Output-LED-Power-Supply-With-PFC-FIG-6

DRIVING METHODS OF LED MODULE

This LED power supply is suggested to work in constant current mode area (CC) to drive the LEDs.

MEAN-WELL-PLC-30-9-Single-Output-LED-Power-Supply-With-PFC-FIG-7

  • In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems.
  • Should there be any compatibility issues, please contact MEAN WELL.

Documents / Resources

MEAN WELL PLC-30-9 Single Output LED Power Supply With PFC [pdf] Owner's Manual
PLC-30-9 Single Output LED Power Supply With PFC, PLC-30-9, Single Output LED Power Supply With PFC, Output LED Power Supply With PFC, LED Power Supply With PFC, Power Supply With PFC, Supply With PFC, With PFC

References

Leave a comment

Your email address will not be published. Required fields are marked *